开云体育

I ran across this issue.... 1.? Read the original codeplug and save it to another name. 2.? Open the codeplug you just saved.? It should have "personality" at top of screen.... make your changes

I just bought a BluMax cable and plugged in to my WinXP/32 laptop.? I can read/write an MTR-2000 just fine.? A friend has another MTR-2000 with BluMax cable with Win7/32 and he cannot read or

As others have said MTR2000's CPS only runs on a Windows 32bit OS. I have a Windows 10 Pro 32bit installation that works fine using a USB to Serial adapter, I have an old Windows XP Pro computer with

Most likely you have the unit setup as a reciever... hafta change it into repeater mode..cant remember where the setting was for this

I emailed blue max for a return but have better and worse news at the same time. made my own cable with the db9 cable. Worked like a charm. issue arises…. can read the station and see all the stuff

You don't mention that you contacted Bluemax49.? I've purchased several cables from him and had no problem.? He was good about answering questions. Joe, K1ike

I have a 2660D and would love to connect an LCD monitor to my unit. Sent: Wednesday, March 19, 2025 9:23 AM To: [email protected] Subject: Re: [repeater-builder] Motorola R2600 VGA

Likely an issue with drivers and/or OS versions as described above? I have NEVER had a Bluemax49er cable failure to work as described. They are my FIRST choice for cables with any of my projects.

In ham radio - it's possible to have the transmitter appear on either side of the receiver.? With duplexers that provide symmetrical performance - duplexer ports marked "Transmit" and "Receive" or

Ok so this is the setup. IBM Lenovo laptop 697 MHz with 0.97 megs of ram 1 gig basically. running windows xp 32 bit no true com port but two usb available. Installed all the different persons of the

I programmed a MTR-2000 with my laptop running 32 bit Windows 7 and a USB --> RS-232 adapter. Mick - W7CAT

The band pass is tuned by the shaft. The capacitor tunes the notch only.. I use a spectrum analyzer and service monitor to tune my Wacoms, DBs, TXRX, etc..Kit Parsons at Wacom suggested a signal

Gentlemen, What is the "Proper" way to tune a 443mhz bpbr Wacom ? S11 with a 50 ohm load at the antenna port? or S21? ? I can "see"? ( and tune ) the notch on S11 , but the notch is

MTR CPS does not run on anything above win XP Chris WB5ITT [email protected]> wrote:

Excuse me?? To talk to the MTR takes a RJ45 cable to DB9 adapter.. I wired one up myself in 5 minutes that works. I've never had a problem with Blue Max 49 as far as his cables are concerned. The MTR

Part number of cable?? ? RS-232(DB-9 or DB-25 on PC?) to radio adapter (native RS-232 port on PC) or using a USB-to-radio adapter cable? Another way of asking that - does the (un-named make/model)

I bought 2 for a HT1250 and a XTS3000. Both work great on Win 7 32 bit. Make sure you install the FTDI driver. Cecil

I bought one off ebay to program a Kenwood and it installed just on 2 different computers that has Win 10 on them.? No problem installing them and loading the program and programming the

Did you get a counterfeit?? Or is this on win xp? Sometimes you can get this to work on Windows 10 but other than that the old radio software will not work on Windows 10 and definitely will not

Ordered one of these cables to get the Mtr to read and after spending 3 hours of my life I will never get back cable refused to install. anyone else have this issue where no matter what you do as an