开云体育

I tried this second method and I got the same invalid message. I did see what the problem might be though. When comparing the original target script to the replacement script I noticed that (x86) was

Patrick: From your description it sounds like JMRI is controlling trains on your layout but that you are unable to get one specific loco to respond to control via its speed table. Is that correct? If

Browsing his older post, he reported same (if not similar) issue in June 2018 but never reported if issue was resolved.? He was getting long list of errors and it was suggested he rebuild roster

Hi Dave, The Stack Overflow is caused by a LE Turnout being paired in 2 different panels, have raised https://github.com/JMRI/JMRI/issues/7456 to discuss this, Steve.

Thanks to all who have read this thread and particularly those who have contributed. A great exercise and I have learnt a lot from it. Just to finish off, I have gone to single sensor inputs the

Conrad, I have now created a change request regarding HALF_SPEED, see https://github.com/JMRI/JMRI/pull/7455 Klaus

Am 26.09.2019 um 00:25 schrieb Charles Meo: <snip> Thanks for the test. I also tried the doubling method, for notch1 and notch2. I didn't change the rpm thresholds. The chuffs are coming as expected.

Rick, You can install Java 8, update 151 on XP, provided you use the workaround procedure described at: <http://jmri.org/install/WindowsNew.shtml#sysreq> That may not fix your problem, but it will

Am 25.09.2019 um 22:31 schrieb conrad: Conrad, your math is correct. If you want to allow 420rpm you can do that. But it's better then to use appropriate sound files. Class64.vsd doesn't sound good

Bob, It was a good idea, but didn't help.... I downloaded the latest EasyDCC system manual from the CVP Products website. Set the Command Station default speed step value to 28 (choice 2). Pressed ESC

Don Setup Key #6 then #2 ESC Down load the manual from the CVPUSA web site. Gerry -- Gerry Hopkins MMR #177 FNMRA Great Northern Downunder http://www.greatnortherndownunder.com

1 - Right Click on existing DecoderPro Icon 2 -? Select copy. 3 -? Now move cursor over to blank spot and Right click . 4 - NOTICE the are two PASTE options? available. PICK? PASTE SHORTCUT 5 - We

Hi Marc, I have redone my loco with the Extended Series and now can adjust the CV's. Thanks again for the heads up Peter [email protected]> wrote: -- *Peter Beckett* PO Box 381 Hastings Victoria

Thanks, Bob. It would be great if that fixes my problem! I must need a newer manual. Mine was printed 3/27/2000. I looked at the index and thumbed through all the promising parts. Nowhere was there

Hi Marc, Thanks for that info. I was only looking at the SDXH186MT and did not realise that the Extended Series covered it as well Peter

CV169 is listed in the Extended series6 definitions added by John McMasters back in 2015 Marc

Hi Steve, I closed the throttle of the locomotive and changed the controller to a different address. Before that, I checked that the engine responded to turning on the headlight. I also closed the

I notice that Digitrax only list up to CV157 in their specs and JMRI lists up to CV160. However using Digitrax Soundloader program, one can go higher. Is it possible to get an update as I am

Hi Patrick. Firstly: It will not work if there is a throttle in use for that loco anywhere, jmri or wifi or what ever. Secondly: Don't try starting at 1, increment by 1, it will take all day and if

When I try to make a custom shortcut for the legacy interface by copying and pasting the new target script I get a pop up window that says what is in the target box is not valid – to make sure the