¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
  1. Felderownersgroup
  2. Messages
Expanded Topics Messages Polls
Date
Re: Spindle Sander

 

Thanks David. I suspected that I could not slow the shaper adequately. My heart is set on oscillating spindle Sander with cast iron table but it is way down on priority list. I had heard and read that Rigid is a pretty good unit.
Re: Electrical question

 

¿ªÔÆÌåÓý

208 is common along with 220?
Basically the lower the volts the higher the amp draw and of course larger wires with lower volts. ?
You can put buck and boost to jack currents up i.e. 208 to 220.?
If you put in panels I would go with SqD QOND boxes. They give you a lot ?more work space in the box.
I run all 1" conduit and no 10 wire ?except where larger is needed.?
This way you can ether buy or salvage one size.?
I just inventory straight pipe connectors 90 elbows and off sets and us 6x6x6 smallest for junctions.?
Get yourself set of greenleee punches.
Mac,,,





martin/campshure/co/llc
mac campshure
7412 elmwood ave.
middleton, wi 53562-3106
608-332-2330?cell

Designing and building for 47 years


On Dec 6, 2016, at 9:45 PM, GLEN chris3645@... [felder-woodworking] <felder-woodworking@...> wrote:

?

I have a question regarding 3 phase power, as some of you know I am trying to decide between Felder and Martin. A s I am trying to work out the little details, I am questioning the power that my new building really has. I was told I have 400 amps but I was not told what the 3 phase is< 208,277,240,or 480. I called an electical contractor in the area to find out but have not heard back. I talked to my electrician here and over a very broken cell phone conection he tried to explain the differences are and how the can be manipulated to the machines I want to buy.
My bottom line ..It was way over my head.
The building I am renting the landlord thinks its 208 I don't think that is correct.
?
Any help would be greatly appreciated

I am looking at Format machines for the shop but my largest machine is 230/19 kw @ 25 HP

Thank you all
Glen


-----Original Message-----
From: Marlowe McGraw marlomcgraw@... [felder-woodworking] <felder-woodworking@...>
To: felder-woodworking <felder-woodworking@...>
Sent: Tue, Dec 6, 2016 7:18 pm
Subject: Re: [felder-woodworking] Standard motor ok for VFD?

?
Thanks Brian,
I will likely feed at the same range as original.? Should be the highest speed when I couple the motor to the gearbox?

Marlowe

On Tue, Dec 6, 2016 at 9:05 PM, Brian Lamb blamb11@... [felder-woodworking] <felder-woodworking@...> wrote:
?
Pretty much any current manufacture motor will run on a VFD, the trick is how much above and below the standard 60hz you can run. I would say from 30hz to 120hz on most motors. My CNC mill runs from 10hz or so on the low end to 200 hz on the high, and I¡¯ve seen some inverter rated motors that run up to 400hz. You just need to determine how much over/under speed ratio you want to accomplish the feeds you need, and see if that works for your motor.

Brian Lamb




On Dec 6, 2016, at 7:36 PM, Marlowe McGraw marlomcgraw@... [felder-woodworking] <felder-woodworking@yahoogroups.com> wrote:


I am considering replacing an uber complex mechanical variable speed drive (feed system on a Griggio planer) with a VFD.? I already bought a new C faced 3 phase motor and have a drive that will work , but was wondering if it needs to be a motor of any special duty rating, etc.

Marlowe McGraw?

Re: Spindle Sander

 

¿ªÔÆÌåÓý

Yes, I have used them and sold them off. ?They run too fast, don¡¯t oscillate, burn up paper quickly. ? This is a better alternative IMO:


David Best

On Dec 6, 2016, at 7:25 PM, imranindiana@... [felder-woodworking] <felder-woodworking@...> wrote:

Has anyone used Felder schleiffix sanding drums? They are in xmas catalog. I will have to go to the shop to check how slow I can run the shaper. I would also like to know if paper is held well by this device and if felder paper being offered is good.

