On Jul 23, 2021, at 13:25, Dan Smith - KK7DS via groups.io <dsmith@...> wrote:

Unfortunately, the saga continues. Would love some ideas on next steps.

After DigiKey and FedEx conspired against me, I finally received the replacement regulator and resistor that I needed to get the radio back together. I did that, and it happily powers up and seems to behave like normal -- on receive.

Now, when I transmit, I get weird behavior. On SSB with no modulation, power output reads almost half scale. However, on RTTY I get about 80% with RF power set to 100%.

The "power out with no modulation" behavior on SSB makes me think of self-oscillation, but I don't think it explains the RTTY "not full power" behavior. I pulled the covers off and re-sprung the ground springy things, but no difference. I wonder if the microprocessor resistor failure was actually a secondary effect of something in the TX path...

Any ideas?

--Dan

On Jul 11, 2021, at 9:37 PM, Dan Smith - KK7DS via groups.io <dsmith@...> wrote:

Well, sorry to be that guy that replies to his own emails. Further analysis for the archives:

I think I've got it worked out. Initially I was assuming there was something on the logic board that was drawing down the 3.3v line. So, I tried feeding the regulator input directly with the logic board not seated in the main board. That worked fine, with the regulator output at 3.3v and the input holding where I was feeding it. So, I thought maybe it was something on the main board drawing it to ground between the logic board connector and the head connector. There was no path to ground between pin 2 on the head connector that I could measure, so I seated the logic board back in the main board, with the main DC power disconnected and direct-fed the regulator on the logic board again. With that, I got a solid 3.3v at the head connector. However, if I powered the unit through the main DC connector, I'd get the same deal: low regulator HV input line, low regulator output, and low voltage at the head connector.

This led to me to think there was a high resistance in the path feeding the HV line. With no load, it would measure 14v, but under load it would draw down. I traced that to the PA board, where the HV line passes through EP703 (RFI choke I think) and R723, which I assume is a current limiting resistor to protect the always-on HV line. Measuring in-circuit, the choke was zero ohms (as expected), and R723 measured 52 ohms. It's marked in the service manual as 4.7. So, I bypassed R723 with a big and ugly 1/4 watt resistor of the lowest value from my stash (10 ohm) and...IT WORKED.

I haven't done any more checking on things other than that it now powers up and seems to be okay otherwise, but hopefully that's it. So, I've got to replace the regulator I removed, and get real good at microsurgery real fast so I can replace R723.

Longer-term I need to figure out if I want to keep this thing around once I get it patched up. I love it, but it seems like a ticking time bomb.

Still happy to hear any commentary on this and the previous analysis. Maybe all the issues I've had have something in common and fixing that would help this thing live a long life?

--Dan

On Jul 11, 2021, at 13:46, Dan Smith - KK7DS via groups.io <dsmith@...> wrote:

Hi all,

I'm looking for some help with my IC7000. I apologize for being wordy, it's in my nature and I can't help it. I'll provide a little background, in case it's relevant. If not, just skip to the problem description.

=== Background ===

I've used it quite a bit off an on over the years, but we have a bit of a dysfunctional relationship. I used to use it for a lot of portable (early days of SOTA) work in all kinds of conditions. It never got really wet or anything, and doesn't show any corrosion anywhere, but it has been outside quite a bit. Many years ago, it started doing this thing where it would just go deaf (all HF bands at least) on and off. Like, it would be sitting there in RX, showing S5 background noise, then ... silent S0 for ten minutes or so, then back to S5 like nothing happened. No touching, no external stimulus. I made a private youtube video showing it happen, wrote up a bunch of diagnosis and details, and sent it to Icom. They called me back, saying that they couldn't reproduce the problem, refused to look at the video, and thus were just sending it back to me with the ribbon cables reseated. I was super frustrated with this response (it was actually worse than I describe), so when I got it back, I literally put it on a shelf. A couple years later, I pulled it out to use it and got just the click-click-of-death thing. Back on the shelf, but later I diagnosed the shorted tantalum cap in the head, replaced, and it would power up. Back on the shelf without much use. Recently got it back out, and spent a day working it pretty hard on several bands and was thrilled to have my old friend back. Until it let me down again. On to the problem description:

=== Problem Description ===

Yesterday while working it, it started to power off when I would transmit. At one point it got into a really weird reboot loop where the relay that clicks on when you power it up would click on and off, on and off whenever it had external power. Click, click, click .. until I pull the power cable. No head input would stop it. Left it unplugged for a while and then it powered back on normally. Worked it for another hour and then it shut off again during transmit -- for would be the last time. After this, I get no click-click when I hit the power button, no activity at all when it is given power. Just totally dead like a brick. No burning smell either, for what it's worth.

