I use maverick abrasives in my 43¡± wide belt. They are better than some other brands I¡¯ve used. Great belt life.?
toggle quoted message
Show quoted text
On Feb 15, 2022, at 2:15 PM, Brian Lamb <blamb11@...> wrote:
? Combat Abrasives is a division of Maverick. I use their 2x72¡± belts on my grinder/sander and they work very well.
Anybody use?Maverick Abrasives on an edge sander or widebelt? Good, bad, ugly??
|
Combat Abrasives is a division of Maverick. I use their 2x72¡± belts on my grinder/sander and they work very well.
toggle quoted message
Show quoted text
Anybody use?Maverick Abrasives on an edge sander or widebelt? Good, bad, ugly??
|
I keep getting their ads in my feed. Never heard of them before. I'm currently using ZK713X zirconia alumina belts from VSM and they are great. So much longer lasting than anything else we've tried with the exception of ceramic which is a significant?jump in price. Jason Holtz
J. Holtz Furniture
3307 Snelling Ave. South Minneapolis, MN 55406
612 432-2765 -- Jason J. Holtz Furniture 3307 Snelling Ave. South Minneapolis, MN 55406
|
Anybody use?Maverick Abrasives on an edge sander or widebelt? Good, bad, ugly??
|
Re: Sliding Table Installation
If you have an adjustable height table like a Fat 500 or Barth bench, you can do it with one person. ?Details of how I do it including videos are here:
David Best
https://www.instagram.com/davidpbest/
toggle quoted message
Show quoted text
How difficult is installation of the sliding table on a K700S?
I will have Felder commission my new saw, which will have the 3200 mm table. The salesperson says this includes installing the sliding table. The user manual, however, recommends getting two or three helpers to assist with installation of the sliding table. That seems like a disconnect, since it is unlikely that Felder will send three guys to set up my saw.
I¡¯m just curious what other people have experienced.
Thanks!
--
John Hinman
Boise ID
Not a Felder Owner yet - expecting K700S in February and A941 in April 2022
|
Re: Sliding Table Installation
I¡¯ve done it myself twice. Once like Mac said and the next with the Fat 300. It can be done¡ Bill Belanger
Not that I¡¯ve done it100 times put slider on saw horse and slide the machine in to it with pallet Jack. On person operation. Mac,,, Designing and building for 50 years ? If you do it yourself, get a Harbor Freight lift cart Dave Davies I was able to do it myself on the k940, use 2 saw horses leveled to where it could be slid on.?
The k700 was done with one tech and me guiding it per his command. On Feb 15, 2022, at 10:05 AM, Mark Foster <mfsta2lt@...> wrote:
?I did it with 2 helpers, both as clueless as me. ? ?How difficult is installation of the sliding table on a K700S?
I will have Felder commission my new saw, which will have the 3200 mm table. The salesperson says this includes installing the sliding table. The user manual, however, recommends getting two or three helpers to assist with installation of the sliding table. That seems like a disconnect, since it is unlikely that Felder will send three guys to set up my saw.
I¡¯m just curious what other people have experienced.
Thanks!
--
John Hinman
Boise ID
Not a Felder Owner yet - expecting K700S in February and A941 in April 2022
-- Mark Foster
-- Dave & Marie Davies
318-219-7868
|
Re: Sliding Table Installation
You will need sawhorses or something to put it on at the height of the bolts even with 2-3 people, it needs to be threaded onto the bolts?
toggle quoted message
Show quoted text
On Feb 15, 2022, at 12:40 PM, John Hinman <jhinman1911@...> wrote:
?Sounds like a variety of experiences. I¡¯ll ask the Felder service planning people for clarification. I don¡¯t want to be building sawhorses and/or running around town trying to rent a hoist or pallet jack while the technician is cooling his heels.
--
John Hinman
Boise ID
Not a Felder Owner yet - expecting K700S in February and A941 in April 2022
|
Re: Sliding Table Installation
Sounds like a variety of experiences. I¡¯ll ask the Felder service planning people for clarification. I don¡¯t want to be building sawhorses and/or running around town trying to rent a hoist or pallet jack while the technician is cooling his heels.
--
John Hinman
Boise ID
Not a Felder Owner yet - expecting K700S in February and A941 in April 2022
|
Re: Sliding Table Installation
Not that I¡¯ve done it100 times put slider on saw horse and slide the machine in to it with pallet Jack. On person operation. Mac,,, Designing and building for 50 years
toggle quoted message
Show quoted text
On Feb 15, 2022, at 9:31 AM, David Davies <myfinishingtouch@...> wrote:
? If you do it yourself, get a Harbor Freight lift cart Dave Davies I was able to do it myself on the k940, use 2 saw horses leveled to where it could be slid on.?
The k700 was done with one tech and me guiding it per his command. On Feb 15, 2022, at 10:05 AM, Mark Foster <mfsta2lt@...> wrote:
?I did it with 2 helpers, both as clueless as me. ? ?How difficult is installation of the sliding table on a K700S?
I will have Felder commission my new saw, which will have the 3200 mm table. The salesperson says this includes installing the sliding table. The user manual, however, recommends getting two or three helpers to assist with installation of the sliding table. That seems like a disconnect, since it is unlikely that Felder will send three guys to set up my saw.
I¡¯m just curious what other people have experienced.
Thanks!