Thanks, Imran
Re: Spindle Sander

 

¿ªÔÆÌåÓý

Yes, I have used them and sold them off. ?They run too fast, don¡¯t oscillate, burn up paper quickly. ? This is a better alternative IMO:


David Best

On Dec 6, 2016, at 7:25 PM, imranindiana@... [felder-woodworking] <felder-woodworking@...> wrote:

Has anyone used Felder schleiffix sanding drums? They are in xmas catalog. I will have to go to the shop to check how slow I can run the shaper. I would also like to know if paper is held well by this device and if felder paper being offered is good.

Thanks, Imran
Electrical question

GLEN
 

I have a question regarding 3 phase power, as some of you know I am trying to decide between Felder and Martin. A s I am trying to work out the little details, I am questioning the power that my new building really has. I was told I have 400 amps but I was not told what the 3 phase is< 208,277,240,or 480. I called an electical contractor in the area to find out but have not heard back. I talked to my electrician here and over a very broken cell phone conection he tried to explain the differences are and how the can be manipulated to the machines I want to buy.
My bottom line ..It was way over my head.
The building I am renting the landlord thinks its 208 I don't think that is correct.
?
Any help would be greatly appreciated

I am looking at Format machines for the shop but my largest machine is 230/19 kw @ 25 HP

Thank you all
Glen


-----Original Message-----
From: Marlowe McGraw marlomcgraw@... [felder-woodworking]
To: felder-woodworking
Sent: Tue, Dec 6, 2016 7:18 pm
Subject: Re: [felder-woodworking] Standard motor ok for VFD?

?
Thanks Brian,
I will likely feed at the same range as original.? Should be the highest speed when I couple the motor to the gearbox?

Marlowe

On Tue, Dec 6, 2016 at 9:05 PM, Brian Lamb blamb11@... [felder-woodworking] <felder-woodworking@...> wrote:
?
Pretty much any current manufacture motor will run on a VFD, the trick is how much above and below the standard 60hz you can run. I would say from 30hz to 120hz on most motors. My CNC mill runs from 10hz or so on the low end to 200 hz on the high, and I¡¯ve seen some inverter rated motors that run up to 400hz. You just need to determine how much over/under speed ratio you want to accomplish the feeds you need, and see if that works for your motor.

Brian Lamb




On Dec 6, 2016, at 7:36 PM, Marlowe McGraw marlomcgraw@... [felder-woodworking] <felder-woodworking@yahoogroups.com> wrote:


I am considering replacing an uber complex mechanical variable speed drive (feed system on a Griggio planer) with a VFD.? I already bought a new C faced 3 phase motor and have a drive that will work , but was wondering if it needs to be a motor of any special duty rating, etc.

Marlowe McGraw?

Spindle Sander

 

Has anyone used Felder schleiffix sanding drums? They are in xmas catalog. I will have to go to the shop to check how slow I can run the shaper. I would also like to know if paper is held well by this device and if felder paper being offered is good.

Thanks, Imran
Re: Standard motor ok for VFD?

 

Thanks Brian,
I will likely feed at the same range as original.? Should be the highest speed when I couple the motor to the gearbox?

Marlowe

On Tue, Dec 6, 2016 at 9:05 PM, Brian Lamb blamb11@... [felder-woodworking] <felder-woodworking@...> wrote:
?

Pretty much any current manufacture motor will run on a VFD, the trick is how much above and below the standard 60hz you can run. I would say from 30hz to 120hz on most motors. My CNC mill runs from 10hz or so on the low end to 200 hz on the high, and I¡¯ve seen some inverter rated motors that run up to 400hz. You just need to determine how much over/under speed ratio you want to accomplish the feeds you need, and see if that works for your motor.


Brian Lamb




On Dec 6, 2016, at 7:36 PM, Marlowe McGraw marlomcgraw@... [felder-woodworking] <felder-woodworking@yahoogroups.com> wrote:


I am considering replacing an uber complex mechanical variable speed drive (feed system on a Griggio planer) with a VFD.? I already bought a new C faced 3 phase motor and have a drive that will work , but was wondering if it needs to be a motor of any special duty rating, etc.

Marlowe McGraw?
Re: Standard motor ok for VFD?

