Re: Y-acc-2 or y-acc-3 cables for ldg 200 pro II
If they are not available where you want to buy them, your remaining options are wait until they are in stock, do without, build your own or where ever you found the scalper prices - try to make a deal. ? Phil Laird, WI5O
"Never look a gift horse in the mouth."
toggle quoted message
Show quoted text
On Mar 14, 2023, at 03:03, fullauto54@... wrote:
?I don't understand why anyone would pay scalper prices for this item. On both Gigaparts and DX they will sell for under $13 and, even though they too are sold out, they sell for $10 on LDG's site. I need two of the one for my FTdx10 and FDdx1200, but I refuse to pay 4x's the selling price from a reputable company. The one I found states a 10 pin DIN yet the manual for both radios indicate it is a 8 pin DIN,I even went so far as to check the radios and YES it is a 8 pin DIN not 10 pin DIN for the tuner. The 10 pin DIN is for the linear Amp on both radios.
|
Thanks for the reply. Where is the fuse? I can't find it in the schematic. Yes, there are 13 volts on the regulator input.; moreover, touching the strip that connects the LED card with the motherboard, all the LEDs light up randomly...maybe the EPROM has been erased???
|
is there a fuse inside the tuner, maybe you missed??? ?did you check the 7805 with a voltage check?? do you have the 13 volts on the primary side of the regulator, or is it lower
Dave Garber VE3WEJ / VE3IE
Hello everyone. I have an AT100 pro II that suddenly stopped working and won't turn on anymore. It does not cycle through the LEDs on startup and does not respond to any key presses. I checked with the tester the L7805CV voltage regulator which supplies 5 Volts. The diodes look ok. Suggestions? Thank you.
|
Re: Y-acc-2 or y-acc-3 cables for ldg 200 pro II
I made my y-acc-3.? ?Use a db15 male connector and a 3.5 mm speaker plug.? tip goes the pin 11 and ground goes to pin 3.?
|
Folks,
years ago, when I bought the RT100 I prepared a Bias-T as per the Rev.
C of the manual, where the power was applied continuously to the
tuner.
While reviewing the schematics (v 1.2) posted on the new Zip file on
the Files section, I see the power is applied only by request, using a
pushbutton.
Should I update my Bias-T box? Is there any negative impact on the tuner?
Inquiring minds wanna know.
jon, ea2sn / ae2sn
|
Hello everyone. I have an AT100 pro II that suddenly stopped working and won't turn on anymore. It does not cycle through the LEDs on startup and does not respond to any key presses. I checked with the tester the L7805CV voltage regulator which supplies 5 Volts. The diodes look ok. Suggestions? Thank you.
|
Re: Y-acc-2 or y-acc-3 cables for ldg 200 pro II
I don't understand why anyone would pay scalper prices for this item. On both Gigaparts and DX they will sell for under $13 and, even though they too are sold out, they sell for $10 on LDG's site. I need two of the one for my FTdx10 and FDdx1200, but I refuse to pay 4x's the selling price from a reputable company. The one I found states a 10 pin DIN yet the manual for both radios indicate it is a 8 pin DIN,I even went so far as to check the radios and YES it is a 8 pin DIN not 10 pin DIN for the tuner. The 10 pin DIN is for the linear Amp on both radios.
|
Re: Y-acc-2 or y-acc-3 cables for ldg 200 pro II
Opps!! Miss read the manual . . . sorry. But still won't pay 4x's the price for them.
|
Re: RC/RT-600 Memory Tune Oddity
But wait, there's more.....
On power up, the RT-600 will not tune upon application of RF power, nor will it retain the last good tune.? The SWR is always high right after powering up.? It is as if it always powers up in bypass, and I have to initiate a full tune cycle.? After I do the full tune it operates as expected.? I am receiving 12 volts from my Icom PS-125.
|
Got it too.? I don’t need it – NOW.? But I have two RT-100s here, neither being used right now…….. and it may come that I need a schematic someday.
