开云体育

John When using the Tsunami 2 or Econami - remove the PTB100. Gerry

Hello Billybob & John, I sent a reply at noon today, but don't see it, so I'm sending a new update via 'add to the conversation'. Sorry, I'm new at this Yahoo Group thing. I installed version 4.11.3

Randall: Which LocoBuffer? I have the older LB-USB and the FTDI drivers install for a serial device. Needed to do Google RR=Cirkits USB drivers... drivers for 10.4 (Intel) and higher. Reports

Jay, As Steve Todd has stated earlier, use a leading zero in your turnout numbers below #10 if you have less than 100. E.g., IT01, IT02..., IT09 Ken Ninomiya Oxnard, CA >>>>>>>>

You need to explain this box in more detail and tell us exactly what it says. It is quite likely indicating a problem that is preventing you from setting the defaults correctly. The exact wording is

Ken, I was not able to keep the change from "internal" to "Loconet".? I went into Preferences and made the change from Internalto Loconet.? But when?JMRI had to shut down to save the changes, they

Hi again folks Well, progress is being made at this end. I downloaded the latest test version 4.11.3+R80b3ab3 as suggested and then opened a withrottle on an iphone 4 running withrottle 2.2. I was

Hi Mike Thanks for the response. I've tried: s.dispose s.shutdown(socket.SHUT_RDWR) No luck so far. A lot of sites mention using: s.setsockopt(socket.SOL_SOCKET, socket.SO_REUSEADDR, 1) However I

Also consider using sensible user names for the turnouts. To simplify the display, use a separator (default is : ) and then you get them grouped by the prefix part. Great for larger layouts so you get

Hi John & Billybob, This morning I installed Version 4.11.3 over version 4.10 and experimented somewhat using the 'Slot Monitor' tool. This is what I found: 1. In effect, I found a 'work-around' as

The easiest fix for my sorting issue may be to give the turnouts locations based off the turnout numbers. For example 1 through 9 be in a location called Turnouts 1 -9. 10 through 19 location called

Ken, I'll try this?and will let you know. Thanks for the advice. JP To: jmriusers@... Sent: Thursday, March 8, 2018 9:07 AM Subject: RE: [jmriusers] Fw: Subject: Issues with latest

John, A quick thing, check the settings in the Preferences->Defaults. Sometimes they get changed to 'Internal' instead of your real system (LocoNet). If the radio buttons are on Internal, change them

Hi, Mine are named IT1, IT2, IT3,..... I have the same issue as Kenny! Jay

Hi Kenny, 1. The turnout initial states should match those shown in the JMRI Turnouts Table. Do yours? This behavior is hardware-dependent. Some systems, such as my LocoNet Tam Valley servo

I have 2 questions concerning using turnouts in the Engine Driver app. 1. When first starting the app all the turnouts on the turnouts page show a status of ???? Until the toggle button is hit once.

Hi Paul. Be consistent in all things.... Ensure all you anchor points are complete, that is green on my panels. Ensure when adding blocks to sections that the "REVERSE" "FORWARD" entry point

Hi Jim, Thank you the feedback. When I wrote the decoder definition of the Economy Series 6 series, I indeed relied on the product description to remove BEMF support from the definition compared to

In helping Frank get his system up, we are at the point where his iMac is confirmed to not be seeing the LocoBuffer-USB as a Virtual COM Port (VCP). We’ve gone through the installation of the

Thanks Dave/Ken for looking into it. Sounds like good news.? I will report back of course when I have received and fitted the update to the SB3a.? My sensors are already created, with NS prefixes