 

¿ªÔÆÌåÓý

Pretty much any current manufacture motor will run on a VFD, the trick is how much above and below the standard 60hz you can run. I would say from 30hz to 120hz on most motors. My CNC mill runs from 10hz or so on the low end to 200 hz on the high, and I¡¯ve seen some inverter rated motors that run up to 400hz. You just need to determine how much over/under speed ratio you want to accomplish the feeds you need, and see if that works for your motor.

Brian Lamb




On Dec 6, 2016, at 7:36 PM, Marlowe McGraw marlomcgraw@... [felder-woodworking] <felder-woodworking@...> wrote:


I am considering replacing an uber complex mechanical variable speed drive (feed system on a Griggio planer) with a VFD.? I already bought a new C faced 3 phase motor and have a drive that will work , but was wondering if it needs to be a motor of any special duty rating, etc.

Marlowe McGraw?
Standard motor ok for VFD?

 

I am considering replacing an uber complex mechanical variable speed drive (feed system on a Griggio planer) with a VFD.? I already bought a new C faced 3 phase motor and have a drive that will work , but was wondering if it needs to be a motor of any special duty rating, etc.

Marlowe McGraw?
Christmas Specials 2016 - Felder Group

[email protected]
 

Dear Members


Time to take advantage of great year end deals, not only on machines but tools and accessories also.?


E Shop specials:?


Sales PDF:?


Felder Group web page:?


Happy Woodworking?
Re: Extension Table

 

This is what I use and it works well.? Also used on bandsaw.

Julie


From: "Brian Lamb blamb11@... [felder-woodworking]"
To: FOG <felder-woodworking@...>
Sent: Tuesday, 6 December 2016, 0:43
Subject: Re: [felder-woodworking] Extension Table

?
Pretty sure that¡¯s F-channel. Felder sells a 1 meter extension table with a leg for that position. Take a look at this on the Felder site:



Brian Lamb
blamb11@...
www.lambtoolworks.com




On Dec 5, 2016, at 5:32 PM, wildcoach@... [felder-woodworking] wrote:


Hi Everyone,

I have a current year KF700SP (delivered 2016) and want to put an extension table at the end of the shaper outfeed but I don't know what connection type that is.? There is a short connection bar that is used to attach the power feeder lift that has room for a small width outfeed table.? Can anyone tell me what style of connection that is and whether Felder makes an extension table for this point? I see a couple in the catalogue, but can't tell which one would work for my application.

Alternatively, if some other company makes an outfeed table, or there are plans to make one, please let me know.

Using a power feeder on the shaper without an extension table provides very little room to catch the outfeed stock, plus I worry that longer stock will get pulled down by gravity at the leading edge and lift up the stock at the cutter head.

As always, your assistance and advice is really appreciated.

Warmly,

Bill White
SoCal (Orange County)
Re: Extension Table

George
 

¿ªÔÆÌåÓý

I don't know if this is suitable for a shaper, but it works great for my jointer. General International out of Canada has collapsible accordion style roller stands that collapse down to about 2 foot and expand to around 6 foot. All 4 legs are independently adjustable and have a measuring scale on them for repeatability. The wheels also lock. I put marks on my floor where each wheel goes and leave the legs at the same adjustment. I can have both the infeed and outfeed ?sides set up and ready to go in probably less than 5 minutes. Each leg is infinitely adjustable , so you can really tweak them in to your machine. I have milled 12 foot lengths of lumber pretty darn flat and feel I could do the same with even longer if I had some. When I'm done with the long stuff they can be collapsed and rolled out the way in no time. I also have another one that I use on the infeed side of my cabinet saw. Works great. Just a thought. George Gerstner, Ostrander, Ohio



On Dec 5, 2016, at 7:52 PM, patrick walsh pwalsh651@... [felder-woodworking] <felder-woodworking@...> wrote:

?

I just went through this.


I opted for the Aigner tables over the Felder. They are very?nice although mine arrived with a couple lumps or blemishes in them. Almost like where the?brackets for the legs got welded to the tables bottom?it caused the?aluminum to?deform. Its kinda?a bummer but they are really really nice otherwise.

The F style bracket is what you want to mount either the Felder or Aigner tables. The Felder ones are on sale at the moment. Even on sale they are more expnsive than the Aigner and imop the Aigner are nicer.

