Keyboard Shortcuts
ctrl + shift + ? :
Show all keyboard shortcuts
ctrl + g :
Navigate to a group
ctrl + shift + f :
Find
ctrl + / :
Quick actions
esc to dismiss
Likes
- Ic7000
- Messages
Search
|
Re: 10.7MHz IF Output?
dajetzi
You have to use the 1IF 124.487MHz.
toggle quoted message
Show quoted text
Here you go. Hope this helps a little. 73 de DO1KLM, Sigi --- In ic7000@..., "Chris" wrote:
|
|
Re: IC-7000 Won't transmit
Sounds exactly like the problem I had with my IC7000. All modes EXCEPT for SSB worked just fine. I sent it in to ICOM for repair. They found a the ALC ic to be bad. Cost me close to $200 for the fix including shipping charges.
toggle quoted message
Show quoted text
To be sure, check to see if it works on the VHF/UHF bands in FM mode. CW & RTTY modes should also show full power output if the problem is the same that I had. 73 - W3DRM - Don --- In ic7000@..., "Keith" wrote:
|
|
Re: 10.7MHz IF Output?
Hi All,
toggle quoted message
Show quoted text
I am a 7000 owner also interested in an attachment for panoramic reception. However, looking at the IC-7000 specs it seems that the 10.7MHz IF is used for WBFM only. My data sheet states that for all the other modes - SSB/CW/RTTY/NBFM - there are three IF's which are are 124.487MHz, 455kHz and 16.1kHz. The last two will be much too narrow for a panadaptor I suspect. I am working on the assumption that the way to go with the IC-7000 is to use a fully tunable HF SDR - I have an SDR-IQ - and control it via software like Studio 1 plus OmniRig. Tune the 7000 and the SDR tracks along or tune the SDR and the 7000 tracks along. Also, because the 7000 lacks an aux antenna output this means something like the Elad RF/AF switch box if one wants to connect to the same antenna. This approach does give quite a lot of extra flexibility over an IF panadaptor but with the SDR IQ does not provide for VHF/UHF reception. 73, Chris ZL1BOE --- In ic7000@..., "dajetzi" wrote:
|
|
[IC-7000] Re: 10.7MHz IF Output?
dajetzi
How is it possible you can post here when you can't into yahoo?
toggle quoted message
Show quoted text
Anyway, sent you a PM. 73 de DO1KLM, Sigi --- In ic7000@..., "C.Whitaker" wrote:
|
|
Re: [IC-7000] Re: 10.7MHz IF Output?
C.Whitaker
de WB2CPN
toggle quoted message
Show quoted text
I can't get into YAHOO. Any other way I can get that file? 73 Clete ++++++++++++++++++++++++ On 1/22/2013 7:14 AM, dajetzi wrote:
|
|
[IC-7000] Re: 10.7MHz IF Output?
dajetzi
Please report back your experience, especialy about the sensitivity loss which i already mentioned in the other thread.
