|
Re: Felder K 700 S comsidering.
¿ªÔÆÌåÓýI am sorry but I also wanted to thank you for your service and happy retirement ?Imran Malik On Feb 1, 2024, at 9:02?AM, jcorrado72@... wrote:
? Hello, I appreciate this site as I have found lots of great information in my research.? Thank you in advance.? |
|
Re: Felder K 700 S comsidering.
¿ªÔÆÌåÓýHello and Welcome to the group. What is your name? We like posters to put their name in the closing ? If you want to explore used I regularly post on my FB (link below). Most are on the west coast but recall one in Chicago area not too long ago. These are well built machines but things do go wrong with new and old, so it is best if the owner is able to align and maintain these machines. Getting Felder to fix or align the machine is too expensive for most typical hobbiests except for the few who can afford it. My 2002 KF700 works just as good as new. With used you can check for table flatness, runout on arbor/spindle and functionality prior to purchase. Everyone is different but after buying 2002 KF new all other Felder machines (4) that I have were bought used. If you are not familiar with the machines lookup someone near you. This is a friendly group and you should be able to see the machine in person. I am in central Indiana so bit of a drive but happy to go over the machines that I have. Imran Malik On Feb 1, 2024, at 9:02?AM, jcorrado72@... wrote:
? Hello, I appreciate this site as I have found lots of great information in my research.? Thank you in advance.? |
|
Re: Felder K 700 S comsidering.
¿ªÔÆÌåÓýSeriously, you probably won¡¯t make any more money with the Felder than you would with the SawStop. So if what you want is a slider, I would say that the Felder is as good as the alternatives. Buy what you can afford and enjoy it. Trying to justify a hobby is tough. Having said that, the purchase delivery and setup of a Felder product is an undertaking of it itself, so be patient. You¡¯ve come to the right place for help.Again, Welcome¡ Bill Belanger? On Feb 1, 2024, at 07:12, Bill Belanger via groups.io <bllblngr@...> wrote:
|
|
Re: Felder K 700 S comsidering.
¿ªÔÆÌåÓýWelcome to the group!You can make a million bucks in woodworking, but you¡¯ll need to start with 2. LOL Bill Belanger? On Feb 1, 2024, at 07:02, jcorrado72@... wrote:
|
|
Re: Lamello Cantex for sale $2000
Kevin,? Is it more than twice as good as my Virutex lipping planer? I use that machine quite a bit and have very little complaints about it. Jason Holtz J. Holtz Furniture 3307 Snelling Ave. South Minneapolis, MN 55406 612.432.2765 -- Jason J. Holtz Furniture 3307 Snelling Ave. South Minneapolis, MN 55406 |
|
Re: Are Miter saws relevant with a great slider?
#poll-notice
hi David, no I dont have a F&F on my slider. I have a rip guide on left side of the slider, might be able to use it as F&F?? been wanting to use it but limited work space.?
|
|
Re: Sheet good recommendations
¿ªÔÆÌåÓýOn 31-1-2024 20:13, Andy wrote:
Ok, I had the impression that if you spend a little work you could automate this fairly easily, per the link posted in the previous mail, see below:Thanks Jonathan and David, I¡¯ve had JoinerCAD for a few months, I¡¯m pretty familiar with it. It definitely speeds up carcass and shelf creation, but it still requires the drudgery of importing STP files for each different connector. It also still requires you to physically place the connectors on the model rather than adapt to add the correct hardware spacing (or even type) On Jan 31, 2024, at 1:41 PM, Jonathan Martens <jonathan@...> wrote: Here is their Youtube channel with more show cases: , there is even a video on explaining how to create a autmated way of placing rafix S20 connectors: They have a few (very limited set) of them prepared already judging from the video and the link in the comment section:
Kind regards,
Jonathan |
|
Re: Mac Clamps for Sale
¿ªÔÆÌåÓýBrandon,2001 is pre Xroll but not an issue going to Xroll. Going the other way, from Xroll to pre-Xroll, if the nut is 1/2¡± thick the two bottom sides need to be chamfered vs square. Imran Malik On Jan 31, 2024, at 9:05?PM, Brandon Nickel <brandon.nickel@...> wrote:
?I see they're listed as for a 2001 KF700. Can anyone (Mac?) tell me if these will work on a 2018 KF700S? I'm not familiar with any changes that might have been made to the table or T-slot.?
|
|
Re: Are Miter saws relevant with a great slider?
#poll-notice
I keep my old Makita in the barn but seldom use it. Good for siding and rough outside projects. The Mafell ks400 is a worthy replacement tool for trim and especially scribe work.?
|
|
Re: Dro flipstop attachment.
toggle quoted message
Show quoted text
On Jan 31, 2024, at 7:01?PM, Chad75 <shouldercords@...> wrote:
?Imran,? I would love to know how to buy one. I haven't read every post so I must have missed it.??
|
|
Re: Are Miter saws relevant with a great slider?
#poll-notice
Hey Albert
Do you not have a Fritz & Franz jig for your slider?? (Google it plus other threads in the FOG have mentioned this) Probably the most used attachment or jig I use on my slider.? (My F&F needs to be made a lot better but even what I have makes cutting particularly small pieces easy and safe. Cheers David |
|
Re: Are Miter saws relevant with a great slider?
#poll-notice
¿ªÔÆÌåÓýThis is a great thread/poll. ? The crux of the matter, gathered from the various comments, plus my own experience: ?
?
?
?
? Conclusion: If you have the space, then keep your Kapex (or equivalent). But if you can use the space for anything else, anything else at all, ditch it. You¡¯ll miss it every once in a while, but then you¡¯ll be happy that you have space for that third bandsaw, or second sander, or multi-router, or whatever. ? Warm regards, Lucky ? Dr David Luckensmeyer ? |
imran
Bill Belanger
Jack Decker
Jason Holtz
Albert Lee
Jonathan Martens
Jim Fleming
David Luckensmeyer