Call Felder in Delaware and ask for Geoff Dubet in sales. He is a great guy and will get you exactly what you need for your exact machine..

?

On Monday, December 5, 2016, Brian Lamb blamb11@... [felder-woodworking] <felder-woodworking@...> wrote:
?

Pretty sure that¡¯s F-channel. Felder sells a 1 meter extension table with a leg for that position. Take a look at this on the Felder site:




Brian Lamb




On Dec 5, 2016, at 5:32 PM, wildcoach@... [felder-woodworking] <felder-woodworking@yahoogroups.com> wrote:


Hi Everyone,


I have a current year KF700SP (delivered 2016) and want to put an extension table at the end of the shaper outfeed but I don't know what connection type that is.? There is a short connection bar that is used to attach the power feeder lift that has room for a small width outfeed table.? Can anyone tell me what style of connection that is and whether Felder makes an extension table for this point? I see a couple in the catalogue, but can't tell which one would work for my application.

Alternatively, if some other company makes an outfeed table, or there are plans to make one, please let me know.

Using a power feeder on the shaper without an extension table provides very little room to catch the outfeed stock, plus I worry that longer stock will get pulled down by gravity at the leading edge and lift up the stock at the cutter head.

As always, your assistance and advice is really appreciated.

Warmly,

Bill White
SoCal (Orange County)
Re: Extension Table

 

¿ªÔÆÌåÓý

I bought them from Martin in US when our dollar was in better shape. I do have that mounting piece for the round bar to F rails ?that Dave mentioned if you find your interested in getting one. I needed it when I had my AD741.?



John
JMK Services?




-------- Original message --------
From: "James Zhu james.zhu2@... [felder-woodworking]" <felder-woodworking@...>
Date: 2016-12-05 10:26 PM (GMT-05:00)
To: "phil_moger@... [felder-woodworking]" <felder-woodworking@...>
Subject: Re: [felder-woodworking] Extension Table

?

John,

Where did you buy the Aigner product in Canada?

Thanks,
James

On Mon, Dec 5, 2016 at 9:49 PM, John jmkserv@... [felder-woodworking] <felder-woodworking@...> wrote:
?

I did the same basically 2 for the price of 1 Felder. I use them on the FB600, F700Z, and my AD951.?


John
JMK Services?




-------- Original message --------
From: "David Davies myfinishingtouch@... [felder-woodworking]" <felder-woodworking@yahoogroups.com>
Date: 2016-12-05 9:34 PM (GMT-05:00)
To: felder-woodworking <felder-woodworking@yahoogroups.com>
Subject: Re: [felder-woodworking] Extension Table

?

I ended up buying an Aigner extension fence from Carl at Martin.? I can't remember exactly ?now and their e-shop is down but I think it was about half the price of the Felder.

On Mon, Dec 5, 2016 at 7:36 PM, mac campshure mac512002@... [felder-woodworking] <felder-woodworking@yahoogroups.com> wrote:
?

I find it utterly amazing that you purchased a machine and an extension table at a minimum ?6x20"cast table was not part of your purchased.
?The table ends abruptly in less than a foot from spindle center line.
This is the responsibility of your sales person,,, period.
Like buying a saw with no blades what the hell. ?
mac...
?
martin/campshure/co/llc
mac campshure
7412 elmwood ave.
middleton, wi 53562-3106
608-332-2330 cell
airtightclamps@...

Designing and building for 46 years


From: "James Zhu james.zhu2@... [felder-woodworking]" <felder-woodworking@yahoogroups.com>
To: felder-woodworking@yahoogroups.com
Sent: Monday, December 5, 2016 7:18 PM
Subject: Re: [felder-woodworking] Extension Table

?
I observed the same thing, extension table is 100% needed on the KF 700. I need to order one too.

I think it is F-channel extension table.

I have the wide aluminum F-channel extension table, I use it on planer and bandsaw, but too wide, can't use it on the outfeed end of the KF.

