开云体育

I finally had some time to finish up my Copy Stick. ? Many thanks to those who shared their own versions and especially to David Best who graciously shared multiple iterations of his design. My

What are the details on the shopsabre? B+ [email protected]> wrote:

Still available and I'm open to offers. I also have a ShopSabre 23 I'll be selling as well as a Hammer A3-31, Oneida Supercell w/ Nordfab ducting and a Jessem router table. The ShopSabre is ready to

I have an F coupling mounting head, but if he wants the old style rod and such, those are long gone. It would be a linear rail now. Brian Lambblamb11@...

I would think that Brian could help you out with that he must still make them for the F coupling, Mac,,, martin/campshure/co/llc mac campshure 7412 elmwood ave. middleton, wi 53562-3106 608-332-2330

The cutters and the bushings that fit on the shaft should fit on it pretty snug. I wouldn’t advise using any anti-seize as those parts do not move if you’re sleeves and are so snug that they

If you have polished off the galled spots on the shaft and the cutters, then I would add some anti-seize when you put a cutter on there and make sure you lock it down tight and you don't have anything

My CF 731 has a dust collector polycarbonate shroud around the cutter head on the spindle moulder (shaper). This became dislodged and collided with a large rebate (rabbet) cutter , 150mm x 50mm (6" x

Hi Mike, If the hose exits low on the cabinet, why do you need to mess with the PF. In my case, The hose exits thru the tilt bracket. May be a picture will help. If you rest the PF on the cast iron

Update: Bought Metabo NP50A, it is $120 on Amazon: https://a.co/d/bs8f4Uc At 80 PSI it drove 1 3/8” pins consistently. It is advertised to handle up to 2” but 1 3/8” is the longest I had as

Thanks Imran. My power feeder too is resting .? My 2008 machine also rests on the F rail, but has an. 80 mm hose which is? longer, as it goes down to the bottom edge of the cabinet. Based on your

Long ago, Felder made a male / female dovetail fitting extension piece in cast iron to extend the capacity of the rip fence on the universal machine. Neglectfully I never bought one at the time, but

That's how Harvey delivered my dust collector. I had the audacity to assume it was standard. Stan Sent from Proton Mail for iOS On Wed, Apr 23, 2025 at 08:20, Larry Long Neck via groups.io

Does anyone have a Lamb Tool Works old style Parallel Fence they would like to sell? I need the F-style. Thanks. John H

As it was mentioned earlier here, Nova’s US arm is going thru chapter 11 reorganization. Appears they liquidated Nova Viking via Grizzly. It cost me $1187 delivered with lift gate charge ($500 off

Here you go Mike. Re: Felder Disintegrating Hose groups.io Imran Malik IAM Wood Creations https://www.facebook.com/groups/362481112015700/?ref=share

That is what they use a lot in EU, makes delivery so much easier indeed. I have not seen them in the US at all (at least not at my almost ending two weeks in Las Vegas). Kind regards, Jonathan

I posted replacing this hose few months ago. I was able to do it without removing the power feeder. I had to remove the 2 studs and pull out the plastic cover. I am not sure if the plastic cover

Wow, that was spot on Imran.? I? have no idea how you figured that out.?? Best I can tell, it is an exact replacement for that part (although I did not remove the existing part). Thanks, Aaron

I see from searching that the main hose replacement has been discussed quite a bit, but my 2008 machine main hose is in good shape. However, the 100 mm hose from the shaper cavity just under the saw