Hi Eduard,
The link above shows the seal for the oil chamber for Vario4. My manual shows many other PFs but not your model. So look for a similar seal.
Many posters have recently posted a leak from this seal due to how the PF was stored for a relatively long time. What happens is that the seal drys out and then when PF is in correct orientation it fails to seal.
My manual calls out (see pic in the linked post) some german oil but also says SAE30 can be used.
Hopefully this helps you going.
Imran?
toggle quoted message
Show quoted text
On May 14, 2021, at 7:24 PM, Eduard Nemirovsky <eduard.nemirovsky@...> wrote: ?Hi all,
I was moving my shop for a last 4-5 month and during all this time Felder feeder S-308 was lying on it side, on the pallet. Now after putting it on machine, I see oil dripping from it on the table. Feeder is working, no creasy or unusual sound during powered, but this dripping oil really bothered me. Where it is leaking from, how to stop it( yea, I know, wait for all oil to leaking out ::), and probably I need to replace it? Do I need to buy oil from Felder, with all creasiness with shipping, not the best option? What kind of oil should I use?
Thank you and have a nice weekend.
Ed.
|
Re: Japanese Pull Saw Recommendation
I just noticed in the shop today that I have a 372, like Taylor said it is a nice saw…
toggle quoted message
Show quoted text
On May 13, 2021, at 7:06 PM, imranindiana via groups.io <imranindiana@...> wrote:
? Thanks Roger. I guess I lucked out, as the Dozuki has a rigid back.
Imran
On May 13, 2021, at 5:09 PM, Roger S <rsinden@...> wrote:
? Imran
Don’t waste your money on the set. ?I went to Japan and bought a load of their saws…tried using them and just didn't get on with any without a rigid back.
But there you’re talking…just bought my third. ?It’s my go-to saw for small stuff.?
?Ice Bear Japanese Ikedame Dovetail Saw
Careful…the teeth are brittle.
Roger
I am more a traditional saw guy for any important cuts, but i do like this flush cut saw and i have had many over the years as they are basically throw aways.
Gyokucho Razorsaw Flush Cutting Single Edge Saw 100mm No. 1150?
And this one is very handy as well
|
Hi all,
I was moving my shop for a last 4-5 month and during all this time Felder feeder S-308 was lying on it side, on the pallet. Now after putting it on machine, I see oil dripping from it on the table. Feeder is working, no creasy or unusual sound during powered, but this dripping oil really bothered me. Where it is leaking from, how to stop it( yea, I know, wait for all oil to leaking out ::), and probably I need to replace it? Do I need to buy oil from Felder, with all creasiness with shipping, not the best option? What kind of oil should I use?
Thank you and have a nice weekend.
Ed.
|
Re: Japanese Pull Saw Recommendation
You can use a non flush cut saw but they will gouge the wood surface due to their offset teeth. The flush cut saw has no offset and does not damage the surface much if at all.? Taylor Donsker www.tdonsker.com 818.424.9046
toggle quoted message
Show quoted text
On May 14, 2021, at 6:17 AM, imranindiana via groups.io <imranindiana@...> wrote:
? Thanks again for all the feedback. I was not looking for a flush cut saw but if the rip/xcut also worked as one that would have been a bonus. Anyhow, now I have details on the flush cut as well ?
Imran
On May 13, 2021, at 11:49 PM, Cliff Rohrabacher, Esq. <rohrabacher@...> wrote:
?
And available at walmart
Hi Imran,
I second Taylor's recommendation of the Gyokucho's?
Here's a video by David Barron in which he does a run down of
various models and their features and applications. I even hit a
hidden nail with mine doing some restoration work and it's still
quite sharp. I think I got the 307. I ordered mine off eBay and
purchased a spare blade at the same time.?
Cheers
Michael
|
Re: Japanese Pull Saw Recommendation
Thanks again for all the feedback. I was not looking for a flush cut saw but if the rip/xcut also worked as one that would have been a bonus. Anyhow, now I have details on the flush cut as well ?
Imran
toggle quoted message
Show quoted text
On May 13, 2021, at 11:49 PM, Cliff Rohrabacher, Esq. <rohrabacher@...> wrote: ?
And available at walmart
Hi Imran,
I second Taylor's recommendation of the Gyokucho's?
Here's a video by David Barron in which he does a run down of
various models and their features and applications. I even hit a
hidden nail with mine doing some restoration work and it's still
quite sharp. I think I got the 307. I ordered mine off eBay and
purchased a spare blade at the same time.?
Cheers
Michael
|
Re: Will Felder ever make a spindle moulder like this?
Congrats Albert. What a beautiful machine. When you ordered, I was able to find a video (or maybe you had shared one) that showed how the sliding table on the side worked. That was fun to watch. Anyhow, I found a brochure and spotted the power feeder stand. I have not seen one like this with counters before.