James



On Mon, Dec 5, 2016 at 7:32 PM wildcoach@... [felder-woodworking] <felder-woodworking@yahoogroups.com> wrote:
?
Hi Everyone,

I have a current year KF700SP (delivered 2016) and want to put an extension table at the end of the shaper outfeed but I don't know what connection type that is.? There is a short connection bar that is used to attach the power feeder lift that has room for a small width outfeed table.? Can anyone tell me what style of connection that is and whether Felder makes an extension table for this point? I see a couple in the catalogue, but can't tell which one would work for my application.

Alternatively, if some other company makes an outfeed table, or there are plans to make one, please let me know.

Using a power feeder on the shaper without an extension table provides very little room to catch the outfeed stock, plus I worry that longer stock will get pulled down by gravity at the leading edge and lift up the stock at the cutter head.

As always, your assistance and advice is really appreciated.

Warmly,

Bill White
SoCal (Orange County)






--
Dave & Marie Davies

318-219-7868
Re: Extension Table

 

John,

Where did you buy the Aigner product in Canada?

Thanks,
James

On Mon, Dec 5, 2016 at 9:49 PM, John jmkserv@... [felder-woodworking] <felder-woodworking@...> wrote:
?

I did the same basically 2 for the price of 1 Felder. I use them on the FB600, F700Z, and my AD951.?


John
JMK Services?




-------- Original message --------
From: "David Davies myfinishingtouch@... [felder-woodworking]" <felder-woodworking@yahoogroups.com>
Date: 2016-12-05 9:34 PM (GMT-05:00)
To: felder-woodworking <felder-woodworking@yahoogroups.com>
Subject: Re: [felder-woodworking] Extension Table

?

I ended up buying an Aigner extension fence from Carl at Martin.? I can't remember exactly ?now and their e-shop is down but I think it was about half the price of the Felder.

On Mon, Dec 5, 2016 at 7:36 PM, mac campshure mac512002@... [felder-woodworking] <felder-woodworking@yahoogroups.com> wrote:
?

I find it utterly amazing that you purchased a machine and an extension table at a minimum ?6x20"cast table was not part of your purchased.
?The table ends abruptly in less than a foot from spindle center line.
This is the responsibility of your sales person,,, period.
Like buying a saw with no blades what the hell. ?
mac...
?
martin/campshure/co/llc
mac campshure
7412 elmwood ave.
middleton, wi 53562-3106
608-332-2330 cell
airtightclamps@...

Designing and building for 46 years


From: "James Zhu james.zhu2@... [felder-woodworking]" <felder-woodworking@yahoogroups.com>
To: felder-woodworking@yahoogroups.com
Sent: Monday, December 5, 2016 7:18 PM
Subject: Re: [felder-woodworking] Extension Table

?
I observed the same thing, extension table is 100% needed on the KF 700. I need to order one too.

I think it is F-channel extension table.

I have the wide aluminum F-channel extension table, I use it on planer and bandsaw, but too wide, can't use it on the outfeed end of the KF.

James



On Mon, Dec 5, 2016 at 7:32 PM wildcoach@... [felder-woodworking] <felder-woodworking@yahoogroups.com> wrote:
?
Hi Everyone,

I have a current year KF700SP (delivered 2016) and want to put an extension table at the end of the shaper outfeed but I don't know what connection type that is.? There is a short connection bar that is used to attach the power feeder lift that has room for a small width outfeed table.? Can anyone tell me what style of connection that is and whether Felder makes an extension table for this point? I see a couple in the catalogue, but can't tell which one would work for my application.

Alternatively, if some other company makes an outfeed table, or there are plans to make one, please let me know.

Using a power feeder on the shaper without an extension table provides very little room to catch the outfeed stock, plus I worry that longer stock will get pulled down by gravity at the leading edge and lift up the stock at the cutter head.

As always, your assistance and advice is really appreciated.

Warmly,

Bill White
SoCal (Orange County)






--
Dave & Marie Davies

318-219-7868
Re: Extension Table

[email protected]
 

Simantech Inc carries the full range of Aigner (and I think they use Martin as a distributor :-)). Their website is up and running, has all the prices if you need to compare costs to the Felder unit
Re: Extension Table

 

I will use two at a time on occasion on my KF700 -- infeed and outfeed.? For the infeed I had to by the Aigner accessory for round bars to get it to mount.
Dave

On Mon, Dec 5, 2016 at 8:49 PM, John jmkserv@... [felder-woodworking] <felder-woodworking@...> wrote:
?