=== Diagnosis ===

After much pouring over the service manual and tracing things out inside, I arrived at the IC1251 3.3v regulator on the logic unit. This (AFAICT) takes the 14v HV line and regulates it down to 3.3v to power the CPU and is required for the PWRK circuit to initiate the startup. This regulator was showing about 2.7v on the input and 2.4v on the output leg. Confirmed on the head connector pin 2 (with the head detached) that it's sitting at 2.4v instead of what I would expect to be 3.3v. I can probe the HV line on the main board right by the connector that feeds the logic board, and see that it sits at 14v when the logic board is out, and drops to 3.7v or so with the logic board in place. This indicates to me that something on the logic board is pulling that down real far.

I did what I could to check the bypass caps along the input and output lines to that regulator, but they're, uh, real small and stuff. So, I decided that a sane course of action would be to pop the regulator out so I could isolate before and after it. I got it out clean (although I pulled a leg off it so I'll have to replace that at least). As soon as I did, the HV line went back up to 14v, so I was hopeful that the regulator was bad. However, I wedged a TO-220 3.3v regulator from my parts box into the spot just to test, and it does the same thing. Without the output leg of the regulator connected to the board, it sits at 3.3v and the input sits at 14v. When I connect it to the output pad, it drops down and pulls the input with it, just like the original one.

As I mentioned, I tried to check what I could that is downstream of that regulator, specifically bypass caps C1252, C1317, C1317 although the latter two are so dang small I have no idea if I'm really on them. But, they don't seem to be shorted, best I can tell. The battery diode D1301 seems fine, and the battery voltage is 3.1v. Other than that, I'm at a bit of a dead end.

I assume I'm correct that ~2.4v at the head connector and output of the regulator is too low, and that the input shouldn't be pulled down that low, if not for something drawing a lot of current. Is that correct?

What else could I reasonably do to poke? Wild guesses, as well as informed ones, are welcomed.

Thanks!

--Dan

On Jul 11, 2021, at 9:37 PM, Dan Smith - KK7DS via groups.io <dsmith@...> wrote:

Well, sorry to be that guy that replies to his own emails. Further analysis for the archives:

I think I've got it worked out. Initially I was assuming there was something on the logic board that was drawing down the 3.3v line. So, I tried feeding the regulator input directly with the logic board not seated in the main board. That worked fine, with the regulator output at 3.3v and the input holding where I was feeding it. So, I thought maybe it was something on the main board drawing it to ground between the logic board connector and the head connector. There was no path to ground between pin 2 on the head connector that I could measure, so I seated the logic board back in the main board, with the main DC power disconnected and direct-fed the regulator on the logic board again. With that, I got a solid 3.3v at the head connector. However, if I powered the unit through the main DC connector, I'd get the same deal: low regulator HV input line, low regulator output, and low voltage at the head connector.

This led to me to think there was a high resistance in the path feeding the HV line. With no load, it would measure 14v, but under load it would draw down. I traced that to the PA board, where the HV line passes through EP703 (RFI choke I think) and R723, which I assume is a current limiting resistor to protect the always-on HV line. Measuring in-circuit, the choke was zero ohms (as expected), and R723 measured 52 ohms. It's marked in the service manual as 4.7. So, I bypassed R723 with a big and ugly 1/4 watt resistor of the lowest value from my stash (10 ohm) and...IT WORKED.

I haven't done any more checking on things other than that it now powers up and seems to be okay otherwise, but hopefully that's it. So, I've got to replace the regulator I removed, and get real good at microsurgery real fast so I can replace R723.

Longer-term I need to figure out if I want to keep this thing around once I get it patched up. I love it, but it seems like a ticking time bomb.

Still happy to hear any commentary on this and the previous analysis. Maybe all the issues I've had have something in common and fixing that would help this thing live a long life?

--Dan

On Jul 11, 2021, at 13:46, Dan Smith - KK7DS via groups.io <dsmith@...> wrote:

Hi all,

I'm looking for some help with my IC7000. I apologize for being wordy, it's in my nature and I can't help it. I'll provide a little background, in case it's relevant. If not, just skip to the problem description.

