开云体育

ctrl + shift + ? for shortcuts
© 2025 Groups.io
  1. Ic7000
  2. Messages
Expanded Topics Messages Polls
Date
Re: Port on back

 

Hi Dan,

I am successfully using software modems for both HF and V/UHF and I use the 13 pin connector. I also have HSEND & VSEND (Pins 3 &7) diode or-ed together so that I can use a single key line to active TX.

Regards,
Ralph
Port on back

 

I am trying to set up VARA FM with my 7000. Is it true for VHF I have to use the 6 pin data port on back and not the 13 pin port?
Can you still get rotary switches?

 

Just found the rotary switch on the bottom left of the faceplate (PBT/M-ch RIT) won't push in so I have limited capability to get to the memory channels.??

Looking to get a replacement.?

Will
KA3UQQ
Re: Icom exchange wanted

 

开云体育

No.? Its a local guy here in AZ that always comes up with gear and sells reasonably on ebay.??



Sent from my T-Mobile 5G Device



-------- Original message --------
From: "bobsayers2000 via groups.io" <bobsayers2000@...>
Date: 3/19/24 2:49 PM (GMT-07:00)
To: ic7000@groups.io
Subject: Re: [ic7000] Icom exchange wanted

Are those yours, Bill?




On Tue, 19 Mar 2024 at 20:45, Bill Kouchis
<bkouchis@...> wrote:
https://www.ebay.com/sch/i.html?_dkr=1&iconV2Request=true&_blrs=recall_filtering&_ssn=salvage-1_electronics&_oac=1&_pgn=1?



Sent from my T-Mobile 5G Device



-------- Original message --------
From: "bobsayers2000 via groups.io" <bobsayers2000@...>
Date: 3/19/24 1:34 PM (GMT-07:00)
To: ic7000@groups.io
Subject: [ic7000] Icom exchange wanted

Would like your IC-706 mk ll G in an exchange or part-exchange deal with my immaculate IC-7200, side handles, fitted leather case, all original accessories, large binder of manuals? reviews, mods.
?
A deal may only be possible in the UK due to high carriage costs, but try me anyway!
?
Re: Icom exchange wanted

bobsayers2000
 

Are those yours, Bill?




On Tue, 19 Mar 2024 at 20:45, Bill Kouchis
<bkouchis@...> wrote:
https://www.ebay.com/sch/i.html?_dkr=1&iconV2Request=true&_blrs=recall_filtering&_ssn=salvage-1_electronics&_oac=1&_pgn=1?



Sent from my T-Mobile 5G Device



-------- Original message --------
From: "bobsayers2000 via groups.io" <bobsayers2000@...>
Date: 3/19/24 1:34 PM (GMT-07:00)
To: ic7000@groups.io
Subject: [ic7000] Icom exchange wanted

Would like your IC-706 mk ll G in an exchange or part-exchange deal with my immaculate IC-7200, side handles, fitted leather case, all original accessories, large binder of manuals? reviews, mods.
?
A deal may only be possible in the UK due to high carriage costs, but try me anyway!
?
Re: Icom exchange wanted

 

开云体育

https://www.ebay.com/sch/i.html?_dkr=1&iconV2Request=true&_blrs=recall_filtering&_ssn=salvage-1_electronics&_oac=1&_pgn=1?



Sent from my T-Mobile 5G Device



-------- Original message --------
From: "bobsayers2000 via groups.io" <bobsayers2000@...>
Date: 3/19/24 1:34 PM (GMT-07:00)
To: ic7000@groups.io
Subject: [ic7000] Icom exchange wanted

Would like your IC-706 mk ll G in an exchange or part-exchange deal with my immaculate IC-7200, side handles, fitted leather case, all original accessories, large binder of manuals? reviews, mods.
?
A deal may only be possible in the UK due to high carriage costs, but try me anyway!
?
Icom exchange wanted

bobsayers2000
 

Would like your IC-706 mk ll G in an exchange or part-exchange deal with my immaculate IC-7200, side handles, fitted leather case, all original accessories, large binder of manuals? reviews, mods.
?
A deal may only be possible in the UK due to high carriage costs, but try me anyway!
?
Re: IC-7000 MODULATION IN FM/AM MODES

 

Likely its the first time you noticed this.??

ALC is not used for FM and AM modes its meaningless to them.

Also Every 7000 I've seen and my IC7300 has the same behaviour.

--
Allison
Re: IC-7000 MODULATION IN FM/AM MODES

 

I left some info out of my post. When selecting FM or AM modes the ALC maxes out, regardless of MIC gain settings. Works as expected using SSB.

Hopes this helps, Dennis ... AI6R
IC-7000 MODULATION IN FM/AM MODES

 

Hello Group, I think this is my first post here. My name is Dennis and my station call is AI6R.

