开云体育

Hi Bruno; Can you run ls -l /dev/tty[a-z]*? after connecting and powering on the Lenz side I think we'll need to create another profile. - David M

So the Defaults had changed prior to the update? and just continued on till corrected.?? As Peter says, running 14.4 is good as it contains fixes to stop these infamous Connection and Defaults

Defaults changing were issues in the previous 2 JMRI production releases. Make sure you are using at least JMRI 4.14. -- Peter Ulvestad JMRI Users Group Moderator - http://www.jmri.org (

Marc i have changed them all to Z21 and you are correct, it works again - clearly something has changed either within JMRI or with the lat st Z21 firmware (1.33) as I haven't changed these settings

hi Steve, No worries. I have some Lenz equipment and can help with testing. It seems some of these older Lenz 23150 USB Connectors where kind of sample devices which aren't that easily recognizable

Possible CV29? is set with DC (analog conversion)? enable. This will cause engines to race off thinking they see DC on track if no DCC signal is present. CV29, bit 2 Marc

The easier solution is to change the normal direction of travel in CV29. That will make forward direction right. In the comprehensive programmer, this setting is on the basic tab. You may need to

If I setup defaults as you have them (all Z21Loconet),? I also end up with greyed out on New LOCO and no read. If I set DEFAULTS to all? Z21, then the New Loco is not greyed out and read/write

Hi Steve, I thought as much, the turnout mode is set to Direct, with Feedback 1 and 2 blanked out and Turnout automation set to off, i have taken a screenshot

Strange happening. I upgraded from JMRI 4.11.6 to 4.14 and suddenly I could program the troublesome unit completely. I thought this was strange but, I'll take it. As I had been using a home-made

Hi all, I have a combination of latest stable JMRI on Lubuntu (or Mac) with Sprog Nano with the following: During start up * Load WiThrottle server * Load Webserver * Load my railroad config *

Hi Tim, Am thinking that this isn't CBUS related Another quick thing to test, does it work when sending event 503 from the event table? What feedback mode do you have set for the

I don't remember the details - I worked on this 4 years ago with @kjlisby - but there are differences in the LN implementation between IB2/IB-COM and IB 'one' (or Fleischmann TC); and a number of IB

Hi Steve,? Yes its a little unclear i will admit. basically the panel never updates the turnout position, IE the icon doesn't move? when the event "503" is sent from the CANCAB.? The turnouts

Hi Tim, Yes, the same Steve Young! Thanks for the GIF however I found it a tad awkward to understand! The one thing I spotted was that there was an incoming short event containing a node number,

Hi Bruno, since the autoidentify is not working, you should disable it (there's a desktop icon for that). Then open PanelPro and select a similar profile, or just create a new one. Then set the

Hi again; Regarding RailDriver support, it would be nice to have it as a Jynstrument, like I did for Wiimote, various USB pads, and even a DCC throttle, see code in

Hi; regarding video playback in a JMRI throttle frame, I had build something a while ago, I think the code is still there ( jython/Jynstruments/ThrottleFrame/VideoView.jyn ), see this video (

Hi Steve, Thanks for the link, i did try that but to no avail, enabled or not it seems to make no difference. I can click on the panel editor and it does change the turnout, but the panel doesn't

Thanks Dan and Peter. Dan, I thought CSV was most likely the easier and more efficient way since the columns would be easier to manage. I never thought of first exporting a "dummy file" with no data