I did the same basically 2 for the price of 1 Felder. I use them on the FB600, F700Z, and my AD951.?


John
JMK Services?




-------- Original message --------
From: "David Davies myfinishingtouch@... [felder-woodworking]" <felder-woodworking@yahoogroups.com>
Date: 2016-12-05 9:34 PM (GMT-05:00)
To: felder-woodworking <felder-woodworking@yahoogroups.com>
Subject: Re: [felder-woodworking] Extension Table

?

I ended up buying an Aigner extension fence from Carl at Martin.? I can't remember exactly ?now and their e-shop is down but I think it was about half the price of the Felder.

On Mon, Dec 5, 2016 at 7:36 PM, mac campshure mac512002@... [felder-woodworking] <felder-woodworking@yahoogroups.com> wrote:
?

I find it utterly amazing that you purchased a machine and an extension table at a minimum ?6x20"cast table was not part of your purchased.
?The table ends abruptly in less than a foot from spindle center line.
This is the responsibility of your sales person,,, period.
Like buying a saw with no blades what the hell. ?
mac...
?
martin/campshure/co/llc
mac campshure
7412 elmwood ave.
middleton, wi 53562-3106
608-332-2330 cell
airtightclamps@...

Designing and building for 46 years


From: "James Zhu james.zhu2@... [felder-woodworking]" <felder-woodworking@yahoogroups.com>
To: felder-woodworking@yahoogroups.com
Sent: Monday, December 5, 2016 7:18 PM
Subject: Re: [felder-woodworking] Extension Table

?
I observed the same thing, extension table is 100% needed on the KF 700. I need to order one too.

I think it is F-channel extension table.

I have the wide aluminum F-channel extension table, I use it on planer and bandsaw, but too wide, can't use it on the outfeed end of the KF.

James



On Mon, Dec 5, 2016 at 7:32 PM wildcoach@... [felder-woodworking] <felder-woodworking@yahoogroups.com> wrote:
?
Hi Everyone,

I have a current year KF700SP (delivered 2016) and want to put an extension table at the end of the shaper outfeed but I don't know what connection type that is.? There is a short connection bar that is used to attach the power feeder lift that has room for a small width outfeed table.? Can anyone tell me what style of connection that is and whether Felder makes an extension table for this point? I see a couple in the catalogue, but can't tell which one would work for my application.

Alternatively, if some other company makes an outfeed table, or there are plans to make one, please let me know.

Using a power feeder on the shaper without an extension table provides very little room to catch the outfeed stock, plus I worry that longer stock will get pulled down by gravity at the leading edge and lift up the stock at the cutter head.

As always, your assistance and advice is really appreciated.

Warmly,

Bill White
SoCal (Orange County)






--
Dave & Marie Davies

318-219-7868




--
Dave & Marie Davies

318-219-7868
Re: Extension Table

 

Mac,

I completely agree with you.

I should have asked the sales guy to throw in the cast iron extension table. I was mislead and thought the aluminum extension table could be used on the KF700.

Besides, I could get it at 30% off accessory at the time of machine purchase.

Oh well, lesson learned. So anyone buys a Saw/shaper machine in the future, must get the narrow cast iron extension table.

James

On Mon, Dec 5, 2016 at 8:36 PM mac campshure mac512002@... [felder-woodworking] <felder-woodworking@...> wrote:

I find it utterly amazing that you purchased a machine and an extension table at a minimum ?6x20"cast table was not part of your purchased.
?The table ends abruptly in less than a foot from spindle center line.
This is the responsibility of your sales person,,, period.
Like buying a saw with no blades what the hell. ?
mac...
?
martin/campshure/co/llc
mac campshure
7412 elmwood ave.
middleton, wi 53562-3106
608-332-2330 cell
608-824-0023 fax
airtightclamps@...

