开云体育

Rummy, You did not do anything wrong. The SSL errors are common for people switching from signal heads and SSL to signal masts and SML (signal mast logic). It appears that you are using SE8Cs to drive

Hi Steve Todd, Since you created the JMRI for the Pi bundle. Can I upgrade my Pi 3 to a 4 by just moving the SD card to the 4 without problem? Or is that an unknown experiment I would have to try?

Dave, First, thanks a million. Second, dang you for busting my bubble! ?LOL I used the brute force method and it worked perfectly. ?The panel opened with no errors in the system console, all LRoutes

Thanks for the suggestions as to how I can look further into my Logix failure between JMRI 4.21.4 and 4.21.5. I have uploaded the full Panel File <Graubünden-21-0313 Debug prep.xml> to the Problems

Norb, A fix has been submitted and should be in the 4.23.3 test release. Dave Sand

Dell i7 laptop, Win 10? (Firewall disabled), Digitax DCS 210 Command Station, (2) Digitrax DB210 boosters, (5) Digitrax DS64, (2) Digitrax BXP 88, Digitrax UR92, Digitrax PR4, JMRI 4.16 Previously

Ken, First note that you're wanting to autostart a GUI program once the desktop loads. This is not the same thing as autostarting a program at bootup (I know you didn't use those words, but wanted to

Steve, For the ones that reappear, use the context edit menu and verify that the arc angle is not set to zero. If it is, the hide option is not stored. There was a bug that set new arcs to 90? but

I have a similar problem in the previous version. I hide construction lines, store the panel and next time I open the panel the construction lines appear again. Seems to happen on the same curves all

Phil How I have done it its as follows. When train arrives at end. Sets 13Yard-ArrivedFrom0810 active.(in transit actions when train stops) . . It must terminate at end. Have a logic that runs

Thanks Norb. I was going to report the same issue in the latest update to 4.22. I do note that you can individual hide track construction lines by right clicking on the construction point and

Rummy, The BlockBoss errors are caused by leftover SSL definitions. The only official way to clear the errors is to delete the related signal head table entry. Since your signal masts are defined as

File moved to: /g/jmriusers/files/ProblemsBeingWorkedOn/rummy -- Peter Ulvestad *Think before you post, try to be positive, and you do not always have to give your opinion.....* JMRI

rummy@... added folder */ProblemsBeingWorkedOn/Ron Rumberger*

First let me reiterate: ?I really appreciate all you guys do to keep the rest of us moving along with JMRI! System Console: 2021-03-13 07:37:29,231 util.Log4JUtil ? ? ? ? ? ? ? ? ? ? ?

The following files have been uploaded to the Files area of the [email protected] group. * /ProblemsBeingWorkedOn/Phase 4b1d.xml ( /g/jmriusers/files/ProblemsBeingWorkedOn/Phase

Hi Steve Thanks for the information. Are there plans to address this scenario in the future? Is there any other way to accomplish this movement? Thanks again Phil

Hi Phil See /g/jmriusers/message/186054 for a better idea as FWD and REV means. You cannot change the direction of a locomotive in the middle of a transit. The FWD and REV are not

I have a train that pulls out the siding goes around the layout and is supposed to back into the same siding. I can get the train to pass the siding but will not reverse. The section before the

Rummy, A LRoute is actually a Logix. The LRoute table Add/Edit window provides an alternate GUI for creating the Logix. Any issues with LRoutes running are actually Logix issues. When you update the