开云体育

Bob, As you guessed, R/W is required at this time. That means the EB is not supported. Robin Becker Tucson, AZ http://home.earthlink.net/~n3ix/drgw.html

I didn't mention that I have an Empire Builder II. After reading Robin Beckers reply to the last message, I wonder if I'm screwed at this point? This simple project is getting out of hand. (G) I

Mike, The EB (DB150) does not provide readback of CVs and does not support a separate programming track. I think that currently DecoderPro supports Digitrax via the programming track of the Chief

Bob, Digitrax is soon releasing the lower cost DCS050 and this unit has a programming track. I am going to get one when they come out, probably June or July. Depending on their specs. (it's not

Group, I think Bob did some experiments with a DB150 (EB) and found that he could write but as we know the EB has no programming track so no read back capability. This is a type of system problem

I have a DB150 hooked up to my computer via a LocoBuffer. Before I found out that the DB150 can't read CVs I thought it wasn't working, however I am able to write CVs. Sure is much easier than

Group, Another plus for our beloved DecoderPro. I bought a group of CVP AD4 accessory decoders for switch motors. Not wanting to do these by throttle I first used PR1DOS connected through the

I've added a "Roster" menu to DecoderPro that let's you copy, delete, export and import locomotive configurations. The first draft of a web page describing this is at

Sorry for the slow reply. The Empire Builder doesn't have the ability to read from decoders. There's nothing a PC can do about that, unfortunately. DecoderPro should still be able to program them,

Sorry for the slow reply. Perhaps you've got it working, at least for write operations now? If not, there are a couple things you can check to help track down the trouble. First, see if basic

Bob, When using an EB (I have a DCS100 not a BD150) you would have the problem of not knowing the initial decoder settings, so does DecoderPro set all the CV's to a particular value (0 ?) when you

Each CV has a default value specified for it by the writer of the decoder specification. Some default to zero while other CVs have defaults configured to be the same as the defaults the factory

That's a good idea. I played with it some last week, but wasn't able to make it really reliable. I'll keep working on it. (The problem is that the index can be in two places: The xml/ directory,

Bob, Thanks for all your work. I'm sure you'll come up with something for the index files. I tried out the roster tools this morning and they looked good. Jim will try to keep an eye out for a

Did a DecoderPro install today for a friend, and he immediately ran into confusion on Digitrax and Lenz decoder models. He had a factory installed Digitrax DN146 decoder and a factory installed Lenz

The DN-146A program wise is the same as a DN-140. The DN-142 has transponding and back emf that the 146 and 140 do not have. Program wise the DN-144K, 145K,146A,147A & 148K are like a DN-140. While

Michael, Thanks. I don't see a DN140 in the DecoderPro set at this point. For reference, can you point me to where on the Digitrax site this is all spelled out? Robin

Robin, In my version I have a DN140 and a couple of DN142's. Looks like a little housecleaning is in order<G>. Jon Miller AT&SF For me time has stopped in 1941 Digitrax DCC owner, Chief

This just was posted on the Digitrax list, useful information! Out of production Digitrax decoders are listed at http://www.litchfieldstation.com/E/DccD/LD/OutOfProductionDecoders.PDF Jon

Bob, Jim Hanna found that IDENT didn't work for NCE decoder. Checking into this, I found that the NCE name is used differently in the decoderIndex and the decoder files. In decoderIndex.xml, it is