toggle quoted message
Show quoted text
73 de DO1KLM, Sigi --- In ic7000@..., Mark Schoonover wrote:
|
|
Re: [IC-7000] IC-7000 Won't transmit
Were you able to test your setup into a dummy load bypassing the
antenna system completely ? Verify your coax cable jumpers with an ohmmeter. Let us know how you proceed.....Mac (w4glm) ________________________________ From: Keith <kd2cwq@...> To: ic7000@... Sent: Monday, January 21, 2013 1:16 PM Subject: [IC-7000] IC-7000 Won't transmit Hello and 73 to everyone.? I just joined the group and hope someone might have some input with the problem I'm having, it seems similar to the topic "Re: Strange issues with output power" This is the description of the problem I just sent to Icom: I plan to send my IC-7000 (S/N 0506030)in for repairs but thought I would give you some idea of the problem in the hope that you might be able to give me a preliminary assessment of the problem and range of cost. Other operating conditions: LDG AT7000 autotuner (found to be working properly) Buckmaster 300W 7-Band OCF dipole SWR (according to the internal meter) <= 1 on all HF bands OPEC 2M/440MHz dual band vertical antenna SSB RF level set to 100% I noticed that the ALC, Po, and COM meters were not moving when I tried to transmit on SSB.? As I tried to adjust the mic gain according to the instructions in the manual I found that there was no reading on the ALC meter and that adjusting the main knob had no effect on the meter reading. FM RF level set to 100% I was able to transmit on the 2M band but: - The ALC reading went full scale into the red - Attempts to adjust the ALC -- the ALC reading went full scale into the red when the PTT was activated and adjusting the main control know had no effect on the meter reading. -The strength of my transmission signal grew weaker as the transmission progressed. CW My Elmer, and former owner of the radio, transmitted a carrier and found the peak output to be 5W. I understand that you will be able to give a better assessment once you can test the radio but any preliminary thoughts would be appreciated. Sincerely, Keith Obrosky KD2CWQ 73! ------------------------------------ Community email addresses: ? Post message: IC7000@... ? Subscribe:? ? IC7000-subscribe@... ? Unsubscribe:? IC7000-unsubscribe@... ? List owner:? IC7000-owner@... ** "Spam, racism, name-calling, vulgarity, religious or political propaganda, personal insults and/or verbal abuse will not be tolerated in this group at any time. Any member posting such material will be placed on moderated status, and is subject to deletion and banning." ** Yahoo! Groups Links [Non-text portions of this message have been removed] |
|
Re: [IC-7000] Re: 10.7MHz IF Output?
Yes, this is exactly what I'm looking for. Thanks for the links.
73 - Mark Schoonover - KA6WKE QSX: 21.446 SSB & 29.6 FM On Sat, Jan 19, 2013 at 3:04 AM, dajetzi <da_kaeptn@...> wrote: ** [Non-text portions of this message have been removed] |
|
IC-7000 Won't transmit
Hello and 73 to everyone. I just joined the group and hope someone might have some input with the problem I'm having, it seems similar to the topic "Re: Strange issues with output power"
This is the description of the problem I just sent to Icom: I plan to send my IC-7000 (S/N 0506030)in for repairs but thought I would give you some idea of the problem in the hope that you might be able to give me a preliminary assessment of the problem and range of cost. Other operating conditions: LDG AT7000 autotuner (found to be working properly) Buckmaster 300W 7-Band OCF dipole SWR (according to the internal meter) <= 1 on all HF bands OPEC 2M/440MHz dual band vertical antenna SSB RF level set to 100% I noticed that the ALC, Po, and COM meters were not moving when I tried to transmit on SSB. As I tried to adjust the mic gain according to the instructions in the manual I found that there was no reading on the ALC meter and that adjusting the main knob had no effect on the meter reading. FM RF level set to 100% I was able to transmit on the 2M band but: - The ALC reading went full scale into the red - Attempts to adjust the ALC -- the ALC reading went full scale into the red when the PTT was activated and adjusting the main control know had no effect on the meter reading. -The strength of my transmission signal grew weaker as the transmission progressed. CW My Elmer, and former owner of the radio, transmitted a carrier and found the peak output to be 5W. I understand that you will be able to give a better assessment once you can test the radio but any preliminary thoughts would be appreciated. Sincerely, Keith Obrosky KD2CWQ 73! |
|
Re: [IC-7000] Re: IC-7000 don?t want to switch on
Ivan Silva
I advise to follow all the way from 12 v up to the control unit. I've fixed
two IC7000 that have had same problems in the metalizing of the holes on the printed circuit board where the thread passes from one side to the other side. Ivan-PY1YB _____ From: ic7000@... [mailto:ic7000@...] On Behalf Of VE3FMC Sent: sábado, 19 de janeiro de 2013 22:59 To: ic7000@... Subject: [IC-7000] Re: IC-7000 don?t want to switch on I had that problem once after I moved the radio. It was due to the fact that the face plate was loose, must have hit the release when I moved the radio. Reseated it and the radio was fine after that. Rick --- In ic7000@... <mailto:ic7000%40yahoogroups.com> , "dajetzi" wrote: 0g-ZzcStZC9L3fEmmQ5RAamc_bSgBsCei_D7ao8G-A_aAAaFw3HQ/ic7000-relay-click-\ click-no-power-problem.pdf> [Non-text portions of this message have been removed] |
|
Re: IC-7000 don?t want to switch on
VE3FMC
I had that problem once after I moved the radio. It was due to the fact that the face plate was loose, must have hit the release when I moved the radio. Reseated it and the radio was fine after that.
