Re: fldigi abort witnessed - Pi 4.2.05.24
Rick,
I also use fldigi 4.2.05 on a Pi4 using Buster. My system was stable for until I started using flmsg. With it running, fldigi would freeze every few days. Without it, I can operate two simultaneous instantiations of fldigi (FSQ and Thor) for weeks without problems.
Scott W3WT
toggle quoted message
Show quoted text
On Jan 5, 2025, at 21:45, Rick KD8WCK <rademattia@...> wrote:
?I'm running fldigi 4.2.05.24 on a RaspberryPi4 on Raspbian 10 buster. The station runs 24/7 and several times a week when I remote in to the Pi I find fldigi is no longer running.
This evening I was actually looking at the display when it happened. I had entered a command, and it timed out dues to open squelch, reported that in the receive pan then immediately aborted.
Anything I can look for to help troubleshot this issue?
|
Re: #flrig 2.0.05 Pi3 PTT-GPIO menu?
#flrig
OK, thanks, Dave.? I'll tinker some more with this and see if I can figure out what I did wrong.
?
Eric
|
Re: #flrig 2.0.05 Pi3 PTT-GPIO menu?
#flrig
Last alpha posted:
should still be in compliance with
But I am not able to test any GPIO controls at this time.?
Perhaps another user might be able to assist you.
David
On 1/6/25 18:53, Eric Hansen, KB1VUN
via groups.io wrote:
toggle quoted message
Show quoted text
No change with alpha.? In response to your first reply, I
don't think I confused flrig with fldigi.? Section 3.1.4 of the
flrig manual talks about the PTT-GPIO option,
, and shows the
menu that I believe I used in the 1.3-ish version.
?
I'm not clear about how flrig is supposed to be aware of the
gpio command in the WiringPi package.? I can run gpio as a
command and the gpio pins obey.? For flrig, do I need to start a
daemon process, or compile flrig with the WiringPi library, or
does flrig just fail if I ask it to set a pin and gpio isn't
present in the system?
?
Thanks much for your help,
Eric
?
?
|
Re: #flrig 2.0.05 Pi3 PTT-GPIO menu?
#flrig
No change with alpha.? In response to your first reply, I don't think I confused flrig with fldigi.? Section 3.1.4 of the flrig manual talks about the PTT-GPIO option, http://www.w1hkj.com/alpha/flrig/flrig_help.pdf, and shows the menu that I believe I used in the 1.3-ish version.
?
I'm not clear about how flrig is supposed to be aware of the gpio command in the WiringPi package.? I can run gpio as a command and the gpio pins obey.? For flrig, do I need to start a daemon process, or compile flrig with the WiringPi library, or does flrig just fail if I ask it to set a pin and gpio isn't present in the system?
?
Thanks much for your help,
Eric
?
?
|
Hi Robert,
You are most welcome in this group. Thank you for introducing yourself. If your questions are inwith the knowledge of our members then I am sure you'll get an answer.?
73 Phil GM3ZZA
toggle quoted message
Show quoted text
It’s who I am as there was not a place for a call sign at registration if call sign was not embedded in your email address. I’m a newer Linux user but trying to go there and end the use of Windows. So I’m looking for a resource for amateur radio
software for a Linux help group. If this isn’t what your group is then please disregard and I’m sorry to bother you. Be well K9TWC.?
On Jan 5, 2025, at 4:37?PM, Bob Groselle, KQ5DX via groups.io <bobgroselle@...> wrote:
?
Is that a question?
Call Sign KQ5DX Email bobgroselle@... or bob.groselle@...
On Sunday, January 5, 2025 at 01:12:46 PM CST, Robert Hadley, K9TWC via groups.io <rhadley06@...> wrote:
Requesting membership. No email with call sign.
|
Re: FLDIGI and sequoia. linux
Hi John, David now has the ability to sign and notarize Mac apps. The latest I’ve downloaded is:
Just download, click on the .dmg file and the app will appear. Drag the app to your Applications folder. Double click on the app and you’ll get this:
Click on open and you should be good to go!
toggle quoted message
Show quoted text
On Jan 6, 2025, at 4:29?PM, John Wiener via groups.io <jawodms@...> wrote:
On Sat, Dec 14, 2024 at 12:57 PM, Gary Rogers, KO3F wrote:
fldigi-4.2.06.15.zip
Thanks, Gary. I'm just now getting to it and it appears that the file has been deleted.
