开云体育

Bill, You should be seeing the id 7.3.7 in the logs. That says 'all systems' so JMRI lets that match any of the command stations. -Ken Cameron, Member JMRI Dev Team www.jmri.org

Yes, first and third were PowerCab and middle was SB5. All same profile, just changed the preferences. I put the jumpers back on the board, set it to 19,200 and it appears to be happier now.

Bill, I see three startups in the file. The first and third seem to be fine, but the second one has the problem. What was the settings in the connection for each of the three? To me, it looks like

No, sticky isn't "all very well for people using the group's web interface." That's exactly the problem - When you use the Web interface, the first page is stickies you have to scroll through to get

Here you go Ken, everything from today. I will re-install the jumpers and tweak the Advanced settings to 19,200 vs 9,600 baud. Bill Sent: Sunday, March 09, 2025 10:30 AM To:

Bill, That log didn't have the other run. The session.log gets reset every time you open JMRI. The messages.log is the last ### runs up a meg of file space. I think what would be best is a

Ken, There should be two sequences in there with the latter having it set for SB5 and resulting in the error. I have three throttles on the bus, my original power cab (with procan cable), a second

Brett, On Panel Editor it is straight forward. I used the SIM profile because I'm too lazy to pull my Power Pro out (I can if need be) First make sure that you can see your AIU and that its Cab

Looked at it and started to think about to do it, but I found that the SignalPilot has a lot of indexed CVs and, furthermore, there is no documentation about its CVs (all of them) :( , so,

Bill, This log looks normal. I don't see it showing any issue with opening the port, getting the id from the NCE USB. But what did you have set in the connection window at this time? I'm

Ken, I am currently using 5.11.3, but this problem existed on the prior released version as well. I have a “new” session log attached here for your review. My message log goes back to 2020 so it

https://www.jmri.org/help/en/package/jmri/jmrit/operations/Operations.shtml#PrintLocation Dan

Hello All After a year away im back into it,and starting to put layout into jrmi,thanks to all who devolop it. I have added sensors before and had them working but this time not so good Ihave all?

Sticky is all very well for people using the group's web interface. I don't, and I'm sure there are many like me who just let the messages arrive in email form, either individually or as

Doing that lists the messages singly, not threaded. Personally, I don't find that a useful format whatsoever. I agree with Andy - Move the stickies somewhere else, maybe leaving one sticky with a

Fr a given JMRI profile: "Edit"->"Preferences"->"Start Up". operate the "Add" button, and select "Load table content and panels...". Select the appropriate ".XML" file. "Save" the

Stewart, The version you showed is the Java version. The JMRI version will be 5.something. Edge Connector "links" are connections between two blocks. For example, Panel 1 :: track segment (block

Gents, Just wondering, where do I find the ‘track analysis tool’? I do not seem to be able to find it. Noel Sent: Sunday, 9 March 2025 7:50 AM To: [email protected] Subject: Re:

years ago i backed up my PowerPro command station into JMRI It copied any macros and other data from the command station to a file in JMRI. Now I can’t find it Could someone explain the process

Hi, I am developing two Layout Panels for my two-level layout. I have added an Edge Connector on each Panel for the connecting track between the two panels. When I try to "Edit Link" to connect the