开云体育

Don’t you key the amplifier from the ‘send’ RCA connector on the back of the radio? When the radio is in transmit, you should hear your FT8 signal from the radio. I don’t think the ‘send’

Bob, I use the LDG AT-7000. It's very good and draws it's power from the connecting cable between it and the radio. Milton, N6MG

It is an excellent auto tuner. It will match a wet string. I have had 2 of them and still own one now. Nice features include internal battery holders for AA batteries so it can be independently

73's for the info. We'll continue to look at the LDG products. Not ready to buy yet.

The KPA500 is matched up with KAT500. The LDG at7000 is for portable work without the amp. -- Allison

Can't help as mine is paired with LDG At7000, plugs and plays. That version was intended to play with the IC7000. For my KAT500, I use manual mode and press tune with a 20-30W carrier (am mode) and

Hello, just signed up for this group. I note some discussions about antenna tuners. We have not really tried one yet, but it was suggested to us to try the LDG Z-11 PRO II. Any suggestions? Bob

Are we trying to sell SignalLinks?? I already have a interface box, its compatible with Tentec Eagle, Tentec 6n2, FT817.? I just have to make up a cable for the box to the IC7000 and would likely

I also use the SignalLink with my 7000. I first used it for PSK then, later, found it worked really well for FT8. I bring the power down to 40W or so and it works very well. I never bothered with data

I figure using the small din for the PTT (it also cuts off the mic in data mode). The 13pin ACC as I need RX and TX audio for my interface.? I have that plug. I may keep a 12V fan handy, but the

It has been a while, but I think that the 6 pin mini-Din jack will work and not require removing the mike to prevent audio from there being transmitted along with the FT-8 signal. As I remember it I

13pin ACC has all the connection. Use HSend (hf) for ptt, mod for audio in and AF for audio out. 3.5mm mono (or stereo with tip and body) for cat/c-iv. A small dc fan at the back blowing air on heat

Paying for hardware is a choice, just like building it. Being retried I have the time, I do prefer to not spend when I don't have to.? ?The connector was the bottleneck not the computer interface.

What are good settings for Signalink USB for FT8 and IC7000? (assuming WFJTX) VY 73 de W3UECSteve Dubinhttps://substack.com/@eldervet?In a message dated 5/6/2025 3:18:11 PM Eastern Daylight Time,

Allison, I actually paid a bit for the cable (from West Mountain) that connected the 7K to the RigBlaster…. Time is valuable – always fun to roll your own, but…. 73’s Glenn WA6BJQ From:

I suspected a PS2 cable I have a few of them from dead keyboards. I use a HB interface with PTT from the computer so simple is what I do on three other (non-icom) radios. -- Allison

I use the SignaLink USB for digital modes. 73, Adam, ve3fp [email protected]> wrote:

I use the 6 pin mini-din plug (Data port) for FT-8 and other audio card modes. I use an USB to CIV plug adapter cable for rig control. The 6 pin mini-din is a standard PS2 keyboard cable. The

What connector is used for FT8 ACC or DATA? THen where do I get that DATA minidin plug if that's used. -- Allison

I have never had a problem with viewing the video output on a small or a large TV screen. I have used various 7" monitors and TVs and also the video monitor in my Town and Country Mini-van. Perhaps