=== Background ===

I've used it quite a bit off an on over the years, but we have a bit of a dysfunctional relationship. I used to use it for a lot of portable (early days of SOTA) work in all kinds of conditions. It never got really wet or anything, and doesn't show any corrosion anywhere, but it has been outside quite a bit. Many years ago, it started doing this thing where it would just go deaf (all HF bands at least) on and off. Like, it would be sitting there in RX, showing S5 background noise, then ... silent S0 for ten minutes or so, then back to S5 like nothing happened. No touching, no external stimulus. I made a private youtube video showing it happen, wrote up a bunch of diagnosis and details, and sent it to Icom. They called me back, saying that they couldn't reproduce the problem, refused to look at the video, and thus were just sending it back to me with the ribbon cables reseated. I was super frustrated with this response (it was actually worse than I describe), so when I got it back, I literally put it on a shelf. A couple years later, I pulled it out to use it and got just the click-click-of-death thing. Back on the shelf, but later I diagnosed the shorted tantalum cap in the head, replaced, and it would power up. Back on the shelf without much use. Recently got it back out, and spent a day working it pretty hard on several bands and was thrilled to have my old friend back. Until it let me down again. On to the problem description:

=== Problem Description ===

Yesterday while working it, it started to power off when I would transmit. At one point it got into a really weird reboot loop where the relay that clicks on when you power it up would click on and off, on and off whenever it had external power. Click, click, click .. until I pull the power cable. No head input would stop it. Left it unplugged for a while and then it powered back on normally. Worked it for another hour and then it shut off again during transmit -- for would be the last time. After this, I get no click-click when I hit the power button, no activity at all when it is given power. Just totally dead like a brick. No burning smell either, for what it's worth.

=== Diagnosis ===

After much pouring over the service manual and tracing things out inside, I arrived at the IC1251 3.3v regulator on the logic unit. This (AFAICT) takes the 14v HV line and regulates it down to 3.3v to power the CPU and is required for the PWRK circuit to initiate the startup. This regulator was showing about 2.7v on the input and 2.4v on the output leg. Confirmed on the head connector pin 2 (with the head detached) that it's sitting at 2.4v instead of what I would expect to be 3.3v. I can probe the HV line on the main board right by the connector that feeds the logic board, and see that it sits at 14v when the logic board is out, and drops to 3.7v or so with the logic board in place. This indicates to me that something on the logic board is pulling that down real far.

I did what I could to check the bypass caps along the input and output lines to that regulator, but they're, uh, real small and stuff. So, I decided that a sane course of action would be to pop the regulator out so I could isolate before and after it. I got it out clean (although I pulled a leg off it so I'll have to replace that at least). As soon as I did, the HV line went back up to 14v, so I was hopeful that the regulator was bad. However, I wedged a TO-220 3.3v regulator from my parts box into the spot just to test, and it does the same thing. Without the output leg of the regulator connected to the board, it sits at 3.3v and the input sits at 14v. When I connect it to the output pad, it drops down and pulls the input with it, just like the original one.

As I mentioned, I tried to check what I could that is downstream of that regulator, specifically bypass caps C1252, C1317, C1317 although the latter two are so dang small I have no idea if I'm really on them. But, they don't seem to be shorted, best I can tell. The battery diode D1301 seems fine, and the battery voltage is 3.1v. Other than that, I'm at a bit of a dead end.

I assume I'm correct that ~2.4v at the head connector and output of the regulator is too low, and that the input shouldn't be pulled down that low, if not for something drawing a lot of current. Is that correct?

What else could I reasonably do to poke? Wild guesses, as well as informed ones, are welcomed.

Thanks!

--Dan

How serious are you about digging into the IC-7000?
Are you comfortable working on little bitty SMD devices and taking the radio apart?
I ask because working all through the drawings and troubleshooting does take a bit of effort.
The schematics are posted here I believe and tracking down the suggestion on the pull up resistor is a good start.?
However if the tracking is not going to be productive...
You could check the voltage on the PTT line on the accessory plug. If it is not high there then it can't be high deeper in the radio.
The same would apply to the mike PTT on the front and back.?
Data socket pin 3, Acc socket pin 3 HSEND pin 7 VSEND.
Pin 9 on the acc is the key line to the AT-180.
I think pin 6 on the mike jack.
The most likely points of failure are where the radio communicated with the outside world.

?

Hi.? Looked for any past posts, but didn't find them.?

Before the problem below developed, all control cables and coax disconnected (due to approaching storms), I have a disconnect area outside the house about 20 feet away.? I place the "house" bundle about 2 feet way from antenna area bundle of coax and various control lines to rotor, switches, etc.? SUSTAINED a lightning strike on the densely wooded hill behind me, may have hit an antenna, all 150 feet away.? But you could smell burnt wood, so some tree was hit.? Steep, rocky climb so not been up there yet.?

Results:? Wire damage and blown connector to the outdoor phone cable used.? This at the "disconnected end" of that remote switch run.? No other visible damage.??Inside, besides coming out of the chair from sound/flash from strike, no visible damage.? The lights barely blinked.? Multiple TVs, electronics in the house, and ALMOST all the equipment in the shack is still fine.? (1) The?station PC is dead.? YES ... audio, data, etc cables, connect EVERYTHING else in the shack to that PC.??Not the power supply, so the motherboard and beyond suspected.??