Rick --- In ic7000@..., "dajetzi" wrote: 0g-ZzcStZC9L3fEmmQ5RAamc_bSgBsCei_D7ao8G-A_aAAaFw3HQ/ic7000-relay-click-\ click-no-power-problem.pdf> |
|
Re: Retransmission of Received Audio
dajetzi
Hi,
toggle quoted message
Show quoted text
you're right. It is not possible with the trx itself. For this situations i am using HRD. 73 de DO1KLM, Sigi --- In ic7000@..., Eugene Coggins wrote:
|
|
Re: IC-7000 don?t want to switch on
dajetzi
Hello,
did the trx not switch on at all, means there is no display visible? How do you did a reset when trx did not switch on? Have you checked the contacts from the front panel? Maybe the display unit get short. Take a look here. Relay klicking <; 0g-ZzcStZC9L3fEmmQ5RAamc_bSgBsCei_D7ao8G-A_aAAaFw3HQ/ic7000-relay-click-\ click-no-power-problem.pdf> 73 de DO1KLM, Sigi |
|
Re: IC-7000 don?t want to switch on
Hi EA1RJ,
toggle quoted message
Show quoted text
Your friend problem like S21RC,but he solve the problem and repair it by himself. 73....VR2XXZ --- In ic7000@..., "ea1rj" wrote:
|
|
Re: [IC-7000] IC-7000 don?t want to switch on
Hi EA1RJ,
? ??? Your friend problem like S21RC,but he solve the problem and repair it by himself.? ? ? ? 73....VR2XXZ ? ? ?2013年1月19日 星期六，ea1rj <ea1rj@...> 寫道﹕ 寄件人: ea1rj <ea1rj@...> 主題: [IC-7000] IC-7000 don?t want to switch on 收件人: ic7000@... 日期: 2013年1月19日,星期六,下午3:27 ? Hi all i惴 new in the group, i had an IC-7000 during 2 years and i sold it, i think it愀 a great TRX (mine got the driver failure in guarente time) but it愀 realy a nice TRX. Noew i have one FT-2000 and one TS-2000X, enought for me :) I惴 trying to help a friend that don愒 speak english. Her IC-7000 don愒 want to switch on, when he press the on button, he ear the sound of a relay but the TRX don愒 switch on. we have check all fuses and we have made a reset but we have not found the mistake. Anyone can help us? tnx es 73 all [Non-text portions of this message have been removed] |
|
IC-7000 don?t want to switch on
ea1rj
Hi all
i?m new in the group, i had an IC-7000 during 2 years and i sold it, i think it?s a great TRX (mine got the driver failure in guarente time) but it?s realy a nice TRX. Noew i have one FT-2000 and one TS-2000X, enought for me :) I?m trying to help a friend that don?t speak english. Her IC-7000 don?t want to switch on, when he press the on button, he ear the sound of a relay but the TRX don?t switch on. we have check all fuses and we have made a reset but we have not found the mistake. Anyone can help us? tnx es 73 all |
|
Re: 10.7MHz IF Output?
dajetzi
Here is a pdf which shows how to find 1IF stage in IC7000
toggle quoted message
Show quoted text
Also a nice project you can find here. Panadapter for FT-817. --- In ic7000@..., Mark Schoonover wrote:
|
to navigate to use esc to dismiss