开云体育

Hi, How do I print the CV's page/sheet onto a single page ? I was able to do this on an old (2.12) version but can’t find how to print the whole CV’s sheet onto a single page with version 14.4

Using JMRI 4.15.7+Rf006fc4, Java 1.8.0_211, Windows 7. I'm trying to set up two arrows so I can point train direction.? I found an arrow in the resource library and I've put two on my Layout Panel

Does a firewall exist when working with a RPi? Where exactly would you look for the presence of a firewall? there is no windows pc involved here. Bob Thanks. Regards, Bob Phone / Fax - 440-838-0508

Do you have an i phone where engine driver does work correctly? or prhaps a samsung android unit?? I run a raspberry pi and am seriously considering using my tablet for a wifi throttle and leaving a

Peter, the most common issue for those symptoms is a firewall blocking the incoming message. Make sure ALL firewalls are turned off, test, and if it works, then you can add an exception for WiThrottle

Hello, When using the manifest view, operation tab on 4.15.7, each car has a 'null' in the data line. Example: Pull SP 481289 null MTY from U&I Coal I believe - not having any other version than

Thanks for your valued input SwissChris. I See your Accessory problem if your current setup allows any loco to cross any turnout set against it. It is akin to a ’S.P.A.D.’. I overcome this by

Regarding IR sensors, the sensor comes with short 5mm leds. I suggest you desolder these and install 3mm leds on long leads. They will then fit nicely between the members and extend down thru the deck

Being guided by Steve Todd I set up JMRI image file on Raspberry PI3 and could connect to my Digitrax dcc train layout. I could setup turnouts, routes and locomotives. I could see everything on Engine

I'm currently running 3 DCC systems on my layout. Don't ask me why, but it's to do with different systems not able to do what i want. Loco, Accessory and Block control.. My loco control is by

In your JMRI preferences have you set it to 'SPROG'? or 'SPROG COMMAND STATION'? if it is on SPROG COMMAND STATION? set it to SPROG, this may be your problem.

To all I am having issues with a Sprog 2 V3 and trying to use WIthrottle The sprog is functioning correctly using jmri throttle and controls 2 locos with different addresses I use the sprog mainly for

Thanks for that Jim, I am slowly wrapping my head around what I need to do next and with what hardware. I must say that I would prefer to stay with Apple’s OS now that I have left Windows behind

Dave: Some possible misunderstandings... JMRI is Java based so it's not machine dependent... I have it running on macOS, Windows and a couple flavors of Linux. Just as long as the OS is happy with the

OH NO! I had enough trouble getting up and running with the panel server. How does the frame server work? I think I'll just take the advice of others and just go buy a newer tablet. There are some

Thanks for that Randall. I will have a play when I get home. As regards the ‘Hardware’ I do all my development work on my iMac which can run "Windows" using the program “Parallels”. I also

My android tablet has this issue as stated above. The device is a D101. Could this be part of the problem? Bob Thanks. Regards, Bob Phone / Fax - 440-838-0508

The number of connections a JMRI application supports is theoretically limited only by your hardware. To add another connection to a single JMRI configuration profile: 1. Open the Preferences window,

I am reaching out to anyone who is using JMRI with multiple systems for help, please. I have just swapped to using the new Lenz system having used the ZTC system for Train Control only for several

Hello Michael, is there any possibility that some corrections/edits/additions that I provided for TCS non-wow decoders and last checked in 2018 can also be included? They were still functional as at