开云体育

The Yauesu data cable for the Ameritron AL-1306 works perfectly with my 101D. AMERITRON DB-DB15Y Ron WD8T Sent from Proton Mail mobile

Bill, I searched the Palstar website and don't find this band data cable.? Where did you get yours from? I have a FT-991A and LA-1K and this would be nice to have. -- Glen, WB4KTF, Austin,

Good news to share: ?My LA – 1K amplifier was sending no power out and was not band switching as it had previously done successfully for months. I replaced the Palstar LA-1K to yaesu band data

Steven N7NF Did you find the power problem? This same issue has occurred with my Palstar LA-1K (which was working perfectly). Bill AG5ZN

Hey Kent K9ZTV, My bad.? If I had read the 4-Dec-2023 post /g/la1k/message/1469 by Claus (AE0S) all the way to end of his post, I wouldn't have wasted your time yesterday asking you

Kent K9ZTV, so sorry in my post yesterday /g/la1k/message/1474 I neglected to address the first two (2) sentences of your post, stating that " The 33 amp statement applies only to the

So glad to see that you have responded as to the identity of the manual in question, Kent. 1.? To be accurate, the "33 amp" information you referenced in the online manual

The 33 amp statement applies only to the maximum current rating when using the amp on 120 VAC.? That's not its nominal draw, that is the maximum that the amp can tolerate.? Above 33 amps and the

The 33 amp statement applies only to the maximum current rating when using the amp on 120 VAC.? That's not its nominal draw, that is the maximum that the amp can tolerate.? Above 33 amps and the

Rick VE3PP, Have you brought Kent's insights /g/la1k/message/1467 about the LA-1K power supply to Mr. Mark Ward's attention at Palstar? 73 Ray KJ5MI

Claus, Please be advised the currently available LA-1K Technical Manual https://www.palstar.com/en/product-manuals/manual_la-1k.pdf *doesn't apply* to LA-1K?with a serial number (S/N) higher than

Thanks to being licensed we know: P = U * I so 120V * 15A = 1,800W 240V * 10A = 2,400W We remember that legal limit is 1,500W, although the LA-1K should only be run up to 1,000W. Some power goes out

I was assured by the Palstar Tech rep that the amp does not draw anywhere close to 33 amps on 120 V. The sticker on the back of the amp under the power cord states 20 amps and I was told it would not

Hey Kent, Thought I'd follow up with you after getting no response to my posts /g/la1k/message/1460 and /g/la1k/message/1461 regarding your insights on the LA-1K

This pre-release information https://icomuk.co.uk/files/icom/PDF/newsFile/IC-PW2_leaflet_at_Ham_Fair_2022.pdf makes claim that "The IC-PW2 has succeeded in realizing the world’s first DPD as a

The part of the Digital Pre-Distortion system in the amplifier is only a RF sampler (or attenuator) that provides a very small feedback signal from the amp to the transceiver. All the DPD work

The Palstar LA-1K incorporates a rear (RCA jack) labeled, and included in the instruction manual, as:: ? P U R E S I G N A L : S a m p l e @ + 1 0 d B m @ 1 k W o u p u t ( R e a r P a n e l ) I

Hi Thomas, Looking at this ICOM page https://www.icomjapan.com/lineup/options/IC-PW2/ it sure sounds like the DPD thing applies solely to their IC-PW2 amp when paired with their IC-7610

I am using an ICOM IC-7610 transceiver and ICOM has released a software update to provide DPD (Digital Per-Distortion) in addressing non-linearity in RF power amplifiers. Is this something which

Kent, K9ZT, Were you referring to another version of the LA-1K manual from Palstar that has been revised to include specifications of the power supply installed in the LA-1K amps that are currently