开云体育

Anyone have a working email address for Palstar. The 2 one the website bounce back. Steve? W7CM

Philip, Thank you very much for your input.. I'll give the K4D more thoughts.. just wish that Elecraft would implement analog-looking meters (like those on my FTDX101D) in their K4

Hi Barry, for instance my KPA500 works perfect at 600 watts, swr does not move. My DL is too small, i will need to get a bigger one. I have the previous FW, i will update it. Issue exists only in

Ray I like it a lot. My dream is to have a kpa1500 but I need near 10K to put one of those here in Chile. 73, Philip

The LA-1K, by design, switches to standby at every band change.? From the /Fault and Display Notifications/ page: This is reiterated in the notes to firmware version 1.08S (current online

My LA1K ,Which is set to standby at startup , Switches back to standby on the very first key up. SWR Is 1.2 into a Buckmaster 6 to 80. Radio is a 7610. I touched standby and it goes back to operate

Philip, When you say using any other AMP, what are those amps? Are they also Solid State? Tube amps can go pretty much thru anything without obvious happenings, Solid State not so much. The LA1K

Hi Philip, CE4PS, how do you like your Elecraft K4D?? Thinking that it might pair even better with my Elecraft KPA1500. 73 Ray KJ5MI

Hi Barry txcvr is an Elecraft K4D, voltage is 220V, antenna is flat swr. No big dummy here. 73, Philip CE4PS

Hello Ron, unfortunately I don't have a 1K dummy load to test, but antena is 1.2 1.3 max. Other linear do not trip or make SWR jump. Measurements made also with a LP-100A. 73,

Need more info, Yaesu FTdx5000 has a known issue. What is your txcver model? What is the voltage supply? 220/120 Did you test on dummy load? 73 Barry VE6UM [email protected]> wrote:

How does the amp test on a dummy load? Ron WD8T Sent from Proton Mail Android

Hello I have a M2 KT36XA flat on the 3 bands. When I use the LA1K on CW with more than 180 watts, it trips, SWR start jumping. Using any other AMP is no problem. Any ideas? Cheers, Philip CE4PS

You really only need your keying cable and nothing else. That’s one wire and t RCA plugs usually Sent: Saturday, August 31, 2024 7:02 AM To: [email protected] Subject: Re: [la1k] FT710 to LA1K The

Here is a keying cable is you just want to use RF sensing. https://www.ebay.com/itm/325343335857 Here’s the cable you need for keying and band

James ... Additional information you will need and decisions you need to make: _Question 1:? Do you intend to operate CW with your LA-1K?_ If so, choose DIRECT keying mode in the LA-1K, but

Dear Group: Attached should be a short pdf document with details. Version One. Others are encouraged to provide details about connecting their transceiver. Thanks for assistance provided. 73

The company Associated Radio makes cables to interconnect between rigs and the LA-1K, if you need a cable that is not listed I believe that they will make one for you. www.associatedradio.com -- Glen,

At last, some useful assistance. Many thanks. It is possible that the "band cable" that I have will perform all of the needed tasks. Need DB9 pin 7 to go to ground when transmitting, and need to

I was sold a "band cable" that is thought to connect to the 8 pin "Tuner/Linear" port on the F710 (upper left on the back) and that it will supply band information to LA1K when the other end is