开云体育

Glad you were able to get it to work. Thanks for the information, it should be helpful. Of course I don’t think there are too many of the non-production LIUSBs are out there.

Test version 4.15.2 of JMRI/DecoderPro is available for download. This is the next in a series of test releases that will culminate in a production release, hopefully in early Summer 2019. If you

You wrote: Reinstalling older versions will not fix your problem. The problem was caused by an issue in V4.12, but reinstalling v4.10 will never fix it. It will now be there in V4.10!!! You must

Absolutely definitely you have some Preferences->Defaults set to Internal (Bob has explained how to fix that...) or you have NCE System Connection set to "Simulator" in

Dave I memo'd a Massoth problem a few minutes ago 1/13/18. What IF I re-install 4.10 then 4.14 around 4.11/ 4.12/ 4.13? OR run 4.10 until the issue is resolved/

Have you set the “Startup” part of the Preferences to load your file? Bob

Open the preferences, then pick “Defaults” in the left to get to the default pane. Make sure that the radio buttons are selected in the NCE line all the way across, not the Internal line. Save

JMRI 4.14 Decoder Pro; worked a few months ago on 4.11/10. Not on 4.12 NCE? version newer than 2006 and it worked also w/ 4.10. Computer Dell Dimension 2400 XP?? PTB100 on program track Decoder PRO

Digitrax Empire Builder / DB150 / PR3 / Lenovo Laptop W/Win10,64bit / JMRI 4.14 / Raspberry Pi 3B / Steve Todds' image for the Pi / TightVNC Viewer. I am unable to save the lists of Turnouts and/or

Hi all Just installed the latest version of JMRI 4.14 on my new HP laptop computer Windows 10. Latest version of Java etc.I'm using a PR3-Extra and DCS51 for my Loco-net interface. USB 2.0 I

Hi Bruno; Can you run ls -l /dev/tty[a-z]*? after connecting and powering on the Lenz side I think we'll need to create another profile. - David M

So the Defaults had changed prior to the update? and just continued on till corrected.?? As Peter says, running 14.4 is good as it contains fixes to stop these infamous Connection and Defaults

Defaults changing were issues in the previous 2 JMRI production releases. Make sure you are using at least JMRI 4.14. -- Peter Ulvestad JMRI Users Group Moderator - http://www.jmri.org (

Marc i have changed them all to Z21 and you are correct, it works again - clearly something has changed either within JMRI or with the lat st Z21 firmware (1.33) as I haven't changed these settings

hi Steve, No worries. I have some Lenz equipment and can help with testing. It seems some of these older Lenz 23150 USB Connectors where kind of sample devices which aren't that easily recognizable

Possible CV29? is set with DC (analog conversion)? enable. This will cause engines to race off thinking they see DC on track if no DCC signal is present. CV29, bit 2 Marc

The easier solution is to change the normal direction of travel in CV29. That will make forward direction right. In the comprehensive programmer, this setting is on the basic tab. You may need to

If I setup defaults as you have them (all Z21Loconet),? I also end up with greyed out on New LOCO and no read. If I set DEFAULTS to all? Z21, then the New Loco is not greyed out and read/write

Hi Steve, I thought as much, the turnout mode is set to Direct, with Feedback 1 and 2 blanked out and Turnout automation set to off, i have taken a screenshot

Strange happening. I upgraded from JMRI 4.11.6 to 4.14 and suddenly I could program the troublesome unit completely. I thought this was strange but, I'll take it. As I had been using a home-made