First off I love my Icom 7000 and I use it weekly, but just recently it started miss behaving when using the FM or AM modes. It works OK using SSB.

I, at first thought, it might be the MIC or MIC cable, but since it works well in the SSB mode it would seem that the MIC and MIC cable are OK.

I've been through the manual several times looking for some setting that I might have set or changed. Nothing stood out as a proplem with any particular setting, but ...

Any advice on my particular problem would be much appreciated. I miss my evening nets on 2m's.

Thanks for any suggestions, Dennis ... AI6R
Re: IC 7000 repair

 

开云体育

A lot

On Mar 12, 2024, at 4:25?PM, Mike via groups.io <grizzletooth@...> wrote:

?The Icom Service Center in St. Joseph, MI.? Matt there is exceptional, reasonably priced and quick turnaround.


On Tue, Mar 12, 2024 at 2:43 PM, kc9c
<mark4bz@...> wrote:
I sent mine directly to Icom. The service was quick and reasonably priced.

Mark KC9C

On Tue, Mar 12, 2024 at 11:42?AM James Fisher via <cadiscase=yahoo.com@groups.io> wrote:
I live in Montana.
Where is a good place to send my IC 7000 in for repair ?

Thanks for any recommendations.

James

Re: IC 7000 damage

 

James,

Take your ohm meter and put it in diode mode. Test the power lead that goes into the radio for a short. Swap leads too. It's possible the short is inside the radio.

73! Mark KA6WKE - DM34st
Website:
Youtube:
Amateur Radio:
LinkedIn:?




On Tue, Mar 12, 2024 at 12:55?PM James Fisher via <cadiscase=yahoo.com@groups.io> wrote:


I own a IC 7000.? The? + 13.8 volt line touched the IC7000 ground.

How much damage can this do ?

I assume this has happened to others .

The radio draws a lot of current and will not turn on !

Thanks for any info.? (guesses)

James

Re: IC 7000 damage

 

Sounds like the finals are shorted and drawing excessive current.? I had a 706 years ago that the finals shorted and it drew a lot of current and got hot.

On Tuesday, March 12, 2024 at 02:55:34 PM CDT, James Fisher via groups.io <cadiscase@...> wrote:




I own a IC 7000.? The? + 13.8 volt line touched the IC7000 ground.

How much damage can this do ?

I assume this has happened to others .

The radio draws a lot of current and will not turn on !

Thanks for any info.? (guesses)

James

Re: IC 7000 repair

Mike
 

The Icom Service Center in St. Joseph, MI.? Matt there is exceptional, reasonably priced and quick turnaround.


On Tue, Mar 12, 2024 at 2:43 PM, kc9c
<mark4bz@...> wrote:
I sent mine directly to Icom. The service was quick and reasonably priced.

Mark KC9C

On Tue, Mar 12, 2024 at 11:42?AM James Fisher via <cadiscase=yahoo.com@groups.io> wrote:
I live in Montana.
Where is a good place to send my IC 7000 in for repair ?

Thanks for any recommendations.

James

Re: IC 7000 damage

Mike
 

Hopefully it as simy as you just popped a fuze.? Check all fuzes.? There us one on the face of the main portion of the radio behind that 1" square piece of black plastic, the two in-line fuzes, and i don't jnow if there are any internal where you'd have to separate the case.


On Tue, Mar 12, 2024 at 3:55 PM, James Fisher via groups.io
<cadiscase@...> wrote:


I own a IC 7000.? The? + 13.8 volt line touched the IC7000 ground.

How much damage can this do ?

I assume this has happened to others .

The radio draws a lot of current and will not turn on !

Thanks for any info.? (guesses)

James

Re: IC 7000 damage

 



I own a IC 7000.? The? + 13.8 volt line touched the IC7000 ground.

How much damage can this do ?

I assume this has happened to others .

The radio draws a lot of current and will not turn on !

Thanks for any info.? (guesses)

James

Re: IC 7000 repair

 

I sent mine directly to Icom. The service was quick and reasonably priced.

Mark KC9C

On Tue, Mar 12, 2024 at 11:42?AM James Fisher via <cadiscase=yahoo.com@groups.io> wrote:
I live in Montana.
Where is a good place to send my IC 7000 in for repair ?

Thanks for any recommendations.

James

IC 7000 repair

 

I live in Montana.
Where is a good place to send my IC 7000 in for repair ?

Thanks for any recommendations.

James
Re: Plastic Power Plug for IC-7000

Mike
 

Thank you!!!!!!


On Mon, Mar 11, 2024 at 11:20 PM, Bob KM4RL
<km4rl@...> wrote:
https://powerwerx.com/hf4-power-connector-cord-side

Re: Plastic Power Plug for IC-7000

 

https://powerwerx.com/hf4-power-connector-cord-side
521 - 540 of 42903