¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
Date
Re: FB610 bandsaw blade position on the wheels: in the middle or near the edge?
You must have different wheels then what I've seen on a lot of Felder bandsaws. All were completely flat. Properly setup with proper tracking and blade tension results in no drift unless the blade is
By "[email protected] · #102166 ·
Re: FB610 bandsaw blade position on the wheels: in the middle or near the edge?
I follow Snodgrass's method on my 610. I tried the front of the wheel thing and it wouldn't cut straight. Using Alex's method it cuts straight. I find it easier to adjust the tracking than adjust for
By David · #102165 ·
Re: Shims for Felder dado set
Think those are the correct ones but you could always give Felder a quick call and confirm that they are the correct ones.
By David · #102164 ·
Re: Integrated adjustable rollers for AD 951
The only time I thought bed rollers were worth the effort was when they were powered. Few are now so I'd save the 750 unless you run really rough stock. Dave ________________________________ Sent:
By David Kumm · #102163 ·
Re: Replacement Nordfab Seal Material
Frost King V23WA Ribbed Rubber Self-Stick Weatherseal Tape, 3/8" W, 1/8" T, 17 ft L, White https://www.amazon.com/dp/B000OZT84K/ref=cm_sw_r_cp_apa_i_ougtEbJ87DGHB This works great for 5 and 6 inch
By Marlowe McGraw · #102162 ·
Integrated adjustable rollers for AD 951
Integrated adjustable rollers for AD 951 is a feature offered for the Felder 951. Anyone have experience with using this machine with and without this feature? It's an upcharge of $750. I have always
By Acharya Kumarnathaswami · #102161 ·
Re: Replacement Nordfab Seal Material
Definitely not as easy to reconfigure the spiral compared to clamp together especially if you need to change something in the middle of a run, not sure if it¡¯s worth 4-5 times the cost of spiral
By Mark Kessler · #102160 ·
Re: FB610 bandsaw blade position on the wheels: in the middle or near the edge?
I own a Felder FB 510 and have run my tyres centrally - without realising the profile is close to flat rather than crowned as some posters have pointed out. But I have experienced no issues. My
By Brian Rowland · #102159 ·
Re: Replacement Nordfab Seal Material
I really like the Nordfab ducts.? I reconfigure it for new machines and took less than an hour.? I don't think you can do it as easily with spiral ducts when I was researching the two options.?
By Shinta Wakahisa · #102158 ·
Re: Felder overhead guard vs. riving knife mounted guard
Not mine but figured I¡¯d share in case this is of interest to someone here. https://reading.craigslist.org/tls/d/pottstown-biesemeyer-square-tablesaw/7077892823.html Ron Magliocco 1-203-216-4629
By Ron Magliocco <rmagliocco2@...> · #102157 ·
Re: Felder overhead guard vs. riving knife mounted guard
I have used both, and I have also used Sharkguard by Lee Valley. my opinion and experience is that overhead guard are more superior than the standard type. there are times a standard one may work
By Albert Lee · #102156 ·
FB610 bandsaw blade position on the wheels: in the middle or near the edge?
I was curious about the recommendation here is.? I recently saw a video by Alex Snodgrass where he recommends positioning the blade gullet at the center of the wheels as it gets the most support
Shims for Felder dado set
All I currently have this Felder dado set ( http://us.feldershop.com/en-US/en-US/en-US/Sawing/Tongue-and-groove-cutters/Adjustable-Dado-Cutter-for-Saw-Unit-RB-HW.html ) , but misplaced the shims
By Anil · #102154 ·
Re: Replacement Nordfab Seal Material
Timely post as i will be asking some questions about norfab vs spiral. Why not just buy replacement nordfab o rings? Maybe mentioned and I missed it Regards, Mark
By Mark Kessler · #102153 ·
Re: Replacement Nordfab Seal Material
I've replaced some of mine with the white roll sticky backed seal material that you can get at home depot or Lowe's. I'll try to look up the specific details later. Marlowe McGraw
By Marlowe McGraw · #102152 ·
Re: I did something stupid!
It might vary by model.? My PP has voltage to ground on two legs when "off".? The Phase Perfect PT manual repeats this warning in multiple places: *WARNING! When the converter is turned OFF using a
By mark thomas · #102151 ·
Re: Replacement Nordfab Seal Material
If you don't plan on taking it apart? why not use silicone sealant?
By Cliff Rohrabacher, Esq. <rohrabacher@...> · #102150 ·
Re: I did something stupid!
Yes that¡¯s how you get around it martin/campshure/co/llc mac campshure 7412 elmwood ave. middleton, wi 53562-3106 608-332-2330 cell 608-824-0023 fax airtightclamps@... airtightclamps.com
By Airtight: Clamps by Air Compression · #102149 ·
Re: I did something stupid!
My AR has that accessory feature for two thirds the cost of the unit so I am just installing 0/1 every 16 feet to start with incase my brain takes a dump. I probably have every thing on my shelves to
By Airtight: Clamps by Air Compression · #102148 ·
Re: I did something stupid!
Hi SW, Felder, like many other equipment suppliers don¡¯t want unqualified persons messing around with the guts of the machines while they are under warranty. It tends to unnecessarily complicate
By Alex Bowlds · #102147 ·