|
Re: Wire and breaker size for 7.5HP 3 Phase Felder Shaper - NEC Code compliant
开云体育Been using this one since 73 very handy might be able to get them free from Square D probably doubt it?martin/campshure/co/llc Designing and building for 50 years On May 3, 2025, at 7:16?AM, imran via groups.io <imranwoodshop@...> wrote:
|
|
Re: Wire and breaker size for 7.5HP 3 Phase Felder Shaper - NEC Code compliant
开云体育Here are the currents of various Felder 3 ph motors from my machines as a reference but wiring should be done based upon the motor rating.My 5.5KW (7.4HP) 3 ph machine label says 24A. So I have it on a 30A circuit breaker. It may run on C16 (16A) but you should consult your electrician as it likely will not meet the local code and in case of a fire the insurance may not pay up due to code violation. Imran Malik IAM Wood Creations On May 3, 2025, at 3:06?AM, Colum via groups.io <colum@...> wrote:
? Hi all, Just reading through on this chat, does anyone have a go to chart for sizing cables and breakers for 3 phase equipment. I am being told by Felder c16 breakers are fine in my shop, with an kf700s saw/spindle, ad 741 planer, fb610 bandsaw and rl160 extractor, each on c16, and All this rolls up to c40 main breaker. Heating/AC, small power separate.
seems ok? ?
thanks
?
colum
|
|
Re: Wire and breaker size for 7.5HP 3 Phase Felder Shaper - NEC Code compliant
Hi all, Just reading through on this chat, does anyone have a go to chart for sizing cables and breakers for 3 phase equipment. I am being told by Felder c16 breakers are fine in my shop, with an kf700s saw/spindle, ad 741 planer, fb610 bandsaw and rl160 extractor, each on c16, and All this rolls up to c40 main breaker. Heating/AC, small power separate.
seems ok? ?
thanks
?
colum |
|
Re: K700 LCD issue
开云体育Hi Joe,It is hard to tell from pic if you caught it during refresh. I helped a member who had a bad display on planer. I checked voltages, Crystal, clock and looked for obvious bad parts but in the end there was nothing I could do to fix it. I would call felder and get a replacement. His machine was much older and he was still able to get a replacement. I don’t think it was overly expensive. If it was my machine I would check incoming voltage to the display board to be sure that it is in check. I don’t not think the encoder input being bad would result in an erratic segment display but those areas can be cleaned. HTH, Imran Malik IAM Wood Creations On May 2, 2025, at 12:27?PM, joe_tedesco via groups.io <joe_tedesco@...> wrote:
? Has anyone come across this issue? ?I'm out of warranty, so wondering if this is an easy fix, like possibly a cable/connection issue?
?
Thanks
Joe
?
<IMG_2088.jpeg> |
|
Re: Nova Viking Performance and Experience
I would like to commend Grizzly to have done the right thing and pay for the extended warranty as their customer service had told me. This is not the first time Grizzly has impressed me. They were equally good on my 12” disc sander. They sent replacement disc and table as they were not flat.
?
Imran |
|
Re: Aigner Sawboy
开云体育Netanel,Well that is how it is intended to be used.?Aigner products are usually well thought out.?Download the Aigner catalog. It has a lot of pictures showing how to use the product. I would just check the fence profile to verify it is compatible with wherever the hole/tap/insert (as David mentioned) needs to be. Imran Malik IAM Wood Creations On May 2, 2025, at 12:09?AM, netanel.belgazal via groups.io <netanel.belgazal@...> wrote:
? Imran,
?
I was just thinking about why I wouldn’t just drill and tap the rip fence.
Besides having a hole in the fence, that is perfect solution.
|
|
Re: Aigner Sawboy
开云体育Drill the fence extrusion and install a press fit threaded insert like this (that matches the bolt) :? https://www.mcmaster.com/97191A129 David Best - via mobile phone? On May 1, 2025, at 9:09?PM, netanel.belgazal via groups.io <netanel.belgazal@...> wrote:
|
|
Re: Aigner Sawboy
开云体育Netanel, The version you have connects to the rip fence via the bolt. If fence is thick enough it can be tapped, if not then the nuts secures it with a clearance hole in the fence. If the hole height is compatible with the rip fence it should work. Maybe you know this and just don’t prefer this attachment method. HTH, Imran Malik IAM Wood Creations On May 1, 2025, at 11:47?PM, netanel.belgazal via groups.io <netanel.belgazal@...> wrote:
? If anyone interested.
?
I bought a Sawboy from S&S and apparently there are more than one version of it.
mine came with a T nut on the back.?
The version that Felder sales is the one with two Kipp lever that attached to the rip fence from above.
This is something I can’t do with the version I have.
I need to see if Aigner can sale only the back fence.
?
<photo-3.jpg> |
|
Re: Aigner Sawboy
If anyone interested.
?
I bought a Sawboy from S&S and apparently there are more than one version of it.
mine came with a T nut on the back.?
The version that Felder sales is the one with two Kipp lever that attached to the rip fence from above.
This is something I can’t do with the version I have.
I need to see if Aigner can sale only the back fence.
?
|
|
For Sale - rip fence kit for K940s
Gentleman, I have an extra rip fence for a 2019 K940s that I ended up with and am not using.? It was working fine but instead of modifying it to add the digital read out I purchased a new one.? ?I believe that the correct part number for this is 431008-029+1D and it is about $1300 new.? ?I am asking 700 + shipping.? ?Please PM or email me if you are interested.??
?
I am in the Charlotte NC area if you are on the east coast -
--
Michael Marsico |
imran
Colum
David P. Best
