¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
  1. Felderownersgroup
  2. Messages
Expanded Topics Messages Polls
Date
Re: Cf741s-fine cut blade leaving ripples in Pear.

 

¿ªÔÆÌåÓý

I assume these blades used to cut fine and you have them both sharpened, so my first thought would be to try another blade and see what happens.

Moving on, you are xcutting material clamped to the slider and getting ripples on the endgrain. A picture would be very helpful, so I am assuming that you are not getting blade arc impressions which you could get with improper toe out. This is easy to tell as the arc of leading edge of the blade is opposite to the trailing edge, concave vs convex.

Are you making a trim cut where only the left side of blade is in the wood? If so try to cut where you have couple of inches of cutoff and examine both pieces.

You should check the splitter is adjusted properly. You could also remove it and make a test cut with clamped material. This will eliminate the splitter as a contributor.

I am no expert but I try to remove as many contributors as possible. For grins, I would also change material type or at least try another piece of wood.

Imran Malik
IAM Wood Creations

On Jan 6, 2025, at 7:09?AM, Colum via groups.io <colum@...> wrote:

?
Hi
?
have a resharpened Leitz and Felder 96 tooth ATB blades on the saw and it¡¯s leaving some ripples on the end grain cuts.
?
Arbor is clean, no dust particles between it and blades and blades sound normal to the ear. No describable wobble.
?
its running at 25mm above the bed with good clearance on the blades gullets.

any thoughts suggestions.
?
stock is also clamped so no movement laterally on the slider.
?
many thanks in advance for your replies.
?
colum o Donovan?
dubai and chamonix
?
Re: Cf741s-fine cut blade leaving ripples in Pear.

 

¿ªÔÆÌåÓý

I would try running the blade at full height so the cutting action is down instead of horizontal?
Bill Belanger?


On Jan 6, 2025, at 05:09, Colum via groups.io <colum@...> wrote:

?
Hi
?
have a resharpened Leitz and Felder 96 tooth ATB blades on the saw and it¡¯s leaving some ripples on the end grain cuts.
?
Arbor is clean, no dust particles between it and blades and blades sound normal to the ear. No describable wobble.
?
its running at 25mm above the bed with good clearance on the blades gullets.

any thoughts suggestions.
?
stock is also clamped so no movement laterally on the slider.
?
many thanks in advance for your replies.
?
colum o Donovan?
dubai and chamonix
?
Cf741s-fine cut blade leaving ripples in Pear.

 

Hi
?
have a resharpened Leitz and Felder 96 tooth ATB blades on the saw and it¡¯s leaving some ripples on the end grain cuts.
?
Arbor is clean, no dust particles between it and blades and blades sound normal to the ear. No describable wobble.
?
its running at 25mm above the bed with good clearance on the blades gullets.

any thoughts suggestions.
?
stock is also clamped so no movement laterally on the slider.
?
many thanks in advance for your replies.
?
colum o Donovan?
dubai and chamonix
?
Re: WTB: F coupling rails 600 or 300 mm

 

Timothy, I have a couple extra Felder table extensions (1000mmx150mm - part No. 400-104) that come with the 300mm F-coupling.??
?
If interested you can message me directly.
?
Troy
503-869-5668
Re: Drawer slide recommendations

 

I appreciate the suggestions, fellows. I will give the KV slides a try. Maybe not the 500-pound slides at $140 per pair, but the model 8500 look interesting.
?
Thanks to all of you for your suggestions.
--
John Hinman
Boise ID
Kappa 450X and A941
Re: Drawer slide recommendations

 

¿ªÔÆÌåÓý

I use KV 8908 as well. ?My supplier is??- they have a branch near you in Boise and worth setting up an account if you don¡¯t already have one. ?They have good pricing and will ship to the local branch for pick up free of charge if they¡¯re not already in stock. ?

David Best - via mobile phone?

On Jan 5, 2025, at 10:14?AM, John Hinman via groups.io <jhinman1911@...> wrote:

?
I am putting together another bank of drawers for my shop, and am looking for recommendations for drawer slides. Boxes are 35¡± wide, and will carry both heavy and light loads.
?
I¡¯m the past I have used Accuride side mounts, but the last I bought was disappointing. I like the rigidity of side mounts, and I do not care that the hardware is visible. I just want drawers that open and close smoothly and quietly.
?
Blum is a good brand, but apparently they do not make side mounts.
?
There are plenty of less expensive imports - are any these any good?
--
John Hinman
Boise ID
Kappa 450X and A941
Re: Inset drawer lighting

 

You guys have confirmed my thought on them. Seem difficult to implement and not much value. Thank you.?
--
Stan Blaszczyk
Causal Maker of Stuff
Cincinnati, OH
Re: Drawer slide recommendations

 

¿ªÔÆÌåÓý

I used KV8400 in shop slides. Drawers contain heavy tooling and multiple shaper spindles. No issues.

