开云体育

Unfortunately, while CHIRP is my preferred radio programming normally, it has a significant limitation for the IC-7000 in that it will only read and write Bank A memories (shouldn't be too hard for a

There's a heap of software that works with the IC-7000, you would get a lot of results out of a Google search. Most popular rig control software (Ham Radio Deluxe, etc) supports the IC-700, same for

This should work http://chirp.danplanet.com/projects/chirp/wiki/Home Brian Mackey KC1MAC Hams don't let hams get stuck on 2 meter repeaters! From: <rickmandziak@...> Reply-To:

I had a MFJ-998 but sold it when I purchased the Icom 2kl, the IC-at 500 automatic tuner, and of course the power supply...I also have two manual 3 kw MFJ-986 and MFJ-989 tuner To:

Do you have an antenna tuner? They are not terribly expensive, especially on ebay, and are worth every penny. My antenna for 60 is a 125 foot center fed flattop fed with balanced line from a MFJ-993B,

Mine is a second owner rig.....I traded a TS-2000 for it.......Must be a 2011 as the serial number is below the 2012 number.....This one has been opened up for frequencies also......60 meters is

When was yours made? Mine, purchased in August 2013, is OK for this bunch of channels, but it takes some work to get them. In my Yaesu 950, they are pre-programmed in as memory channels. KC4BO Alex

My serial number is 0513348 I will need the mod...... de w1nv Don To: ic7000@... From: anetherton@... Date: Thu, 19 Dec 2013 21:03:11 -0500 Subject: Re: [IC-7000] RE: IC-7000 on 60

I would really like to figure out how to get on these frequencies on my 7000. KC4BO Alex Netherton http://blueridgediscovery.org

Older IC-7000 were limited to 5 channels for 60m. and USB only. This no longer applies to the newer models. I have a newer IC-7000 (abt 6 months old). It transmits on a range of frequencies in the 60

Thank you all for the great information.73.Bill / N1ASS.

All I did with my 7k was to program in the 60 meters frequency 1.5 below the center frequency per the manual into memory......SN #051XXXX de w1nv Don To: ic7000@... From:

The answer is yes. You will need to know the serial number of the IC-7000 you buy. Somewhere in the archives of this group is information on which serial numbers are "old" 60 meter

Icom released the changes around 03/2012, effective with SN 0514455. I would hope any new stock would have the change by now. If not, the mod was released by Icom and takes about 10 minutes to do.

I am thinking of buying another one and the question I have is that do the new ic -7000's do the have the new ch 3 (5.357.00) replaced from the (5.366.500) on 60 meters???????? Thank you.Bill /

Those interconnection straps are spot-welded to the cells, so not sure how much good it would do. If you tried soldering, the heat may damage the cell. Nickel can be soldered, but it's much harder

I have repaired battery packs several times by soldering and causing no damage. In one case, the spot weld was bad and the strap was detached from a cell. Scrape both the cell end and the strap with a

Can anyone help me out downloading or a link to some programing software of any description for this radio. Cheers Rick.

Hello, i prefer www.radioarena.co.uk Best regards, Ludovic - F5PBG

Btw, 2000 ma rated 18650 cells are the jelly bean category of the family. Later versions are in the 3000 ma range with Panasonic the leader.? Be aware that there are two types of the cells, protected