Designing and building for 46 years


From: "James Zhu james.zhu2@... [felder-woodworking]" <felder-woodworking@...>
To: felder-woodworking@...
Sent: Monday, December 5, 2016 7:18 PM
Subject: Re: [felder-woodworking] Extension Table


?
I observed the same thing, extension table is 100% needed on the KF 700. I need to order one too.

I think it is F-channel extension table.

I have the wide aluminum F-channel extension table, I use it on planer and bandsaw, but too wide, can't use it on the outfeed end of the KF.

James



On Mon, Dec 5, 2016 at 7:32 PM wildcoach@... [felder-woodworking] <felder-woodworking@...> wrote:
?
Hi Everyone,

I have a current year KF700SP (delivered 2016) and want to put an extension table at the end of the shaper outfeed but I don't know what connection type that is.? There is a short connection bar that is used to attach the power feeder lift that has room for a small width outfeed table.? Can anyone tell me what style of connection that is and whether Felder makes an extension table for this point? I see a couple in the catalogue, but can't tell which one would work for my application.

Alternatively, if some other company makes an outfeed table, or there are plans to make one, please let me know.

Using a power feeder on the shaper without an extension table provides very little room to catch the outfeed stock, plus I worry that longer stock will get pulled down by gravity at the leading edge and lift up the stock at the cutter head.

As always, your assistance and advice is really appreciated.

Warmly,

Bill White
SoCal (Orange County)
Re: Extension Table

 

¿ªÔÆÌåÓý

I did the same basically 2 for the price of 1 Felder. I use them on the FB600, F700Z, and my AD951.?


John
JMK Services?




-------- Original message --------
From: "David Davies myfinishingtouch@... [felder-woodworking]" <felder-woodworking@...>
Date: 2016-12-05 9:34 PM (GMT-05:00)
To: felder-woodworking <felder-woodworking@...>
Subject: Re: [felder-woodworking] Extension Table

?

I ended up buying an Aigner extension fence from Carl at Martin.? I can't remember exactly ?now and their e-shop is down but I think it was about half the price of the Felder.

On Mon, Dec 5, 2016 at 7:36 PM, mac campshure mac512002@... [felder-woodworking] <felder-woodworking@...> wrote:
?

I find it utterly amazing that you purchased a machine and an extension table at a minimum ?6x20"cast table was not part of your purchased.
?The table ends abruptly in less than a foot from spindle center line.
This is the responsibility of your sales person,,, period.
Like buying a saw with no blades what the hell. ?
mac...
?
martin/campshure/co/llc
mac campshure
7412 elmwood ave.
middleton, wi 53562-3106
608-332-2330 cell
airtightclamps@...

Designing and building for 46 years


From: "James Zhu james.zhu2@... [felder-woodworking]" <felder-woodworking@yahoogroups.com>
To: felder-woodworking@yahoogroups.com
Sent: Monday, December 5, 2016 7:18 PM
Subject: Re: [felder-woodworking] Extension Table

?
I observed the same thing, extension table is 100% needed on the KF 700. I need to order one too.

I think it is F-channel extension table.

I have the wide aluminum F-channel extension table, I use it on planer and bandsaw, but too wide, can't use it on the outfeed end of the KF.

James



On Mon, Dec 5, 2016 at 7:32 PM wildcoach@... [felder-woodworking] <felder-woodworking@yahoogroups.com> wrote:
?
Hi Everyone,

I have a current year KF700SP (delivered 2016) and want to put an extension table at the end of the shaper outfeed but I don't know what connection type that is.? There is a short connection bar that is used to attach the power feeder lift that has room for a small width outfeed table.? Can anyone tell me what style of connection that is and whether Felder makes an extension table for this point? I see a couple in the catalogue, but can't tell which one would work for my application.

Alternatively, if some other company makes an outfeed table, or there are plans to make one, please let me know.

Using a power feeder on the shaper without an extension table provides very little room to catch the outfeed stock, plus I worry that longer stock will get pulled down by gravity at the leading edge and lift up the stock at the cutter head.

As always, your assistance and advice is really appreciated.

Warmly,

Bill White
SoCal (Orange County)






--
Dave & Marie Davies

318-219-7868
Re: Extension Table

 

I ended up buying an Aigner extension fence from Carl at Martin.? I can't remember exactly ?now and their e-shop is down but I think it was about half the price of the Felder.