Imran Malik
IAM Wood Creations

On Jan 5, 2025, at 3:30?PM, Jarrett Maxwell via groups.io <j.a.max7@...> wrote:

?
I have Fulterer brand in my shop and they work great. I think Fulterer is a German company but the slides are made in Taiwan. They've been a good balance between cost and performance. I have a mix of 100lb and 200lb rated ball bearing slides with no issues.?

Jarrett

On Sun, Jan 5, 2025, 1:56?PM Andy via <andy.raynor08=[email protected]> wrote:
KV 8908s with lock in/outs.? Load rating 200-500 lbs. great for shops and for pack outs.?

On Sun, Jan 5, 2025 at 2:48?PM Brian Lamb via <blamb11=[email protected]> wrote:
I agree with KV, they seem smoother than the Accuride and have worked well for me.

Brian Lamb


On Sunday, January 5, 2025 at 12:43:31 PM MST, Wade Dees via <wjdsignature=[email protected]> wrote:


John,

I used KV heavy duty slides in my shop. ?13 plus years and still going strong. ?

Thx,

Wade



On Jan 5, 2025, at 10:14?AM, John Hinman via <jhinman1911=[email protected]> wrote:

?
I am putting together another bank of drawers for my shop, and am looking for recommendations for drawer slides. Boxes are 35¡± wide, and will carry both heavy and light loads.
?
I¡¯m the past I have used Accuride side mounts, but the last I bought was disappointing. I like the rigidity of side mounts, and I do not care that the hardware is visible. I just want drawers that open and close smoothly and quietly.
?
Blum is a good brand, but apparently they do not make side mounts.
?
There are plenty of less expensive imports - are any these any good?
--
John Hinman
Boise ID
Kappa 450X and A941
Re: Drawer slide recommendations

 

I have Fulterer brand in my shop and they work great. I think Fulterer is a German company but the slides are made in Taiwan. They've been a good balance between cost and performance. I have a mix of 100lb and 200lb rated ball bearing slides with no issues.?

Jarrett

On Sun, Jan 5, 2025, 1:56?PM Andy via <andy.raynor08=[email protected]> wrote:
KV 8908s with lock in/outs.? Load rating 200-500 lbs. great for shops and for pack outs.?

On Sun, Jan 5, 2025 at 2:48?PM Brian Lamb via <blamb11=[email protected]> wrote:
I agree with KV, they seem smoother than the Accuride and have worked well for me.

Brian Lamb


On Sunday, January 5, 2025 at 12:43:31 PM MST, Wade Dees via <wjdsignature=[email protected]> wrote:


John,

I used KV heavy duty slides in my shop. ?13 plus years and still going strong. ?

Thx,

Wade



On Jan 5, 2025, at 10:14?AM, John Hinman via <jhinman1911=[email protected]> wrote:

?
I am putting together another bank of drawers for my shop, and am looking for recommendations for drawer slides. Boxes are 35¡± wide, and will carry both heavy and light loads.
?
I¡¯m the past I have used Accuride side mounts, but the last I bought was disappointing. I like the rigidity of side mounts, and I do not care that the hardware is visible. I just want drawers that open and close smoothly and quietly.
?
Blum is a good brand, but apparently they do not make side mounts.
?
There are plenty of less expensive imports - are any these any good?
--
John Hinman
Boise ID
Kappa 450X and A941
Re: Drawer slide recommendations

 

KV 8908s with lock in/outs.? Load rating 200-500 lbs. great for shops and for pack outs.?

On Sun, Jan 5, 2025 at 2:48?PM Brian Lamb via <blamb11=[email protected]> wrote:
I agree with KV, they seem smoother than the Accuride and have worked well for me.

Brian Lamb


On Sunday, January 5, 2025 at 12:43:31 PM MST, Wade Dees via <wjdsignature=[email protected]> wrote:


John,

I used KV heavy duty slides in my shop. ?13 plus years and still going strong. ?

Thx,

Wade



On Jan 5, 2025, at 10:14?AM, John Hinman via <jhinman1911=[email protected]> wrote:

?
I am putting together another bank of drawers for my shop, and am looking for recommendations for drawer slides. Boxes are 35¡± wide, and will carry both heavy and light loads.
?
I¡¯m the past I have used Accuride side mounts, but the last I bought was disappointing. I like the rigidity of side mounts, and I do not care that the hardware is visible. I just want drawers that open and close smoothly and quietly.
?
Blum is a good brand, but apparently they do not make side mounts.
?
There are plenty of less expensive imports - are any these any good?
--
John Hinman
Boise ID
Kappa 450X and A941
Re: Some questions on the Overhead Guard

 

Rock On Mac!? Thank you for sharing that gem
Brian K O'Brien?