John AB8O
|
Re: FLDIGI and sequoia. linux
On Sat, Dec 14, 2024 at 12:57 PM, Gary Rogers, KO3F wrote:
fldigi-4.2.06.15.zip
Thanks, Gary. I'm just now getting to it and it appears that the file has been deleted.
John AB8O
|
Re: #flrig 2.0.05 Pi3 PTT-GPIO menu?
#flrig
Please try 4.2.05.93 posted at
David
|
Re: #flrig 2.0.05 Pi3 PTT-GPIO menu?
#flrig
I am investigating
On 1/6/25 13:41, Dave, W1HKJ wrote:
toggle quoted message
Show quoted text
Are you confusing flrig and
fldigi?
David
On 1/6/25 12:56, Eric Hansen, KB1VUN
via groups.io wrote:
I just installed FLrig 2.0.05 on a Pi3B+ running Bullseye.?
WiringPi is also installed, and the gpio command works.?
?
My previous FLrig (1.3-ish) had a PTT-GPIO configuration
panel.? It didn't work for me, but I had hopes it might in
this new version.? The panel is missing altogether in the new
version.? I can select Config > Setup > PTT-GPIO, but it
just takes me to a similar menu lacking the GPIO option. ?
?
Anybody have some knowledge / wisdom to share?
?
Thanks,
Eric
|
Re: #flrig 2.0.05 Pi3 PTT-GPIO menu?
#flrig
Are you confusing flrig and
fldigi?
David
On 1/6/25 12:56, Eric Hansen, KB1VUN
via groups.io wrote:
toggle quoted message
Show quoted text
I just installed FLrig 2.0.05 on a Pi3B+ running Bullseye.?
WiringPi is also installed, and the gpio command works.?
?
My previous FLrig (1.3-ish) had a PTT-GPIO configuration
panel.? It didn't work for me, but I had hopes it might in this
new version.? The panel is missing altogether in the new
version.? I can select Config > Setup > PTT-GPIO, but it
just takes me to a similar menu lacking the GPIO option. ?
?
Anybody have some knowledge / wisdom to share?
?
Thanks,
Eric
|
#flrig 2.0.05 Pi3 PTT-GPIO menu?
#flrig
I just installed FLrig 2.0.05 on a Pi3B+ running Bullseye.? WiringPi is also installed, and the gpio command works.?
?
My previous FLrig (1.3-ish) had a PTT-GPIO configuration panel.? It didn't work for me, but I had hopes it might in this new version.? The panel is missing altogether in the new version.? I can select Config > Setup > PTT-GPIO, but it just takes me to a similar menu lacking the GPIO option. ?
?
Anybody have some knowledge / wisdom to share?
?
Thanks,
Eric
|
It’s who I am as there was not a place for a call sign at registration if call sign was not embedded in your email address. I’m a newer Linux user but trying to go there and end the use of Windows. So I’m looking for a resource for amateur radio software for a Linux help group. If this isn’t what your group is then please disregard and I’m sorry to bother you. Be well K9TWC.?
toggle quoted message
Show quoted text
On Jan 5, 2025, at 4:37?PM, Bob Groselle, KQ5DX via groups.io <bobgroselle@...> wrote:
?
Is that a question? Call Sign KQ5DX Email bobgroselle@... or bob.groselle@...
On Sunday, January 5, 2025 at 01:12:46 PM CST, Robert Hadley, K9TWC via groups.io <rhadley06@...> wrote:
Requesting membership. No email with call sign.
|
Re: fldigi abort witnessed - Pi 4.2.05.24
Rule out:
?
1) RFI. Nearly all problems with this setup are RFI until proven otherwise, including the RF from your antenna being too close to the computer (or battery sometimes).?
2) Vibration or movement of the computer-radio interface cable.
3) Static electricity sources
4) Aging micro SD card in the pi
5) Check uptime to verify if fldigi is crashing or if the computer is just power cycling.
?
|
Re: fldigi abort witnessed - Pi 4.2.05.24
Rick,
I'm seeing the same issue with my Linux Mint 22 machine using Fldigi
4.2.06. Usually during a busy net Fldigi just stops. When I run TOP
it tells me that Fldigi is running way above 100% CPU utilization.