Imran
toggle quoted message
Show quoted text
On May 13, 2021, at 8:40 PM, Albert Lee <timbershelf@...> wrote: ? [Edited Message Follows]
My new spindle moulder was delivered around early May, I ordered it in July 2020, arrived at our shore around Feb 2021. No its not a Felder its a SCM, I like SCM and Felder but preferred SCM, I may have bought Felder but unfortunately Felder does not offer a spindle moulder with sliding table on its side.? I wondered will Felder ever offer something similar? I know even a smaller Czech company Houfek offers spindle moulder in this configuration.? The user manual says I need 7.6m x 6.6m work space for it, with the machine in the middle of it - my workshop is only 9m x 6m. it currently lives in an area of 2.1m x 5m
<1.jpg> <2.jpg> <3.jpg> <4.jpg> <5.jpg> <6.jpg> <8.jpg> <9.jpg> <10.jpg>
|
Re: Japanese Pull Saw Recommendation
toggle quoted message
Show quoted text
Hi Imran,
I second Taylor's recommendation of the Gyokucho's?
Here's a video by David Barron in which he does a run down of
various models and their features and applications. I even hit a
hidden nail with mine doing some restoration work and it's still
quite sharp. I think I got the 307. I ordered mine off eBay and
purchased a spare blade at the same time.?
Cheers
Michael
|
Re: Will Felder ever make a spindle moulder like this?
"Will Felder ever make a spindle moulder like this?"
Well that question is moot for you.
Congrats? on the new toy
|
Re: Will Felder ever make a spindle moulder like this?
While I personally agree with the sliding table configuration you specify Albert, I would guess Felder's retort would be the ability to add outriggers? and crosscut fences to their sliding table system. I thought the new Profil92 had more options and features in that area, though I could be mistaken.? One thing I was surprised at the sliding end table? layout is how much more workspace is necessary to navigate that feature, especially with long boards, for end-cuts. But I do prefer the sliding end table.
Wow, Albert! you're going to set a world record for the amount of machinery per m2 for sure! But I can still see some bare concrete..........
That looks like an incredible machine. I do like the sound of that sliding table configuration.?
Cheers
Michael?
|
Re: Japanese Pull Saw Recommendation
Here is my flush cut saw:?
I previously ordered a different, ultra thin flush cut saw and bent it on the first damn use. I am pretty familiar with them and hate the producer for making such a ridiculously thin body that literally became worthless after 6 pulls. Thin cuts fast but also allows movement with no backing... Taylor Donsker www.tdonsker.com 818.424.9046
toggle quoted message
Show quoted text
On May 13, 2021, at 6:33 PM, michael.kit.ooi@... wrote:
?Hi Imran,
I second Taylor's recommendation of the Gyokucho's?
Here's a video by David Barron in which he does a run down of various models and their features and applications. I even hit a hidden nail with mine doing some restoration work and it's still quite sharp. I think I got the 307. I ordered mine off eBay and purchased a spare blade at the same time.?
Cheers
Michael
|
Re: Japanese Pull Saw Recommendation
Hi Imran,
I second Taylor's recommendation of the Gyokucho's?
Here's a video by David Barron in which he does a run down of various models and their features and applications. I even hit a hidden nail with mine doing some restoration work and it's still quite sharp. I think I got the 372. I ordered mine off eBay and purchased a spare blade at the same time.?
Cheers
Michael
|
Re: Will Felder ever make a spindle moulder like this?
Wow, Albert! you're going to set a world record for the amount of machinery per m2 for sure! But I can still see some bare concrete..........
That looks like an incredible machine. I do like the sound of that sliding table configuration.?
Cheers
Michael?
|
Will Felder ever make a spindle moulder like this?
My new spindle moulder was delivered around early May, I ordered it in July 2020, arrived at our shore around Feb 2021.
No its not a Felder its a SCM, I like SCM and Felder but preferred SCM, I may have bought Felder but unfortunately Felder does not offer a spindle moulder with sliding table on its side.?
I wondered will Felder ever offer something similar? I know even a smaller Czech company Houfek offers spindle moulder in this configuration.?
The user manual says I need 7.6m x 6.6m work space for it, with the machine in the middle of it - my workshop is only 9m x 6m. it currently lives in an area of 2.1m x 5m
|
Re: Finger Pulls on Drawer fronts
Bob, I work with Eucalypts all the time. Just treat what you have as a hard wood. You do not specify the wood type - there are a million varieties. Most of the ones I have worked are unlike Maple, which burns if you point a router at it. Just use a slower speed to be safe.
Regards from Perth
Derek
|
Re: Japanese Pull Saw Recommendation
None of those saws in that set (from LV) are designed fir flush cutting. A flush cutting saw will have set on one side of the teeth only, and there would not be a back to the saw plate so as to make the plate/blade more flexible.?
This is a particularly good flush cut saw from LN. It cuts on the pull ...
The smallest saw in the LV set is great for dovetails and fine detail cuts. Incidentally, these saws look to be made by Z-saw, which is a very good company for inexpensive, mass-produced saws. I have a couple.
Japanese saws for tenons? Get a Ryoba. This is a double sided saw, one side fir crosscutting and the other for rip. From LV ...
