开云体育

Hello Ken, No it is not a serial ethernet, but an arduino ethernet shield that comes plugger on the Mega Arduino. It uses the classic ethernet protocol. Thank you :-)

Thinking Dave down under, had to many Kangaroo Juices. Just teasing. Thank for all the help you provide to this forum Dave Mount Joy, PA Sent from my iPhone 6 Plus

Fcot, Are you using some serial to ethernet adapter? If that is the case I suspect your setup for things like how it knows when to send packets is not correct. I've seen a lot of those devices that

Hello boy's Bad news ! Yesterday I mounted a brand new DCC ++ Ethernet for a friend, and the problem of slowness is reproduced. We switched to a USB serial and everything is ok. Thank you Jim

PS Apologies all for getting the release numbers wrong, should read 4.15.7 and 4.14.4, oops! Steve

Hi Tim, Fix contained in upcoming JMRI release 15.7 The Light Controls showing this message in JMRI 14.4 OpenLCB will still operate, it's just that the very first Light ON command may not trigger

Jerry, One of the main reasons that most use current detection is then anything, even a single wagon with resistor wheels, in the block will show up and that is what I would use but I was just trying

You want to do two things: - In your profile, using PanelPro, under "Preferences->Start Up", you want to add an Open File (pointing to your Turntable.xml file) and Run Script action (referring to your

All, I apologise. That statement was in error. Behaviours for editing a filename are not consistent across platforms (nor is the "Open" behaviour). Too late at night... Dave in Australia

All, This behaviour has been around ever since the main DecoderPro3 window replaced the old clumsy and extremely dated dropdown list interface that was unworkable if you had more than 5 or 10 locos in

Rance, You need to find the JMRI system console. It will tell us if JMRI is encountering an error opening the roster entry. When you start DecoderPro and the main roster window appears (all the loco

Hi Steve, Some great ideas there - particularly about using MERGCBUSServer. I'd forgotten about that. I used it for a while after we had it demonstrated at one of the MERG meets. At the time I saw it

If you are looking for a printable pdf, on the Jmri website> manuals tab at the top>far left edge is a pdf for 3.4 After that its all online as best as I know. Tom Wilson Colorado Springs, CO

Hi, I’ve just updated to version 4.14 and looking for a “User’s Guide” for version 4.14 I had an old User’s Guide for version 2.12 and found it very useful but I cannot find a similar Guide

Greetings, I think I've got my configuration working to control the Walther 130' DCC-controlled turntable from our LCC control panel. As a reminder, I've got a Raspberry Pi mounted under the module,

Marc, I'm not talking about the roster window as displayed on the DP3 main panel ( http://jmri.org/help/en/manual/DecoderPro3/images/start_dp_main01.png ).? Yes, I'm sure it'll behave the same

Mike, There has been some discussion of the problem of "proper" system-specific interpretation of current meter information as of 27May2019 on the "jmri developers" e-mail list. This is getting some

With JMRI 4.15.6, DCC++ (Arduino Uno and Pololu motor shield) hosted on PC running Linux the values reported by the track current meter (DCC++ => track current meter) are off by a factor of 100. For

Charlie, Letting the PC go to sleep will disrupt the device driver. It will not recover. That's why you have to close JMRI and reopen it. -Ken Cameron, Member JMRI Dev Team www.jmri.org

I've always felt that the "DecoderPro 3" interface was beneficial only to the person(s) who wrote/promoted it. ISTR there was a lot of discussion about it, so much so that when it was made the