开云体育

Hi David, Thanls for answer. I understand what you mean, I'll work in this way and I'll come back. Regards

Pedro, If you experience tuning only one band or frequency, this might be a problem of coax wavelength. The coax feeding into the tuner might be a harmonic frequency which causes the radio signal to

Dear all, I have dete4cted one probolem i have working at 40m. I have an LDG AT100ProII and IC7300. Always tuning with 10wats. the tuner always tune at moment by the memories except at part of the

Hi Mark I have the at100proii and i thing both work at same way: The tuner tunes the antenna to an swr less than 1.7 but? ot always the minimum swr and you can manually adjust the swr to 1.1. Some

I have an AT200 Pro (not Pro II). I know the threshold setting determines the maximum SWR the tuner will detect before it begins a tuning cycle. ?Does it also set a "minimum" target SWR? That is, If

Ed; Name is Joe, Call here is K4SAT. I am planning on upgrading to general, I was big into Hamsats in past years and now planning a road trip and new vehicle in 2021 so I want to equip for 10 and 6 FM

Ed; Name is Joe, Call here is K4SAT. I am planning on upgrading to general, I was big into Hamsats in past years and now planning a road trip and new vehicle in 2021 so I want to equip for 10 and 6 FM

To the original poster (rhyolite ? ... name and callsign would be nice) ... I just checked my manual and found this under specifications: ".1 to 125 watts SSB and CW peak power, 30 watts on PSK and

If I remember correctly, the Z11ProII isn't rated for 100 W continuous (FM), so that might seem to eliminate it at the outset. Regards, --Kirk, NT0Z My book, "Stealth Amateur Radio," is now available

I like my AT-200Pro II but have not used or read up on the Z-11Pro II . and really can’t give you much advice on mobile HF antennas. I mostly am on 160 meters after 10:30PM most nights except when

I am considering purchase of ether AT-200ProII or Z-11ProII for use in an SUV equipped with a Motorola Syntor X9000 radio. I desire to tune 29-54 MHz contiguously to include Ham part 97 and Itinerant

Hi Kevin, You can take a look at this f.i. https://www.amazon.com/RP-235-Adjustable-Universal-Mounting-Scanners/dp/B001JT5PH4?ref_=d6k_applink_bb_marketplace Regards Pedro ea3fnm Barcelona

I remote mounted my 857 body so I just used some large hose clamps to clamp my z11pro to the body of the 857. You could do the same thing with the AT100 as it is about the same size as the 857 body.

Does anybody know of mobile mounting bracket that would be compatible with this tuner? Thanks. Kevin AD0IM

I have an excellent impression of the technical service. Today I replaced the PIC with the new firmware and the problem was solved. Thank you Dwayn so much!

Dear all, I come back with this issue because I have found the replay I'm lookng for the LDG in other tuner, The MFJ993 has this information in its manual page 16 table 1. Please see attached file

Update: LDG reports that they "recalibrated the unit" and have sent it back to me. ?I should have it for the weekend. Hopefully, my ATPro 200 will now tune on 80m and 6m, just like my Z100+ can!

More and more, I tend to think the AT200Pro will be found to have some issue. I connected my MFJ analyzer directly to the feed-point of the antenna ... As you can see, without any tuner, the SWR on 80

FYI Everyone - I did the full reset on the AT200Pro of holding down the three buttons, while applying power through the DC 12V plus in the back ... It did reset! No help. :-( I still get "all the SWR

I just found this on the LDG FAQ page: There is no way to reset all the memories at once. They are overwritten each time you perform a full tuning cycle on the frequency associated with the memory. So