开云体育

No I don’t have a command station. I was hoping to use my windows 10 computer with jmri software an interface and a test track to just read and change the cv settings. I don’t need to run the

Luke(?), My notes say that the PR4 red and green lights flash rapidly when the PR4 is in "IPL" mode. I do not know where I got that information. If your PR4 continues to exhibit this symptom, I

Neafus, I install decoders in N, HO, O and use the Sprog 3 it programs anything that is programmable. Gerry -- Gerry Hopkins MMR #177 FNMRA Great Northern Downunder

I just tried to load my RailDriver throttle in JMRI 4.18 and it did not load plus the console shows an error (copy below). I am using Ubuntu 18.04. I rechecked 4.16 and it still works there. Did

John, As Peter has already said, JMRI can program CVs in ESU decoders. I've developed all the special JMRI code and definitions for ESU V4 and 5 decoders. My test systems are: - NCE Power Pro with

Clay, That is helpful.? So, the error is coming from CATS and not designer?? That would make sense, as I don't remember that designer had that kind of error checking on sensor and turnout names.?

On Sun, Feb 16, 2020 at 02:58 PM, John wrote: > > If you will NOT be using ESU decoders, then I would suggest a SPROG. I use one > for non-ESU decoders. ESU decoders need the LokProgrammer for

If you will NOT be using ESU decoders, then I would suggest a SPROG. I use one for non-ESU decoders. ESU decoders need the LokProgrammer for installing the sound files. I have both, I swear by my

On Sun, Feb 16, 2020 at 12:00 PM, <ktellis68@...> wrote: > > I believe I am experiencing the same problem as well.? I have PowerCab > version 1.65 and just recently purchased the NCE USB

JMRI supports a lot of different hardware https://www.jmri.org/help/en/html/hardware/index.shtml Most of the common systems will program most decoders. Do you have a DCC command station at present

ktellis68, Power Cab Instructions ================= The best beginner-level settings for a Power Cab (any version) and an NCE USB (any version) are: - All USB Jumpers off (or at least 2, 3 & 4. Jumper

I hope I’m not posting to a worn out topic but I need some information. ?I am wanting to set a decoder programming track to program decoders from different manufacturers. With the jmri software

That’s a great idea! I had done this before JMRI, don’t know why I forgot it this time! Thanks for this solution! Terry Cummins S.E. Michigan Sent from Mail for Windows 10 Sent: Sunday, February

Ken, this is a great service you guys provide! To this end I have some other issues with my panel that I need to ferret out before I would do this . But if I can’t I would like to do this in the

See, this is what makes this site so great! Method 1) Rather than using the association of the two turn out I could have just identified them on the panel with the same number. Method 2) make a hard

Some advice I was given was jumpers 3&4 on baud rate 19200. Start NCE Powercab, start computer, plug in usb and then start panel pro. It did work for me.

I believe I am experiencing the same problem as well.? I have PowerCab version 1.65 and just recently purchased the NCE USB Interface.? I am using Windows 10 and have the latest version of Java

In all likelihood, Terry is wiring his layout as indicated in -splasher's response: However, since he is asking us, the question posed by Peter is important. If the original posting is asking about a

Rodney, I've been helping Mark with CATS. I started a panel in Designer to show him how things work and when we tried to bring it up in CATS we got the error message he referenced in his post. When I

Terry, A lot of this depends on the hardware being used, if feedback is being used, and how you set it up in the panel. We'd need a number of details and seeing the panel file would be the best way.