THANKS EVERYONE !!! ? ? Vy73? –? Mike? –? KD5KC – WRFF851 –? El Paso – Texas? –? DM61rt.? SOTA W5T-Texas Association Manager. ? The canyons are calling, colorful and deep.? But I have promises to keep. And miles to go still in my Jeep...?? And miles to go still in my Jeep... ? 
? ADVENTURE:? The respectful pursuit of trouble.?? An EXIT is really an ENTRANCE to someplace new.? It isn’t an ADVENTURE until something goes wrong! ? ? ?
toggle quoted message
Show quoted text
From: [email protected] < [email protected]> On Behalf Of Dennis McKinney N0SMX Sent: Saturday, March 11, 2023 19:12 PM To: [email protected]Subject: Re: [ldgelectronics] RT 100 schematic ? Thanks a million AL.? Found what I needed... ? On Sat, Mar 11, 2023, 5:51 PM Al Waschka <awaschka@...> wrote: The schematic is in the Files Section on here. ? Al K5TAN ? ? ? Mike? thanks but I have the manual also. I bought this tuner new in 2016.. If I find a schematic I'll share it with you.. Mostly what I'm finding out is non exist for public distribution.... ? On Sat, Mar 11, 2023, 3:15 PM Mike Olbrisch <mike-2020@...> wrote: I have the manual in .PDF, I’ll share if you need it.
I have no schematic.? If anyone does and will share…..? Please—ME TOO! ? ? Vy73? –? Mike? –? KD5KC – WRFF851 –? El Paso – Texas? –? DM61rt.? SOTA W5T-Texas Association Manager. ? The canyons are calling, colorful and deep.? But I have promises to keep. And miles to go still in my Jeep...?? And miles to go still in my Jeep... ? ? ADVENTURE:? The respectful pursuit of trouble.?? An EXIT is really an ENTRANCE to someplace new.? It isn’t an ADVENTURE until something goes wrong! ? ? ? ? Does anyone have a schematic for the LDG RT 100 remote tuner. I have an issue with mine and found a burned resistor on the board.? I can't determine the valve to replace it with..
Thanks in advance
Dennis N0SMX?
|
Thanks a million AL.? Found what I needed... Dennis N0SMX?
On Sat, Mar 11, 2023, 5:51 PM Al Waschka < awaschka@...> wrote: The schematic is in the Files Section on here. ? Al K5TAN ? ? ? Mike? thanks but I have the manual also. I bought this tuner new in 2016.. If I find a schematic I'll share it with you.. Mostly what I'm finding out is non exist for public distribution.... ? On Sat, Mar 11, 2023, 3:15 PM Mike Olbrisch <mike-2020@...> wrote: I have the manual in .PDF, I’ll share if you need it.
I have no schematic.? If anyone does and will share…..? Please—ME TOO! ? ? Vy73? –? Mike? –? KD5KC – WRFF851 –? El Paso – Texas? –? DM61rt.? SOTA W5T-Texas Association Manager. ? The canyons are calling, colorful and deep.? But I have promises to keep. And miles to go still in my Jeep...?? And miles to go still in my Jeep... ? ![]()
? ADVENTURE:? The respectful pursuit of trouble.?? An EXIT is really an ENTRANCE to someplace new.? It isn’t an ADVENTURE until something goes wrong! ? ? ? ? Does anyone have a schematic for the LDG RT 100 remote tuner. I have an issue with mine and found a burned resistor on the board.? I can't determine the valve to replace it with..
Thanks in advance
Dennis N0SMX?
|
The schematic is in the Files Section on here. ? Al K5TAN ? ?
toggle quoted message
Show quoted text
From: [email protected] < [email protected]> On Behalf Of Dennis McKinney N0SMX Sent: Saturday, March 11, 2023 3:37 PM To: [email protected]Subject: Re: [ldgelectronics] RT 100 schematic ? Mike? thanks but I have the manual also. I bought this tuner new in 2016.. If I find a schematic I'll share it with you.. Mostly what I'm finding out is non exist for public distribution.... ? On Sat, Mar 11, 2023, 3:15 PM Mike Olbrisch <mike-2020@...> wrote: I have the manual in .PDF, I’ll share if you need it.
