开云体育

Is there anything more I can add to help with troubleshooting?

It has been ages since I setup CUPS for that! From memory one has to "Allow" the LAN addresses in /etc/cups/cupsd.conf (defaults to localhost), but I would expect that is all configurable via the

Thanks to all that responded.? Switching to Firefox allowed me to use the CUPS website and I can use the printer on USB again (USB conned to the Pi).? I still can't figure out how to use the printer

The Country (CTY) Files were updated on 22 December 2024: https://www.country-files.com/cty-3440-22-december-2024/ For installation instructions, start at:

is posted at http://www.w1hkj.com/alpha/fldigi/ * fldigi-4.2.06.16.tar.gz <http://www.w1hkj.com/alpha/fldigi/fldigi-4.2.06.16.tar.gz> * fldigi-4.2.06.16_SO.dmg

I mentioned in my previous post that the X6200 creates two sets of two ports (two "cu.*" ports and two "tty.*" ports). Previously, the higher numbered tty.usbmodem port was the one that was working.

Hello, On my Linux installs, whether ARM or Intel hardware, I dump Chromium. I run Firefox instead. I have no problem running CUPS. Cheers, Robert KG4KGL

Here's a follow up to the Fldigi lockup problem. So I'm now using Ubuntu 24.04. Tonight on a local FM repeater NBEMS net I was so happy because everything was working great. There was a lot of

Thanks for the response! In the case of the X6200, it shows 4 ports. Two "cu.*" ports and two "tty.*" ports. The correct ones to use with the X6200 are the tty ports. And they never appear to flip (or

lsof from homebrew can verify that: $ lsof /dev/cu.* COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME flrig 45225 arekm 9u CHR 9,5 0t0 12413 /dev/cu.SLAB_USBtoUART flrig

I've had flrig working on my MacBook Air (M2, running macOS 15.2) for a few days with my Xiegu X6200 (using the X6100 rig choice in prefs). With the exception of needing to reboot between usages of it

Hello John, This certificate would be at the OS aka system-wide level. To be honest, I would just recommend to accept the self-signed certificate for home internal uses. If you really don't like

Hi David, Is the certificate something I must install or is it something the CUPS web server must install? John

Workaround/solution found.? Open .nbems folder, see file names FLMSGprefs.? delete that file.? When you restart FLMSG you will have to reconfigure your call sign and other configuration settings

I had to do a rebuild and can't get fldigi to control my FTDX10. Radio works fine using CAT in WSJT-X so I know USB communications will work. I am getting a good waterfall in Fldigi and PSK31

Hi David, Thanks for getting back to me. Attached is the trace.txt file with the settings shown above. I do have polling enabled in the settings and perhaps the polling rate is set too high, but I

Hello John, This is probably due to Chromium insisting on using HTTPS but CUPS is using a self-signed HTTPS x.509 certificate. You can either choose to tell Chromium to trust and accept this local

I had cups running OK on an SD card before I switched to an NVMe device and mistakenly managed to overwrite my SD card.? I started over and am now running only on the official Pi NVMe ssd . Using

Dave, Here is a curiosity question: I am running the current alpha code (4.2.06.15) now, but have seen this multiple line blurring effect going back a ways in previous versions. If I run fldigi on

The objective is to open a previously-received file and relay it.? I cannot open a file from file | open. file | folders, double click on a file - file opens in mousepad but not in the FLMSG