开云体育

Hi Imran! Yes, based on my research and experience it appears that the following is generally true in terms of Felder/Aigner compatibility: -- When the Felder table extension mounting bars (TEMB) are

David, Good point on soft start. In the number I posted both K975 and Dual51 have star-delta start. Imran

The three phase higher hp felder motors I've seen are soft start so starting the rpc will be the limitation, not the machines. I have 110 amps going to the garage shop and can run about 20 hp at the

Hi Steve, Attached shows what the plastic dust collector "basket" should look like. I just posted measured currents of motors including 5.5KW and this might help you in determining your head room. The

I thought this might help folks make an informed decision when sizing a phase converter, especially when the single phase power available in the shop is limited. Actual motor currents are usually much

Guys just piddling around in shop and it occurred to me to check how far back my fence plates go. When I mount the hood in the rear set of holes, the fence plates actually sits behind the centerline

Thanks Tom for the pics. Looks like I can fit the pressure module and extension table if I switch from Aigner to Felder rails. Here is a pic showing ext. table not fitting on Aigner rail. The rail is

Hi Joe! I added the Felder mounting rails to my little Laguna 14" saw and have been really happy with the utility they've added to the machine. The apron on the cast iron top wasn't tall enough to

Yea, was planning on getting better footage but the ops manager popped into the area, i mean of all places - the building is huge with hundreds of machines on top of each other and he happened come by

These pocket doors came up in discussions a while back https://www.cavitysliders.com/Contact?utm_source=risingerbuild&utm_medium=youtube&utm_campaign=risingerbuild_cspocketdoor

Thank for clarification Mark. It was hard to see what’s going on ….. Sent: Saturday, March 06, 2021 11:10 AM To: [email protected] Subject: Re: [FOG] zci for k940 Hi Imran, Wire edm is

Hi Imran, Wire edm is done submerged, the video shown is the cnc’ing after the edm Regards, Mark https://www.instagram.com/kessler_woodworks/?hl=en

Looking good. I have not seen wire EDM in person but read up some time ago and was under the impression that it is always done submerged. Apparently it can be done with just abundant fluid as well.

I have the same sliding table on a K500 and you cannot if you plan to clamp on both ends. With clamp, the minium is 2800mm to cut 8 ft board,?if your clamp bases are not too big. According to many

I am thinking about trading up to a k700p with the 2500mm slider.? Is cutting a sheet of melamine which is 2460 long do able on the saw including the scoring blade.? I currently have a k3 winner

Thanks Patrick & Imran for your thoughts. I was excited to see this saw come up in the Seattle market local to me, but then found it to be so-so in person. It's missing an eccentric clamp, table saw

I am looking at selling my k3 winner 2000mm slider and purchasing a k700p with the 2500 mm slider.? Would the 2500mm slider on the thee k700p by able to cut the untire length for a 2460mm long sheet

Joe, I mounted Aigner rails on my bandsaw for Aigner pressure wheels following Aigner directions. Later I realize that my felder cast iron extension tables don’t fit. Maybe, I could have mounted the

I’m a big fan of KN Crowder products. Here is a link to there barn door systems: http://www.kncrowder.com/slidingdoor/#barnDoor <http://www.kncrowder.com/slidingdoor/#barnDoor> You may or may not

Hi, My wife wants me to replace her pantry door with a barn door. She wants it painted so I was just going to make it out of 6/4 popular. She likes the soft close/open feature. Any suggestions on