I have no schematic.? If anyone does and will share…..? Please—ME TOO! ? ? Vy73? –? Mike? –? KD5KC – WRFF851 –? El Paso – Texas? –? DM61rt.? SOTA W5T-Texas Association Manager. ? The canyons are calling, colorful and deep.? But I have promises to keep. And miles to go still in my Jeep...?? And miles to go still in my Jeep... ?
? ADVENTURE:? The respectful pursuit of trouble.?? An EXIT is really an ENTRANCE to someplace new.? It isn’t an ADVENTURE until something goes wrong! ? ? ? ? Does anyone have a schematic for the LDG RT 100 remote tuner. I have an issue with mine and found a burned resistor on the board.? I can't determine the valve to replace it with..
Thanks in advance
Dennis N0SMX?
|
Mike? thanks but I have the manual also. I bought this tuner new in 2016.. If I find a schematic I'll share it with you.. Mostly what I'm finding out is non exist for public distribution....
Dennis N0SMX?
On Sat, Mar 11, 2023, 3:15 PM Mike Olbrisch < mike-2020@...> wrote: I have the manual in .PDF, I’ll share if you need it.
I have no schematic.? If anyone does and will share…..? Please—ME TOO! ? ? Vy73? –? Mike? –? KD5KC – WRFF851 –? El Paso – Texas? –? DM61rt.? SOTA W5T-Texas Association Manager. ? The canyons are calling, colorful and deep.? But I have promises to keep. And miles to go still in my Jeep...?? And miles to go still in my Jeep... ?
? ADVENTURE:? The respectful pursuit of trouble.?? An EXIT is really an ENTRANCE to someplace new.? It isn’t an ADVENTURE until something goes wrong! ?
? ? Does anyone have a schematic for the LDG RT 100 remote tuner. I have an issue with mine and found a burned resistor on the board.? I can't determine the valve to replace it with..
Thanks in advance
Dennis N0SMX?
|
I have the manual in .PDF, I’ll share if you need it.
I have no schematic.? If anyone does and will share….. ?Please—ME TOO! ? ? Vy73? –? Mike? –? KD5KC – WRFF851 –? El Paso – Texas? –? DM61rt.? SOTA W5T-Texas Association Manager. ? The canyons are calling, colorful and deep.? But I have promises to keep. And miles to go still in my Jeep...?? And miles to go still in my Jeep... ? 
? ADVENTURE:? The respectful pursuit of trouble.?? An EXIT is really an ENTRANCE to someplace new.? It isn’t an ADVENTURE until something goes wrong! ?
?
toggle quoted message
Show quoted text
From: [email protected] < [email protected]> On Behalf Of Dennis McKinney N0SMX Sent: Friday, March 10, 2023 11:15 AM To: [email protected]Subject: [ldgelectronics] RT 100 schematic ? Does anyone have a schematic for the LDG RT 100 remote tuner. I have an issue with mine and found a burned resistor on the board.? I can't determine the valve to replace it with..
Thanks in advance
Dennis N0SMX?
|
Re: Y-acc-2 or y-acc-3 cables for ldg 200 pro II
I have found some of these cables on eBay. Your mileage may vary.? Phil Laird, WI5O
toggle quoted message
Show quoted text
On Mar 11, 2023, at 12:47, Gregg Schulz <W9awx1@...> wrote:
?Still on a national backorder.? No ETA from LDG as to when they may become available.? You may see some dates listed on some of the retailer websites but that is generally just an computer algorithm estimate, not anythign from LDG saying it will be available by the date listed.
|
Does anyone have a schematic for the LDG RT 100 remote tuner. I have an issue with mine and found a burned resistor on the board.? I can't determine the valve to replace it with..
Thanks in advance
Dennis N0SMX?
|
Re: Y-acc-2 or y-acc-3 cables for ldg 200 pro II
Still on a national backorder.? No ETA from LDG as to when they may become available.? You may see some dates listed on some of the retailer websites but that is generally just an computer algorithm estimate, not anythign from LDG saying it will be available by the date listed.
|
Re: correct cable for FDX3000
I would also like to use a LDG 1000 with a FTdx 3000 but would like to use the TUNER port on the radio instead of the LInear (15 pen) port.?
|
Re: Cable for FTDX10 + Z11-Pro 2
did you go into the operation settings and change the internal tuner settings??
