开云体育

Sorry Bruce, I forgot, the new SOUND decoders cannot do that.? But YES, YES, YES, that DOES work on non-sound decoders. Have you ever tried it ? You can even do it with Digitrax. I have, and YES it

NO! NO! NO! It doesn’t work that way. -- Bruce Petrarca bfpetrarca@...

Hi Robert, Not at all sure how it could have caused the ensuing mess, but there definitely is a hole in your way of working. Where you said 'wrote page' (after my first whoah...) you were writing

Hi there, I'm quite new to DCC but I'm very familiar with Arduino. I've developed two Arduino shields recently. One offers 5 channels of block detection per Arduino, and the other does 4-aspect

1 + 2 We use NCE on the mainline, but the programming track is SPROG III to computer, USB interface 3 no 4 no I have not, will look into it Rick Knight? What do you think? 5 did not know that will do

We are using a sprog III with it’s power supply, I do not think it was in adequate power Robert J. Richter 283 Elm Street North Reading, MA 01864 Sent: Wednesday, January 9, 2019 12:25 PM To:

No booster, sprog, short track Robert J. Richter 283 Elm Street North Reading, MA 01864 Sent: Wednesday, January 9, 2019 12:10 PM To: [email protected] Subject: Re: [jmriusers] Broadway ltd There is

That is what has me mystified also, thanks Ken Robert J. Richter 283 Elm Street North Reading, MA 01864

See below Robert J. Richter 283 Elm Street North Reading, MA 01864 Sent: Wednesday, January 9, 2019 11:52 AM To: [email protected] Subject: Re: [jmriusers] Broadway ltd Hi Robert, I am totally

I work with a Digitrax 240 system at my club and I have a Sprog at home. I never have problems reading/writing a BLI with the Sprog but always have issues with the Digitrax even with a PTB-100 added

Not an ECoS expert at all, but happy to work with you on tracking this down. Can you build & run JMRI from a GitHub branch? If so, I can push a version with a bunch more diagnostics in this area for

Hello Alan, reading CVs by directly using the keypad on the Twin-Center works as expected. I can hear the relay switching the program track on when I enter programming mode and all basic CVs read and

(Separate reply in case it becomes a separate thread) I think the goal is to create “how JMRI works with MQTT” without a lot of attention to the (very small) number of existing setups. Any

I only have one BLI loco, Mikado, I have not had any problems what so ever reading or programming this loco. My secret to programming locos, any brand (I haven't tried MTH though) is to use JMRI and a

Robert, Just a few questions on your process.1. What type of DCC system ?2. How is it connected to the computer system. (Locobuffer USB for Digitrax or PR ? from Digitrax) or a PB100 from NCE.3. If it

Two examples: If the system letter is M, then: *) MTfoo/bar/biff/21/mine is a turnout that uses foo/bar/biff/21/mine as the MQTT topic *) MSrailroad/stuff/notMentioningSensorsHere/yardOSwest is a

From: Classic Auto Portraits <mailto:classicautoportraits@...?subject=Re:%20Broadway%20ltd> Date: Wed, 09 Jan 2019 09:32:45 PST Dear Mark, et. all, I have a Digitrax DCS240 command station, with

On Wed, Jan 9, 2019 at 10:19 AM, Kevin wrote: > > Hi David > ? > I’m a UK modeller too, and a JMRI user. I’m struggling to work out why you > are looking at DCC++ on an arduino when you already

From: Classic Auto Portraits <mailto:classicautoportraits@...?subject=Re:%20Broadway%20ltd> Date: Wed, 09 Jan 2019 09:32:45 PST Dear Mark, et. all, I have a Digitrax DCS240 command station, with

Hi David I’m a UK modeller too, and a JMRI user. I’m struggling to work out why you are looking at DCC++ on an arduino when you already have a Dijikeijs DR5000. The DR5000 will act as the DCC