开云体育

Bad speaker jack. ________________________________ Sent: Thursday, August 24, 2023 07:25 To: [email protected] <[email protected]> Subject: [ic7000] Audio issue with internal speaker Hi all, My

The speaker jacks on the IC-7000 are small and old and may not be making the switch contacts etc. A little cleaner might help with this. Otherwise is wiggling the plug helps and perhaps cleaning

Hi all, My IC7000 seems to be suffering a somewhat intermittent issue with the internal speaker. When I powered it up yesterday the internal speaker wasn't working, after using an external speaker

I recently had a very satisfactory repair done on my IC-7200. No connection other than a satisfied customer. Matt Adrian SAR Technical Services, Inc. ICOM Authorized Service Center – MI 1792 Nash

Hello all, I've owned my IC-7000 for around 13 years now and I guess a couple of years ago the radio fell off the table on it's face and the impact bent the stock of the PBT / M-ch knob. It ended up

I simply tuned for maximum receiver noise which got me close enough. Used a KJ7U Shorty II. https://www.ka6wke.net/hf-mobile/2004-dodge-2500-diesel Tried the Hi-Q too but found them noisier than an

I had the HS 1800 HP and used just a double pole switch, up / down. My 7K has the multi function meter, swr, alc, po so when I tune drop the RF out to 10%, use RTTY for carrier. Adjust the antenna and

All, I was just able to find a used Tunematic TM1 units with the Icom interface on facebook of all places and snapped it up. (I had ordered the West mountain Target tuner for my obsolete Hi-Sierra

I second the Tunematic. Mine is the Lite version, very simple to use with good repeatability. The antenna is a ground mounted Tarheel 100HP. HOA stealth. 73, Jack W9JH

http://tunematic.jtcomms.com/wp/ This is more accurate and doesn’t need to reset the antenna often as the better RF did for me. 73- W1JCW John Join my new SteppIR Antennas IO group by sending an

I think I have the black box still, Fokko. Mail me I'd say.

Did you have any luck finding a screwdriver control yet?

Dudley, The referenced relay in the IC-7000 only selects between two different SEND control lines, that allow separate control of HF and VHF/UHF amplifiers, depending on a menu configuration.? The

John, I have not look specifically at the 7000 keying circuitry, but some of these newer styled radios do not use a physical relay, being an open collector path to ground, there for need a slight dc

Thanks Steve,? I have checked the diagram in the service manual and see the circuits involved.? The 13.8 VDC is good.? The problem is Hsend or Vsend does not go to ground as expected when going to

There are no negative voltages on the board, so perhaps your (-) meter lead is on the wrong trace which is not connected to the DC- ground.? Look at the ACC circuit schematic on the DDS board in the

Yes i know about the jack in the back. i have conncted a dummy load still nothing replaced the final that is a comman problem still cannot adjust. Think my pre driver might be the problem

I managed to kill Hsend and Vsend on My IC-7000 maybe by shorting the 13.8 V on pin 8 to pin 3 on the 13 pin accessory plug.? Pin 3 and pin 8 show around -4 volts on both receive and transmit.? Has

Hello Members, I am looking for a BetterRF 7000 screwdriver control (yes, I own already the BetterRF Tune Control). 6 years ago I swapped my IC-7000 for a FT-991A and also added the above mentioned

Hello Members, This is PA3VOS. I have been operating on HF from my mobile for more than 20 years.? 6 years ago I sold my IC-7000 as well as my HiQ 5-80 and the BetterRF Tune control with the 7000