Dave Garber VE3WEJ / VE3IE
On Wed, Mar 8, 2023 at 8:42?PM JeffH - W4JEW < jeff@...> wrote: Hello,
I'm back with some additional questions about EXPECTED behavior vs ACTUAL behavior. I built the cable I shared the schematics for a few weeks ago. I thought it was working properly, but I'm starting to question myself and whether or not the cable I built is working as it should be.
My friend just bought an AT200ProII tuner. We were reading through the documentation, which covers using a cable between the tuner and the radio for Icom and Yaesu radios.
We both have FT-DX10 transceivers - the only difference is he's running the AT200ProII, and I'm running a Z11ProII.?
Whenever we pressed the Tuner button on the front of the DX10, we thought it initiated a tuning cycle on the LDG. I just moved the tuner away from the DX10 and tried using the Tuner button, and I can clearly hear the tuner relays inside the DX10 running.
And yes - we both have the External tuner option selected in the DX10 menu - and the radios have been restarted (multiple times).
The documentation states:
"A tuning cycle on the AT-100ProII is initiated from either the Tune button on the front of the AT-100ProII, an over-SWR condition when in fully automatic tuning mode, or from pressing the TUNER/CALL button on the front of an ICOM radio connected using the ICOM interface cable."
"If you are using the ICOM or Yaesu interface cable, your radio will automatically reduce power, switch to CW mode, and transmit for as long as is needed to complete the tuning cycle, and then will return to the previous operating mode and power level when done.?"
If I am interpreting this correctly, it's implying that using the Tuner button on an Icom radio will initiate a tuning cycle on the LDG tuner but pushing the tuner button on a Yaesu radio will not initiate a tuning cycle on the LDG.
That being said, the benefit of using the cable between a Yaesu radio and an LDG tuner is that you don't need to reduce power or change to AM/CW mode. I'm unsure how to confirm if this is happening, though.
Please help.
Thank you,
-JeffH
|
Re: Cable for FTDX10 + Z11-Pro 2
Hello,
I'm back with some additional questions about EXPECTED behavior vs ACTUAL behavior. I built the cable I shared the schematics for a few weeks ago. I thought it was working properly, but I'm starting to question myself and whether or not the cable I built is working as it should be.
My friend just bought an AT200ProII tuner. We were reading through the documentation, which covers using a cable between the tuner and the radio for Icom and Yaesu radios.
We both have FT-DX10 transceivers - the only difference is he's running the AT200ProII, and I'm running a Z11ProII.?
Whenever we pressed the Tuner button on the front of the DX10, we thought it initiated a tuning cycle on the LDG. I just moved the tuner away from the DX10 and tried using the Tuner button, and I can clearly hear the tuner relays inside the DX10 running.
And yes - we both have the External tuner option selected in the DX10 menu - and the radios have been restarted (multiple times).
The documentation states:
"A tuning cycle on the AT-100ProII is initiated from either the Tune button on the front of the AT-100ProII, an over-SWR condition when in fully automatic tuning mode, or from pressing the TUNER/CALL button on the front of an ICOM radio connected using the ICOM interface cable."
"If you are using the ICOM or Yaesu interface cable, your radio will automatically reduce power, switch to CW mode, and transmit for as long as is needed to complete the tuning cycle, and then will return to the previous operating mode and power level when done.?"
If I am interpreting this correctly, it's implying that using the Tuner button on an Icom radio will initiate a tuning cycle on the LDG tuner but pushing the tuner button on a Yaesu radio will not initiate a tuning cycle on the LDG.
That being said, the benefit of using the cable between a Yaesu radio and an LDG tuner is that you don't need to reduce power or change to AM/CW mode. I'm unsure how to confirm if this is happening, though.
Please help.
Thank you,
-JeffH
|
Paul St. John
Mike Olbrisch
Dennis N0SMX The Villages, FL
Gregg Schulz
JeffH - W4JEW