It's intermittent and during FM and HF nets. It happened to 2
different computers, new Linux and Fldigi build. I can't be sure but
it may have started happening when Linux moved to Pipe Wire audio. I
am using the WIKI for the Fldigi build.
I don't have any problems using Windows.
73, Ron NY3J
On 1/5/2025 10:26 PM, Bob Cameron,
VK2YQA via groups.io wrote:
toggle quoted message
Show quoted text
Hi Rick
.xsession-errors in the home directory usually contains the
terminal output of any application errors. The other possibility
being run fldigi from a terminal.
A look at the journal or syslog plus dmesg may also contain
some clues. ie things that happened at the same time the program
died.
Also possible to run fldigi from the debugger. Would be a good
idea to build to the latest version first though. Buster is
getting a bit old too.
Cheers Bob VK2YQA
On 6/1/25 13:45, Rick KD8WCK wrote:
I'm running fldigi 4.2.05.24 on a RaspberryPi4 on Raspbian 10 buster. The station runs 24/7 and several times a week when I remote in to the Pi I find fldigi is no longer running.
This evening I was actually looking at the display when it happened. I had entered a command, and it timed out dues to open squelch, reported that in the receive pan then immediately aborted.
Anything I can look for to help troubleshot this issue?
|
Re: fldigi abort witnessed - Pi 4.2.05.24
Hi Rick
.xsession-errors in the home directory usually contains the
terminal output of any application errors. The other possibility
being run fldigi from a terminal.
A look at the journal or syslog plus dmesg may also contain some
clues. ie things that happened at the same time the program died.
Also possible to run fldigi from the debugger. Would be a good
idea to build to the latest version first though. Buster is
getting a bit old too.
Cheers Bob VK2YQA
On 6/1/25 13:45, Rick KD8WCK wrote:
toggle quoted message
Show quoted text
I'm running fldigi 4.2.05.24 on a RaspberryPi4 on Raspbian 10 buster. The station runs 24/7 and several times a week when I remote in to the Pi I find fldigi is no longer running.
This evening I was actually looking at the display when it happened. I had entered a command, and it timed out dues to open squelch, reported that in the receive pan then immediately aborted.
Anything I can look for to help troubleshot this issue?
|
Re: fldigi abort witnessed - Pi 4.2.05.24
Bad typing, sorry:
"timed out due to open squelch"
"in the receive pane"
sri de KD8WCK
|
fldigi abort witnessed - Pi 4.2.05.24
I'm running fldigi 4.2.05.24 on a RaspberryPi4 on Raspbian 10 buster. The station runs 24/7 and several times a week when I remote in to the Pi I find fldigi is no longer running.
This evening I was actually looking at the display when it happened. I had entered a command, and it timed out dues to open squelch, reported that in the receive pan then immediately aborted.
Anything I can look for to help troubleshot this issue?
|
Is that a question? Call Sign KQ5DX Email bobgroselle@... or bob.groselle@...
On Sunday, January 5, 2025 at 01:12:46 PM CST, Robert Hadley, K9TWC via groups.io <rhadley06@...> wrote:
Requesting membership. No email with call sign.
|
Requesting membership. No email with call sign.
|
Thanks Steve
Did a git pull & build of 4.7 and 4.2.06.19 is now most
happy!
Cheers Bob VK2YQA
On 5/1/25 15:55, Steve, KB5AW via
groups.io wrote:
toggle quoted message
Show quoted text
Compiling fldigi with Hamlib 4.7~git may have been resolved.
?
On Jan 3, Hamlib made this change:
#define RIGCAPS_NOT_CONST 1
// As of
2025-01-03 removeing this -- fldigi was the only one that
got it right
//
riglist_foreach is now constant again but others are not
// #define
RIGCAPS_NOT_CONST 1
?
RIGCAPS_NOT_CONST
should be removed now because rig_caps has been reverted to
type const.
This was still in place after
rig_caps was reverted to type const, causing fldigi to fail.
?
I installed the latest Hamlib
4.7~git and reinstalled fldigi 4.2.06.19 successfully.
It is working and now listening to
the ARRL RTTY roundup.
_._,_._,_
|
Dave, W1HKJ
Philip Rose, GM3ZZA
Drew, KG7YSX
Ron NY3J