开云体育

Thanks to all your replies.? I was able as someone suggested, reset the decoder to factory settings.? It still would not run with either 3 or 201 as the address.? Checking around I found a broken

Conrad, Thank you very much, and, "Wow!" I will work through this I saved your reply as a separate file for reference. The config file is the confusing part. I tried several text editors

Hello, I am using JMRI ver 4.16, with windows 7, current java version, on a Lenovo Think pad, with an MRC tethered computer interface cable #0001516, an MRC Prodigy Advance with sys v03 upgrade, com

/On 9/9/2019 12:02 PM, forfoum@... wrote:// / ???? Not going but would _give_ it to someone, who has the time, for the _cost of postage_. -- Jon Miller For me time stopped in

Hi Again Steve. All lights are setup on the Fast Clock. In doing the programming I would like to request that: 1. The Time Entry Dialog be changed to have the time "roll over" when using the

Hi Tim, I wrote an article on JMRI Operations that was published in the October 2013 issue of Model Railroad Hobbyist magazine. I believe it's still available to download for free. It's a bit out

Thanks all, lots of good ways of doing it there. I don't know how I missed that Jython has Try-Except - that will be very useful in other situations as well.?? Has it always had that capability?

/On 9/7/2019 1:34 PM, forfoum@... wrote:// / ??? OK was able to read the CVs, I think.? I'm using SPROG and DP.? However after reading CVs (motor was active then) and then using the

This is likely to be fixed in JMRI 4.17.4, due out in a day or two. Bob

Ken, Sometime in the last year a number of internal changes have happened with treatment of system names. It would seem the rule being applied to Internal system names was treating the part after the

Jim, With respect , The only thing that the LokProgrammer does is provide the user to load new firmware into the decoder. All other aspects of programming a decoder are available in DecoderPro. Since

When JMRI ver. 4.15.8 is running, loading my panel does not show any errors in the system console. I updated to 4.17.3 and my panel loads with these errors. Can I get some help please? Is there an

Hi Tim If you're an NMRA member you can view my clinic on JMRI Ops from Cleveland 2014 https://www.nmra.org/clinics/jmri-operations-just-do-it-part-1 If that doesn't work the slides are on my

Jim Several roads lead to Rome, as we say. No matter how, with Pi accessories or a computer, important is to make a backup. Of course, every write/copy should follow a verify. Half a century ago

Here's the link to the help files: http://jmri.org/help/en/package/jmri/jmrit/operations/Operations.shtml There's a reference to a tutorial in the Quick Start Help section. Dan

Peter, Daniel: On the Pi, if being run with keyboard mouse and video (or VNC remote) you can use the onboard tool to copy your SD. Accessories > SD Copier... I've used that to copy to SD and USB

Peter This is actually not an Engine Driver problem but one of you(r Pi). Obviously, you made your own RPI-JMRI installation on your Pi with using NOOBS - only then you have the OS

Don, To amplify a little bit on what Bob has just said. The nature of LCC is that there will be no conflicts created by connecting the two systems to each other to make it into one. Because it is a

If messages are to show up on both, why are you trying to keep them separate? Is there some other isolation you’d like to enforce? You could write a script to listen for frames on one interface

Nom, Your original posting does not indicate whether you want two-way communication or only need master-slave communication. Followup postings seem to indicate that you are concerned with Sensors