Regards from Perth
Derek
|
Re: Japanese Pull Saw Recommendation
Thanks Roger. I guess I lucked out, as the Dozuki has a rigid back.
Imran
toggle quoted message
Show quoted text
On May 13, 2021, at 5:09 PM, Roger S <rsinden@...> wrote: ? Imran
Don’t waste your money on the set. ?I went to Japan and bought a load of their saws…tried using them and just didn't get on with any without a rigid back.
But there you’re talking…just bought my third. ?It’s my go-to saw for small stuff.?
?Ice Bear Japanese Ikedame Dovetail Saw
Careful…the teeth are brittle.
Roger
I am more a traditional saw guy for any important cuts, but i do like this flush cut saw and i have had many over the years as they are basically throw aways.
Gyokucho Razorsaw Flush Cutting Single Edge Saw 100mm No. 1150?
And this one is very handy as well
|
Re: Japanese Pull Saw Recommendation
Imran
Don’t waste your money on the set. ?I went to Japan and bought a load of their saws…tried using them and just didn't get on with any without a rigid back.
But there you’re talking…just bought my third. ?It’s my go-to saw for small stuff.?
?Ice Bear Japanese Ikedame Dovetail Saw
Careful…the teeth are brittle.
toggle quoted message
Show quoted text
I am more a traditional saw guy for any important cuts, but i do like this flush cut saw and i have had many over the years as they are basically throw aways.
Gyokucho Razorsaw Flush Cutting Single Edge Saw 100mm No. 1150?
And this one is very handy as well
|
Re: Japanese Pull Saw Recommendation
Thanks everyone. Even though I was not looking for a dovetail saw the endorsements for Dozuki, especially the all out one from Taylor, LOL, convinced me to give Gyokucho 372?a try.
Looking forward to receiving it next week.
Imran
toggle quoted message
Show quoted text
On May 13, 2021, at 3:38 PM, t d <tdonsker@...> wrote: ? The gyokucho 372 is the finest saw ever made in my opinion. Its kerf is so fine it cuts anything with ease. The rigid backing limits its application but i reach for it for anything under 2” depth of cut. I dont like ryobas except for cutting nails. That was a joke. But really i do not like them as they are like a no. 5 jack plane. You may as well buy a saw at home depot.?
Anyways katabas are the big brother of the 372 (crosscut) and i bought a hand made version by mitsukawa. To be honest the cost doesnt really make sense but tomohito iida has some great deals on other hand made japanese goods. ?He is really friendly and knowledgeable and has contacts with most of the remaining tool makers.? In general i do not favor the ripping saws from japan because the teeth are so large and aggressive they tear out a lot and just are not a pleasurable sawing experience. The kataba is a happy medium especially in the larger size as it has big but less offset teeth than a similar sized ryoba would. ?You should also try and specify the type of wood you are cutting as softwoods and hardwoods require different setting and spacing of the teeth.?
Taylor Donsker www.tdonsker.com 818.424.9046 On May 13, 2021, at 10:31 AM, Mark Kessler <mkessler10@...> wrote:
? I am more a traditional saw guy for any important cuts, but i do like this flush cut saw and i have had many over the years as they are basically throw aways.
Gyokucho Razorsaw Flush Cutting Single Edge Saw 100mm No. 1150?
And this one is very handy as well
|
Re: Japanese Pull Saw Recommendation
The gyokucho 372 is the finest saw ever made in my opinion. Its kerf is so fine it cuts anything with ease. The rigid backing limits its application but i reach for it for anything under 2” depth of cut. I dont like ryobas except for cutting nails. That was a joke. But really i do not like them as they are like a no. 5 jack plane. You may as well buy a saw at home depot.?
Anyways katabas are the big brother of the 372 (crosscut) and i bought a hand made version by mitsukawa. To be honest the cost doesnt really make sense but tomohito iida has some great deals on other hand made japanese goods. ?He is really friendly and knowledgeable and has contacts with most of the remaining tool makers.? In general i do not favor the ripping saws from japan because the teeth are so large and aggressive they tear out a lot and just are not a pleasurable sawing experience. The kataba is a happy medium especially in the larger size as it has big but less offset teeth than a similar sized ryoba would. ?You should also try and specify the type of wood you are cutting as softwoods and hardwoods require different setting and spacing of the teeth.?
Taylor Donsker www.tdonsker.com 818.424.9046
toggle quoted message
Show quoted text
On May 13, 2021, at 10:31 AM, Mark Kessler <mkessler10@...> wrote:
? I am more a traditional saw guy for any important cuts, but i do like this flush cut saw and i have had many over the years as they are basically throw aways.
Gyokucho Razorsaw Flush Cutting Single Edge Saw 100mm No. 1150?
And this one is very handy as well
|
Re: Japanese Pull Saw Recommendation
I am more a traditional saw guy for any important cuts, but i do like this flush cut saw and i have had many over the years as they are basically throw aways.
Gyokucho Razorsaw Flush Cutting Single Edge Saw 100mm No. 1150?
And this one is very handy as well
|
imran
Albert Lee
