开云体育

There is a menu setting in the MFJ-929 that has to be set to "Icom" before it will work. It is described on page 19 of the manual. I got nailed by that little detail when I bought my MFJ-929 a couple

I dont seem to be able to connect the IC 7000 to my PW1 amp. The PW1 works fine with my IC775DSP, so its looks like it is not a failure of the PW1. Any help/suggestions appreciated. Iain ZL1IW

Got my 7000 back today from Scott Malcom, working perfectly and super well packaged for the trip back. It was sent for the random smoke issue.Driver replaced, bias readjusted, minor alignments.

Thanks Steve. I was pretty sure my 3 + year old Icom 7000 did not have that feature! Happy New Year 73, Rick VE3FMC

I received my 7000 back from the Michigan ICOM service center yesterday. Replaced PA and driver transistor and aligned under warranty. FB now. -Tom, W3TLN

That would be appreciated! It's a nuisance, but not impossible to reach across the table to get to the tuner 'tune' button. ;-) Hope you had a good Christmas, and all the best in the new year (that

Norm, I'll let you know after I talk to the tech at MFJ. He's out on vacation until the end of next week. But I think it is a timing problem since the TUNER light comes on but the tuner is not

Thanks, I did call MFJ but their tech is on vacation until the end of next week. I think you are correct, however, since I can see the TUNER icon but the tuner itself is not activated. I guess I will

Check with the builder of the tuner! I know that at least one tuner manufacturer had to come up with a different activation method for their product when the 7000 came out. * * * * * * * * * * * * 73

I don't think that is the problem since the tuner is powered from the IC-7000. Actually I have tried it both ways (wall wart and from the rig) and that doesn't seem to matter. I have the MFJ cable so

Thanks, I have the MFJ cable for the tuner so the power is supplied from the 7K. I also enabled PTT and that works okay but I didn't want to have to use that feature to get it to tune up. I also went

The tuner has to be powered on before you turn on the 7000 as the rig checks for an external tuner during its initialization. 73 de Perry K4PWO Sent on the Sprint? Now Network from my BlackBerry?

On 12/28/2012 9:38 AM, Dick wrote: > > I just purchased an IC-7000 along with an MFJ-929 auto tuner with Icom > cable and am not sure how this all works. I press the TUNER/CALL > button on the rig and

There are tuner settings in the 7k menu that need to be enabled. I enabled PTT so every time I hit PTT when going to a new freq it tunes and don't use tune button. Reminder the 7000 looks for a tuner

I just purchased an IC-7000 along with an MFJ-929 auto tuner with Icom cable and am not sure how this all works. I press the TUNER/CALL button on the rig and 'Tuner' shows on the display but nothing

Tks very much for the infos , happy newyear all. Jean luc ve2ced From: ic7000@... [mailto:ic7000@...] On Behalf Of Steve W3AHL Sent: Friday, December 28, 2012 9:01 AM To:

The "new feature" seems to only apply to new firmware updates available for the IC-7600 & 7800. I find nothing about TOT being available for the 7K. Icom doesn't update 7K firmware.... Steve, W3AHL

You have to use an interface to get recieved and transmit audio into and out of the radio. Easiest way is to use a sound card interface like you use to work PSK. I use a signal link and it works

→ A new feature, the Time-Out Timer (CI-V) function is added to the Others Set mod. Turns the Time-Out Timer function ON (3, 5, 10, 20 or 30 minutes) or OFF. Increased security: If a continuous

You do not adjust the ALC. If you have your mic gain adjusted properly the ALC should never go into the red section on the readout. If it is going there then you have too much mic gain. I can run the