开云体育

amp This is just what I am doing with my FT817 and HFPackr Amp. JA4AZS Ken

Does anyone know the function of the SQL pin on the ACC connector. I need a carrier operated sqelch type signal from the radio to indicate when a carrier has opened the squelch cct. Is this the SQL?

Hey Martin, send me your e-mail address and I will send you the PDF file for the QST article, it is 260k, not all that large of a file. Steve KA4NRF

Bob, You are correct in that there is a resistive pad in the amp's input stage that is bypassed when in receive mode. 73, Ken WB6MLC

Apologies if this was beaten to death before. I searched the archives and saw no resolution. When I connect my CT-62 to my FT-817 the noise level (FM, squelched) rises to S3-S7. Disconnected there is

Does the FT-817 have ARTS capability on VHF/UHF?

wrote: the Z11 off, then turn the amp on. I monitor the SWR on the FT817 meter. So far, pretty good. hmmmmm............... i would think that the swr between the rig and amp would always be close to

I have an FT-90P with the ARTS system in it. Does the FT-817 have ARTS in the VHF/UHF portion of the radio? Thanks and '&#, Fred W5FAE

I tune without amp, just the FT817 on AM or FM, 5 watts, then shut the Z11 off, then turn the amp on. I monitor the SWR on the FT817 meter. So far, pretty good. Rudy Marcelletti, K8SWD

hi - i completely agree with the suggestion of doing initial tune with amp in standby mode - tuner should easily handle the 50w output of the amp. bob / wk4rc amp in when tuning is

The relay are exactly the same in Z11 and RT11. May be it would have been happened anyway. The RF Problem in the CPU should be the same problem with the rt11, because the board seems to be the same.

I have a Yaesu FT90R with A(auto) R(ranging) T(transponder) S(system)...ARTS in it. Does the FT-817 have this system in it? I would use the FT-90R in one vehicle and the FT-817 in my other vehicle and

wrote: Yes, that is where it would be placed. I have used this combination for over a year with great success. You need to have the amp in bypass mode when you tune so the Z-11 is not switching high

I was testing at 60 watts and THAT is indeed too much, at least before matching has been achieved. I have one or more relays with bad contacts now. Cortland

Re: portable antenna in Australia I am currently investigating same options for my FT817 and will look up details on the "Joey" Nico, regarding QRP activity in Australia, you may find the VKZLQRP E

I had e-mailed LDG about what mods it would take to use the Z-11 with a 100 watt rig, Dwayne's reply was bigger torroids and there would be a problem with RF getting into the CPU. ARRL.org has a copy

You are correct as to placement. It works fine, but TUNE with the amp in STANBY/OFF, using only 2-3 watts from the barefoot FT-817, then, when tuning is COMPLETE, switch on the amp, and

Based on the ongoing discusions I would wait this out for a bit - I don't think its wise to just try it out ( I have and seem to have been lucky ). It indicates that with high SWR there is a chance of

Has anyone on the group used their FT-817 with a Z-11 autotuner and a Tokyo HiPower amp? I have all the components but have not yet tried them with the amp. I assume the tuner would be installed

Hi! What parts did blow when KA5S Tuner failed? Sorry I did not mention, I was testing 100W on a 10m piece of wire on all bands between 10m to 40m. I did this only for about 2 minutes, but in this