开云体育

Hello group has anyone had this problem. That the power button falls off ? KD6HNN Ken CM97

Ian,Worked correct for me.Rudiwa2nub To: FT817@... Sent: Saturday, November 12, 2016 1:52 PM Subject: [FT817] Re: Four ways to use the AlexLoop ? I have tried that link Alex but

Hi Ian, I have checked out a minute ago and it have worked to me. Please try again and tell me the results. https://www.youtube.com/watch?v=nnfbS-z-QRc 73 PY1AHD ALEX Alexandre Grimberg

I have tried that link Alex but end up with a you tube in Dutch on other topics but not the Alex Loop. Maybe you could re paste it and send again Thanks IanZL2AIM

IIRC, there is a tx inhibit on the CAT or audio port on the back. This message was delivered by flying monkeys!

I want to connect a receive only loop antenna and don't want to risk killing it if the 817 goes into transmit. Is there a way to inhibit the TX output. I could remove the mic so that the PTT is not

I have just posted a Youtube video showing four ways to use the AlexLoop. HTTPS://WWW.YOUTUBE.COM/WATCH?V=NNFBS-Z-QRC 1) Using the VIVITAR VIV-VPT-1250, the lightest and cheapest tripod on the

The left wing liberals here in California are doing everything they can to grind the 2nd amendment into the ground. ===================== Bill Jones – KD7S <>< Sanger,

I miss 6-Land especially in the winter. But to be honest the firearms laws would keep me from living there. 72/73 DR TIMOTHY-ALLEN ALBERTSON KD?OIA/(ex KG6IRH) FT817@...> wrote:

Hello Dr. Tim, Thank you for your response. Nowadays there are quite a few repeaters in the Santa Cruz area. I doubt I will have any difficulty finding one or more when I

I moved out of the bay area 11 years ago. I know there is a santa cruz repeater on 5150 buti i cant recall its specs. It used to tropo onto the 5150 repeater in SF. 72/73 DR TIMOTHY-ALLEN

Absolutely. The key point is how little current, 79mA or less, may be drawn from the CAT interface before the possibility, or likelihood, of a difficult and/or expensive repair. [Annoyingly,

I will be taking the maiden voyage in my new (used) motorhome to the Santa Cruz area next week. I would like to use my FT-817ND on 2-meters and 70cm. Are there any locals in the Santa Cruz/Felton

Hello Robin, The resistor rating has probably been chosen to act as a fuse, ie to burn up before anything else does, especially thin PCB traces, so uprate it at your peril. 73 Ken g8beq

G’day Eric, that’s what I thought – but the old brain just isn’t as reliable as it used to be Didn’t even think of looking at the schematic... 73 Steve VK2ARS Sent: Friday, November 11,

Hi Steve, I think you’ll find that the P2 doesn’t do anything. On the FT817, there are just the three specific lines on the mic socket being Up, Down and Fast so those are the only three

G’day, I have the above mic on my 817 (the DTMF is handy). The RJ45 locking tab on the mic lead broke, so I replaced it this morning and all is good EXCEPT I am having a brain fade on what

Adding to Dan's note, the resistor*R1235* is rated at *1/16W, 10Ω*, thus offering a maximum rated current of *79mA* before the resistor is overloaded. (Say 200Ω load max, more if the supply goes

Hi Jon, If the LED flashes, then the module is waiting for pairing. You need first to pair the Bluetooth module with your Android Device. You can do this from the Android System Settings or directly

Hi, You need to check if the resistor providing +13.8V power on the FT817 connector is not burned out. This is a very common issue with FT817. It is about R1235. To locate it check the following