But to the point, (2)?the backup IC-7000 TX light stays lit RED, no sound out of speakers.? ?Output is fine.? CW keys.? SSB voice peaks show.? RTTY & FM go to normal power out.? All navigation through menus is normal.? I did a hard reset but same situation after that.? All connectors to the rig removed except for antenna coax -- and key during CW test, and Mic just for SSB test.

Any ideas?? Since all functioning of the unit otherwise looks good, power, processor, etc. ...? I hate to send it off before asking here.? Thanks.

Steve, W5KI

On Jul 11, 2021, at 13:46, Dan Smith - KK7DS via groups.io <dsmith@...> wrote:

Hi all,

I'm looking for some help with my IC7000. I apologize for being wordy, it's in my nature and I can't help it. I'll provide a little background, in case it's relevant. If not, just skip to the problem description.

=== Background ===

I've used it quite a bit off an on over the years, but we have a bit of a dysfunctional relationship. I used to use it for a lot of portable (early days of SOTA) work in all kinds of conditions. It never got really wet or anything, and doesn't show any corrosion anywhere, but it has been outside quite a bit. Many years ago, it started doing this thing where it would just go deaf (all HF bands at least) on and off. Like, it would be sitting there in RX, showing S5 background noise, then ... silent S0 for ten minutes or so, then back to S5 like nothing happened. No touching, no external stimulus. I made a private youtube video showing it happen, wrote up a bunch of diagnosis and details, and sent it to Icom. They called me back, saying that they couldn't reproduce the problem, refused to look at the video, and thus were just sending it back to me with the ribbon cables reseated. I was super frustrated with this response (it was actually worse than I describe), so when I got it back, I literally put it on a shelf. A couple years later, I pulled it out to use it and got just the click-click-of-death thing. Back on the shelf, but later I diagnosed the shorted tantalum cap in the head, replaced, and it would power up. Back on the shelf without much use. Recently got it back out, and spent a day working it pretty hard on several bands and was thrilled to have my old friend back. Until it let me down again. On to the problem description:

=== Problem Description ===

Yesterday while working it, it started to power off when I would transmit. At one point it got into a really weird reboot loop where the relay that clicks on when you power it up would click on and off, on and off whenever it had external power. Click, click, click .. until I pull the power cable. No head input would stop it. Left it unplugged for a while and then it powered back on normally. Worked it for another hour and then it shut off again during transmit -- for would be the last time. After this, I get no click-click when I hit the power button, no activity at all when it is given power. Just totally dead like a brick. No burning smell either, for what it's worth.

=== Diagnosis ===

After much pouring over the service manual and tracing things out inside, I arrived at the IC1251 3.3v regulator on the logic unit. This (AFAICT) takes the 14v HV line and regulates it down to 3.3v to power the CPU and is required for the PWRK circuit to initiate the startup. This regulator was showing about 2.7v on the input and 2.4v on the output leg. Confirmed on the head connector pin 2 (with the head detached) that it's sitting at 2.4v instead of what I would expect to be 3.3v. I can probe the HV line on the main board right by the connector that feeds the logic board, and see that it sits at 14v when the logic board is out, and drops to 3.7v or so with the logic board in place. This indicates to me that something on the logic board is pulling that down real far.

I did what I could to check the bypass caps along the input and output lines to that regulator, but they're, uh, real small and stuff. So, I decided that a sane course of action would be to pop the regulator out so I could isolate before and after it. I got it out clean (although I pulled a leg off it so I'll have to replace that at least). As soon as I did, the HV line went back up to 14v, so I was hopeful that the regulator was bad. However, I wedged a TO-220 3.3v regulator from my parts box into the spot just to test, and it does the same thing. Without the output leg of the regulator connected to the board, it sits at 3.3v and the input sits at 14v. When I connect it to the output pad, it drops down and pulls the input with it, just like the original one.

As I mentioned, I tried to check what I could that is downstream of that regulator, specifically bypass caps C1252, C1317, C1317 although the latter two are so dang small I have no idea if I'm really on them. But, they don't seem to be shorted, best I can tell. The battery diode D1301 seems fine, and the battery voltage is 3.1v. Other than that, I'm at a bit of a dead end.

I assume I'm correct that ~2.4v at the head connector and output of the regulator is too low, and that the input shouldn't be pulled down that low, if not for something drawing a lot of current. Is that correct?

What else could I reasonably do to poke? Wild guesses, as well as informed ones, are welcomed.

Thanks!

--Dan

?

Hi all, I am Deon ZS6RFI from South Africa.
I seem to have a problem to get my AH$ tuner working on my IC7000.
Is there any specific tricks to set up the tuner menus and so on I have tried some of the tuner settings on the radio but the tuner does not work at all.? It used to work quite well with my old IC706 MKIIG but no luck on the IC7000.?

I need some help.

Regards

Deon (ZS6RFI)?