On Sat, Jan 4, 2025, 1:51?PM mac campshure via <mac512002=[email protected]> wrote:

Sexton have 3 of these

martin/campshure/co/llc
mac campshure
7412 elmwood ave.
middleton, wi 53562-3106
608-332-2330?cell

airtightclamps@...


Designing and building for 50 years


On Nov 7, 2024, at 7:49?PM, Jacques Gagnon via <jacques.gagnon309=[email protected]> wrote:

?
Rusty,
?
Very nice job Sir!
?
Just out of curiosity, how much time do you think you spent on design and fabrication?
?
Regards,
?
Jacques

472003274_1135312031576908_7002043213948230447_n.jpg
472003274_1135312031576908_7002043213948230447_n.jpg

Re: Drawer slide recommendations

 

I agree with KV, they seem smoother than the Accuride and have worked well for me.

Brian Lamb
blamb11@...
lambtoolworks.com


On Sunday, January 5, 2025 at 12:43:31 PM MST, Wade Dees via groups.io <wjdsignature@...> wrote:


John,

I used KV heavy duty slides in my shop. ?13 plus years and still going strong. ?

Thx,

Wade



On Jan 5, 2025, at 10:14?AM, John Hinman via groups.io <jhinman1911@...> wrote:

?
I am putting together another bank of drawers for my shop, and am looking for recommendations for drawer slides. Boxes are 35¡± wide, and will carry both heavy and light loads.
?
I¡¯m the past I have used Accuride side mounts, but the last I bought was disappointing. I like the rigidity of side mounts, and I do not care that the hardware is visible. I just want drawers that open and close smoothly and quietly.
?
Blum is a good brand, but apparently they do not make side mounts.
?
There are plenty of less expensive imports - are any these any good?
--
John Hinman
Boise ID
Kappa 450X and A941

Re: Drawer slide recommendations

 

¿ªÔÆÌåÓý

John,

I used KV heavy duty slides in my shop. ?13 plus years and still going strong. ?

Thx,

Wade



On Jan 5, 2025, at 10:14?AM, John Hinman via groups.io <jhinman1911@...> wrote:

?
I am putting together another bank of drawers for my shop, and am looking for recommendations for drawer slides. Boxes are 35¡± wide, and will carry both heavy and light loads.
?
I¡¯m the past I have used Accuride side mounts, but the last I bought was disappointing. I like the rigidity of side mounts, and I do not care that the hardware is visible. I just want drawers that open and close smoothly and quietly.
?
Blum is a good brand, but apparently they do not make side mounts.
?
There are plenty of less expensive imports - are any these any good?
--
John Hinman
Boise ID
Kappa 450X and A941

Re: Shop videos

 

I also use davinci resolve. I like that the pro version is a one time fee instead of a subscription, and it's an all-in-one software suite.
?
For recording, I upgraded to a crane jib and love it.
--
?
Larry Long Neck
Just a noob trying to learn the ways of wood

> Making youtube videos now!
??? -

Drawer slide recommendations

 

I am putting together another bank of drawers for my shop, and am looking for recommendations for drawer slides. Boxes are 35¡± wide, and will carry both heavy and light loads.
?
I¡¯m the past I have used Accuride side mounts, but the last I bought was disappointing. I like the rigidity of side mounts, and I do not care that the hardware is visible. I just want drawers that open and close smoothly and quietly.
?
Blum is a good brand, but apparently they do not make side mounts.
?
There are plenty of less expensive imports - are any these any good?
--
John Hinman
Boise ID
Kappa 450X and A941

Re: Shop videos

 

Rohit,
?
I use DaVinci Resolve 19.? It is pretty powerful, one time charge and updates pretty frequently.? If you have a powerful PC and a graphics card, it can use the acceleration.
?
It can do almost anything.? I learn how to use it more and more as I go.
?
PK

Re: Some questions on the Overhead Guard

 

¿ªÔÆÌåÓý

Sorry the sticker post was supposed to go to a private person. Sorry for the post.
Mac,,,

martin/campshure/co/llc
mac campshure
7412 elmwood ave.
middleton, wi 53562-3106
608-332-2330?cell

Designing and building for 50 years


On Jan 5, 2025, at 7:09?AM, Ronnie via groups.io <picktool@...> wrote:

Re: Shop videos

 

David Best - thank you for posting this. ?I have been looking for a replacement for my Joby for tabletop (or slidertop). ?Good to see the Surui in action.
Rich Markiewicz

Re: Shop videos

 

I use iphone 14 pro for now. ?Just started doing more videos. ?I'm learning to edit them with LumaFusion on ipad. ?
I'm using concrete Home Depot bucket with gas pipe and 3D Printed articulating arm with Edelkrone FlexTILT head on it. ?Here is a little video overview i did of the setup
https://youtu.be/SVIpIAY98kc
?

Re: Some questions on the Overhead Guard

 

Sang Luu & his K700s was in your boat in '20
?
Ronnie

2101 - 2120 of 141086