On Mon, Dec 5, 2016 at 7:36 PM, mac campshure mac512002@... [felder-woodworking] <felder-woodworking@...> wrote:

?

I find it utterly amazing that you purchased a machine and an extension table at a minimum ?6x20"cast table was not part of your purchased.
?The table ends abruptly in less than a foot from spindle center line.
This is the responsibility of your sales person,,, period.
Like buying a saw with no blades what the hell. ?
mac...
?
martin/campshure/co/llc
mac campshure
7412 elmwood ave.
middleton, wi 53562-3106
608-332-2330 cell
airtightclamps@...

Designing and building for 46 years


From: "James Zhu james.zhu2@... [felder-woodworking]" <felder-woodworking@yahoogroups.com>
To: felder-woodworking@yahoogroups.com
Sent: Monday, December 5, 2016 7:18 PM
Subject: Re: [felder-woodworking] Extension Table

?
I observed the same thing, extension table is 100% needed on the KF 700. I need to order one too.

I think it is F-channel extension table.

I have the wide aluminum F-channel extension table, I use it on planer and bandsaw, but too wide, can't use it on the outfeed end of the KF.

James



On Mon, Dec 5, 2016 at 7:32 PM wildcoach@... [felder-woodworking] <felder-woodworking@yahoogroups.com> wrote:
?
Hi Everyone,

I have a current year KF700SP (delivered 2016) and want to put an extension table at the end of the shaper outfeed but I don't know what connection type that is.? There is a short connection bar that is used to attach the power feeder lift that has room for a small width outfeed table.? Can anyone tell me what style of connection that is and whether Felder makes an extension table for this point? I see a couple in the catalogue, but can't tell which one would work for my application.

Alternatively, if some other company makes an outfeed table, or there are plans to make one, please let me know.

Using a power feeder on the shaper without an extension table provides very little room to catch the outfeed stock, plus I worry that longer stock will get pulled down by gravity at the leading edge and lift up the stock at the cutter head.

As always, your assistance and advice is really appreciated.

Warmly,

Bill White
SoCal (Orange County)






--
Dave & Marie Davies

318-219-7868
Re: Extension Table

 

I find it utterly amazing that you purchased a machine and an extension table at a minimum ?6x20"cast table was not part of your purchased.
?The table ends abruptly in less than a foot from spindle center line.
This is the responsibility of your sales person,,, period.
Like buying a saw with no blades what the hell. ?
mac...
?
martin/campshure/co/llc
mac campshure
7412 elmwood ave.
middleton, wi 53562-3106
608-332-2330 cell
608-824-0023 fax
Designing and building for 46 years


From: "James Zhu james.zhu2@... [felder-woodworking]" To: felder-woodworking@...
Sent: Monday, December 5, 2016 7:18 PM
Subject: Re: [felder-woodworking] Extension Table

?
I observed the same thing, extension table is 100% needed on the KF 700. I need to order one too.

I think it is F-channel extension table.

I have the wide aluminum F-channel extension table, I use it on planer and bandsaw, but too wide, can't use it on the outfeed end of the KF.

James



On Mon, Dec 5, 2016 at 7:32 PM wildcoach@... [felder-woodworking] <felder-woodworking@...> wrote:
?
Hi Everyone,

I have a current year KF700SP (delivered 2016) and want to put an extension table at the end of the shaper outfeed but I don't know what connection type that is.? There is a short connection bar that is used to attach the power feeder lift that has room for a small width outfeed table.? Can anyone tell me what style of connection that is and whether Felder makes an extension table for this point? I see a couple in the catalogue, but can't tell which one would work for my application.

Alternatively, if some other company makes an outfeed table, or there are plans to make one, please let me know.

Using a power feeder on the shaper without an extension table provides very little room to catch the outfeed stock, plus I worry that longer stock will get pulled down by gravity at the leading edge and lift up the stock at the cutter head.

As always, your assistance and advice is really appreciated.

Warmly,

Bill White
SoCal (Orange County)
56461 - 56480 of 141175