开云体育

This is the 18v P/S I got for my PR3.? With it I could program everything but a BLI Paragon 2 N-Scale PRR M1a/b.? I had to go to a SPROG 3 for that.? I could program ESU, Digitras, Lenz, NCE, TCS

I just finished installing a TSU-PNP GE, and have run across a strange problem.? When I try to add a new loco in DecoderPro, it fails to correctly identify the decoder.? If I manually select the

I think a good way to explain this is to insure the current that flows out to the contacts on the Tortoise flows back to the same spot and takes the same route. This is the best way to insure things

Bob, Thank you for the help. Please let me know when to download the new JMRI. Ken

I'll chip in with my PowerPax history. I came before the PTB-100 was available, maybe before the PR3 too. But it came with an 18V supply. I've been using it successfully for at least 6 years now,

Hi there, I have had similar problems with my PR4. Can anyone suggest the best product to use as the power supply and the PS14 jack on the PR4? Or alternatively an adaptor between standard chargers

Thomas, If you have an NCE Power Pro system, you can set Turnout Feedback Mode to MONITORING and your JMRI panel will be updated by NCE throttle or Mini Panel commands. Unfortunately the NCE Power Pro

Thomas, My experience with the NCE Power Pro, PowerPax and PTB-100 was similar. The PowerPax did not work as well as the PTB-100 with my Power Pro. Dave in Australia

Dave, The three wires connected to pins 5, 6 & 7 need to go directly to the AIU GND terminal and two input pins of the AIU. They should be routed close together and preferably lightly twisted

Hi P?r, I have uploaded a script example that will hopefully be helpful. /g/jmriusers/files/VSD/SensorListener.py You have to open the LocoNet Monitor to see the transponding

Frank: The suggested solution to the Android change is to operate in Airplane mode. This turns the phone system radio off so we're not trying to connect to the net over that network. Jim Albanowski

Roger, Downloading a new image from Steve seems a drastic way to upgrade JMRI when all you need to do is download a linux version of JMRI and extract it. If you checked all the links Steve provide, he

Hi, I am using JMRI for a shelf layout I have. I run my trains using scrips and I am using decoders, sensors etc from a Swedish company? mollehem.se My layout is N-scale and I would like to use VSD

Bradley: Turning off auto connect removes one potential problem but the other is that your phone may be looking for an internet connection - and there isn't one on your layout router I presume. There

My apologies to the group, because I think this was answered to someone else a very short time ago, but I can not find the email and accompanying information. I have a JMRI Panel set up to control the

Sorry, asked a relatively simple question in a complex way... Main computer tied to Loconet (either with a LB-USB or directly to a DCS240) and WiFi clients (RPi's) running JMRI instances.? Either of

Frank, My DCC command station is the NCE PH Pro 5 amp system. I purchased a Power Pax to program the newer sound decoders and it seemed to do the job for a while, but eventually I put it away and

Hi Jim ...YES...YOU GOT IT....That is Exactly what I am experiencing. ?YES, I think there was an update on the android software. ?I (hopefully) will check with the author of that software. ?THANK

FYI, I also never received and email from the group, with a person name Dick on it Thank Dave In PA Sent from iPhone Xs Max

Hi Dave Sorry for the delay, been sick. I am confused on your last reply, see below about a ground loop. My Assy. Bus is power by a separate external power supply, unrelated to my DCC power system. My