开云体育

Steve, The WeMos D1 R2 also has two SPI buses: the hardware SPI bus (HSPI) and the software SPI bus (SSPI). For the WeMos D1 R2, the hardware SPI bus (HSPI) is connected to the following pins: SCK:

OK, so thanks for confirming the correct, working sketch for me. Now, I know that you wanted the same debugging functionality as in the Serial PN532 sketch, where the serial monitor tell you that

Tom Well, I really don't know what's happening today, I seem to get anything working much today! The Uno's seem to be connecting to the laptop, but they are not reading any tags at all, non of them!

To be clear, when you perform “Add Loco” with DecoderPro, JMRI presents you with a decoder selection that does not work when you accept the selection? -- Ken NYNH&H, Old Colony Division, Cape Cod

Thanks for your reply, Cliff. This newbie stumbled on solution.

MFRC522, Uno, Ethernet and Serial Tom, sorry for the delay in posting this sketch. I wanted to make sure it was the right one before I did so. As you may have guessed, I assign version numbers to

I am just wondering if 2 are been offered as the lights in one end without the motor and decoder still need to communicate as I’ve only fitted the 1 decoder on the motor and which housed the

You cannot actually run the locos on the programming track. (Yes the trains *might* move a little while reading CVs.) -- Robert Heller -- Cell: 413-658-7953 GV: 978-633-5364 Deepwoods

Recently bought two locos and whenever I put them on the programming track with JMRI, the trains only move incrementally backwards and selects multiple possible decoders (none of which work). Using

Well, I changed all the masts (about 35 of them) to a send count of 1 and the problem went away. That MIGHT have been the answer, or I did something different in the startup sequence, or it was

Are you using masts? If so, set the *Send Count* to 1, not 3. See how that works. -- Ken NYNH&H, Old Colony Division, Cape Cod Branch (1949-1959) [DB150][PR3][QuadLN_S][JMRI 5.3.5]

I have been working with my panels (current version at /g/jmriusers/files/ProblemsBeingWorkedOn/Scott_Waltons_problem/PRR_West_CTC_cleaned_fourth_reset.xml) (

Dear All, I have just placed my Bachmann MPV on the test track to let JMRI read the information to be able to add it to my Roster. I have fitted a Dapol Imperium1 21-pin inside and have been running

And I should apologize, as I may have miscommunicated in an earlier post when I said.. I should have pointed out that there are 2 detail Levels you can adjust.? Both are found in the?Trains

Blair, Not pot stirring at all! Lol! All useful comments. Looking at my test rig, it is a rats nest of jumper cables. They are easily disturbed and a bit confusing at times. I can't see anyone

Tom, Steve Here comes that pot-stirrer again.? What/who is the intended target for PCBs?? I agree, a discussion needs to be had about essential/wanted/desired features to put things into

For some reason my email server has lost all the jmri emails I saved. Also many other folders as well are empty. I want to find the info with links to the Arduino project that tells you how to setup

Steve, If the sketch works on the Uno, it will work on the Mega, which I can test here tonight or tomorrow. I spent a LOT of time ensuring the pin assignments are appropriate for all 3 board t

Thank you! So, the board that came with my loco had an internal dcc decoder on the big main board? I didn't even know that was possible haha. I am going to take your advice and just replace the main

Steve, As soon as you confirm for me the working MFRC522 Ethernet sketch, I can add the debugging messages and blinks. Tom