开云体育

----- Original Message -----
From: "Chad Nelson via groups.io"
<chad.nelson71@...>
To: <[email protected]>
Sent: Saturday, May 10, 2025 1:44 PM
Subject: Re: [repeater-builder] trying to read data on a kenwood
851 repeater


I changed frequency to 442.100. But not sure about the crackle. I
tried it here and didn't notice any noise on RX.

Give me a call later on tomorrow, since leaving soon.



-----Original Message-----
From: [email protected] <[email protected]> On
Behalf Of Butch-tiny puppy via groups.io
Sent: Saturday, May 10, 2025 2:21 PM
To: [email protected]
Subject: Re: [repeater-builder] trying to read data on a kenwood
851 repeater

The repeater has a noise on receive like bacon frying. Not sure
what is causing that. I can give you a call if you want to
listen to it. kind of a crackling noise. I haven't tried
adjusting anything yet, but sensativity is poor even on the
151.1875 frequency.

Butch Bussen
wa0vjr
wa0vjr@...
irlp 7135
allstar 56023
echolink 790800
new home phone 785 852-1102
----- Original Message -----
From: "Chad Nelson via groups.io"
<chad.nelson71@...>
To: <[email protected]>
Sent: Saturday, May 10, 2025 12:16 PM
Subject: Re: [repeater-builder] trying to read data on a kenwood
851 repeater


That's good to know thanks. Hopefully my little laptop comes by
Wednesday because tentatively planning on going back to the site
in portage on Thursday to visit the lady Buggs, well OK not
really, but putting up the Lincoln tenor for the repeaters and
figuring out what is going on with my DNC. I turned it on and it
gives me a little Gibberish character, but then I turn it off and
back on again and then it works. Might have to just flush the
whole TNC and start over. Would like it just to power up and work
because if there's a power failure and that TNC comes back on
then it won't power up correctly and I'm 70+ miles away from the
site with no transportation.
Chad Nelson WI9HF/WRPL979
Janesville Wisconsin
608-754-8671
Send from my spectrum iPhone 16.

On May 10, 2025, at 12:58?PM, Butch-tiny puppy via groups.io
<wa0vjr@...> wrote:

?yes, works fine. nvda is the best, although works with
window-eyes
as well.

Butch Bussen
wa0vjr
wa0vjr@...
irlp 7135
allstar 56023
echolink 790800
new home phone 785 852-1102
----- Original Message -----
From: "Chad Nelson via groups.io"
<chad.nelson71@...>
To: <[email protected]>
Sent: Saturday, May 10, 2025 11:44 AM
Subject: Re: [repeater-builder] trying to read data on a
kenwood
851 repeater


That was one of my questions I actually had and you might have
just
answered it for me, but, does your Windows XP box work with the
KPG
91D software?
Chad Nelson WI9HF/WRPL979
Janesville Wisconsin
608-754-8671
Send from my spectrum iPhone 16.

On May 10, 2025, at 12:32?PM, Butch-tiny puppy via groups.io
<wa0vjr@...> wrote:

?The computer I usually use doesn't have a serial port and I
can't
find my usb to serial adapter, so fired up my old xp machine
with a
for real serial port.
Thanks all for your help. Good to know about the fuse.

Butch Bussen
wa0vjr
wa0vjr@...
irlp 7135
allstar 56023
echolink 790800
new home phone 785 852-1102
----- Original Message -----
From: "Ken Arck AH6LE via groups.io"
<ken@...>
To: <[email protected]>
Sent: Saturday, May 10, 2025 11:21 AM
Subject: Re: [repeater-builder] trying to read data on a
kenwood
851 repeater


See Chris's comments about the fuse.

BTW, the only reason to use the mic jack is if you're updating
the
firmware (or don't want to otherwise with the rear panel
DB25).

Good to hear you're good to go

Ken



At 10:13 AM 5/10/2025, you wrote:

I tried it on serial port on the back and it works, for some
reason, not on the mike connector on the front which is what
I
use on my other repeaters. Thanks.

Butch Bussen
wa0vjr
wa0vjr@...
irlp 7135
allstar 56023
echolink 790800
new home phone 785 852-1102
----- Original Message -----
From: "Butch-tiny puppy via groups.io"
<wa0vjr@...>
To: <[email protected]>
Sent: Saturday, May 10, 2025 10:43 AM
Subject: Re: [repeater-builder] trying to read data on a
kenwood
851 repeater


that is what I thought, then why do I get that error?

Butch Bussen
wa0vjr
wa0vjr@...
irlp 7135
allstar 56023
echolink 790800
new home phone 785 852-1102
----- Original Message -----
From: "Ken Arck AH6LE via groups.io"
<ken@...>
To: <[email protected]>
Sent: Saturday, May 10, 2025 10:42 AM
Subject: Re: [repeater-builder] trying to read data on a
kenwood
851 repeater


KPG-91D will work

Ken



At 09:40 AM 5/10/2025, you wrote:

I thought my software for my 850 would work, but it says
check
radio model, retry. Does it take a different program?
Thanks.

Butch Bussen
wa0vjr
wa0vjr@...
irlp 7135
allstar 56023
echolink 790800
new home phone 785 852-1102

------------------------------------------------------------------------------
President and CTO - Arcom Controllers
Makers of repeater controllers and accessories
Phone: (503) 678 6182

Authorized Dealers for Kenwood and Telewave.
We offer complete turn-key repeater packages!
"We don't just make 'em. We use 'em!"
[]

------------------------------------------------------------------------------
President and CTO - Arcom Controllers
Makers of repeater controllers and accessories
Phone: (503) 678 6182

Authorized Dealers for Kenwood and Telewave.
We offer complete turn-key repeater packages!
"We don't just make 'em. We use 'em!"
[]