开云体育

Frank, My DCC command station is the NCE PH Pro 5 amp system. I purchased a Power Pax to program the newer sound decoders and it seemed to do the job for a while, but eventually I put it away and

Hi Jim ...YES...YOU GOT IT....That is Exactly what I am experiencing. ?YES, I think there was an update on the android software. ?I (hopefully) will check with the author of that software. ?THANK

FYI, I also never received and email from the group, with a person name Dick on it Thank Dave In PA Sent from iPhone Xs Max

Hi Dave Sorry for the delay, been sick. I am confused on your last reply, see below about a ground loop. My Assy. Bus is power by a separate external power supply, unrelated to my DCC power system. My

Frank, Get a 16-18VDC power supply for your PR3. I use an 18VDC 1.1 amp power brick salvaged from an old inkjet printer.? Then get rid of the Power Pax. You won't need it. My PR3 with that 18VDC

Frank, Get rid of the Power Pax and use a PTB100. The PS14 is enough power though I have a 16 volt on mine. David Klemm Sent from my iPhone Xs Max ________________________________ Sent: Monday,

Frank, There is a power supply available from Digitrax as I got mu PR3 with the optional power supply. Paul

I had my Pi's before I got into JMRI. I was just using my DCC system standalone. I got my Pi's (2, 3B and 3B+) to get back into Linux. I installed various HATs. Then I found out about JMRI and tried

Marc, I played around with audio feedback only on my BLI centipede, which I had already finished reading at that point. I’m away from my computer for a few days but will report back by next weekend

Hi Dave, as soon as I hit "update" to the section, and have the message log open, i get a long-winded error. It also throws up a window with the same error. I can provide a screenshot, however the

I think this is fixed by PR 7427 (https://github.com/JMRI/JMRI/pull/7427), but I don’t have hardware to check it. If anybody can build that branch and test with hardware, I’d be grateful.

Hello All I have learned that I cannot program any engines w/ JMRI on my program track.? JMRI works fine when I program on the main. I believe my PS14 power supply (with a Power Pax) is to low Can

Frank: As promised... Using my tablet I found a place where I lose signal so I see that the message I see that as "no signal, trying to reconnect" but it also includes your "is WiThrottle

I can recreate this. Will try to figure out what’s going on. Bob

Marc, Sorry, my unclear way of putting it. I should have said "the current thread". /g/jmriusers/message/163880 is message 163880 (no thread/topic reference).

Dave, Thanks for that explanation.? Yes, I did see a lot of indexed CVs when reading my Loksound Select Micro decoders, just didn't realize that's what I was looking at when doing it. I'm learning!

Tim, None of the Paragon 2 or 3 technical manuals mention a CV217. None of the Paragon 2 or 3 technical manuals mention indexed CVs. (If they did, one would hope that they followed NMRA S9.2.2

Ken, Sorry you're asking questions above my pay grade. I have turned off "auto connect" on my phone to the house wifi. So once I'm on the layout wifi it stays there. Bradley White Div. 12 MCR

Since the home router is still there, I'm suspect if the phone was bouncing between the two routers. If so, it would account for this loss and restore of connections. As you move around, the phone

Bradley, What are the current settings that you have now that it is working on the house wifi ?? Aaron Sent: Monday, 16 September 2019 10:33 AM To: [email protected] Subject: Re: [jmriusers] Having