--
John Hinman
Boise ID
Not a Felder Owner yet - expecting K700S in February and A941 in April 2022
-- Mark Foster
-- Dave & Marie Davies
318-219-7868
|
Re: Sliding Table Installation
I have installed the 3200mm slider by my self. I used a ceiling winch to lift back end and handled the front (threading into chassis bolts). It is very doable by 2, if you have a hydraulic lift table or as Mark mentioned saw horses that can be adjusted to appropriate height.
YMMV,
Imran
toggle quoted message
Show quoted text
On Feb 15, 2022, at 10:00 AM, John Hinman <jhinman1911@...> wrote: ?How difficult is installation of the sliding table on a K700S?
I will have Felder commission my new saw, which will have the 3200 mm table. The salesperson says this includes installing the sliding table. The user manual, however, recommends getting two or three helpers to assist with installation of the sliding table. That seems like a disconnect, since it is unlikely that Felder will send three guys to set up my saw.
I¡¯m just curious what other people have experienced.
Thanks!
--
John Hinman
Boise ID
Not a Felder Owner yet - expecting K700S in February and A941 in April 2022
|
Re: Sliding Table Installation
If you do it yourself, get a Harbor Freight lift cart Dave Davies
I was able to do it myself on the k940, use 2 saw horses leveled to where it could be slid on.?
The k700 was done with one tech and me guiding it per his command. On Feb 15, 2022, at 10:05 AM, Mark Foster <mfsta2lt@...> wrote:
?I did it with 2 helpers, both as clueless as me. ? ?How difficult is installation of the sliding table on a K700S?
I will have Felder commission my new saw, which will have the 3200 mm table. The salesperson says this includes installing the sliding table. The user manual, however, recommends getting two or three helpers to assist with installation of the sliding table. That seems like a disconnect, since it is unlikely that Felder will send three guys to set up my saw.
I¡¯m just curious what other people have experienced.
Thanks!
--
John Hinman
Boise ID
Not a Felder Owner yet - expecting K700S in February and A941 in April 2022
-- Mark Foster
-- Dave & Marie Davies
318-219-7868
|
Re: Sliding Table Installation
I was able to do it myself on the k940, use 2 saw horses leveled to where it could be slid on.?
The k700 was done with one tech and me guiding it per his command.
toggle quoted message
Show quoted text
On Feb 15, 2022, at 10:05 AM, Mark Foster <mfsta2lt@...> wrote:
? I did it with 2 helpers, both as clueless as me. ? On Feb 15, 2022, at 07:00, John Hinman <Jhinman1911@...> wrote:
?How difficult is installation of the sliding table on a K700S?
I will have Felder commission my new saw, which will have the 3200 mm table. The salesperson says this includes installing the sliding table. The user manual, however, recommends getting two or three helpers to assist with installation of the sliding table. That seems like a disconnect, since it is unlikely that Felder will send three guys to set up my saw.
I¡¯m just curious what other people have experienced.
Thanks!
--
John Hinman
Boise ID
Not a Felder Owner yet - expecting K700S in February and A941 in April 2022
-- Mark Foster
|
Re: Sliding Table Installation
I did it with 2 helpers, both as clueless as me. ?
toggle quoted message
Show quoted text
On Feb 15, 2022, at 07:00, John Hinman <Jhinman1911@...> wrote:
?How difficult is installation of the sliding table on a K700S?
I will have Felder commission my new saw, which will have the 3200 mm table. The salesperson says this includes installing the sliding table. The user manual, however, recommends getting two or three helpers to assist with installation of the sliding table. That seems like a disconnect, since it is unlikely that Felder will send three guys to set up my saw.
I¡¯m just curious what other people have experienced.
Thanks!
--
John Hinman
Boise ID
Not a Felder Owner yet - expecting K700S in February and A941 in April 2022
--
Mark Foster
|
Re: Sliding Table Installation
I didn¡¯t have my unit commissioned but yes it took 3 of us to install the slider.? Steve Lyde
toggle quoted message
Show quoted text
On Feb 15, 2022, at 9:00 AM, John Hinman <jhinman1911@...> wrote:
?How difficult is installation of the sliding table on a K700S?
I will have Felder commission my new saw, which will have the 3200 mm table. The salesperson says this includes installing the sliding table. The user manual, however, recommends getting two or three helpers to assist with installation of the sliding table. That seems like a disconnect, since it is unlikely that Felder will send three guys to set up my saw.
I¡¯m just curious what other people have experienced.
Thanks!
--
John Hinman
Boise ID
Not a Felder Owner yet - expecting K700S in February and A941 in April 2022
|
Sliding Table Installation
How difficult is installation of the sliding table on a K700S?
I will have Felder commission my new saw, which will have the 3200 mm table. The salesperson says this includes installing the sliding table. The user manual, however, recommends getting two or three helpers to assist with installation of the sliding table. That seems like a disconnect, since it is unlikely that Felder will send three guys to set up my saw.
I¡¯m just curious what other people have experienced.
Thanks!
--
John Hinman
Boise ID
Not a Felder Owner yet - expecting K700S in February and A941 in April 2022
|
Martin, where are you located?
chris
|
Looking for Automatic Edgebander Recommendations
Hi guys, I¡¯ve long been toying with the idea of investing in a new automatic edgebander. I¡¯ve done extensive research on different brands, specs, price points, and have narrowed down a few key requirements. Figured you guys would be a great place to go for some info.?
First, I¡¯d like a pre-milling unit
Second, I¡¯m looking for around 50mm or 2¡± height capacity for floating shelving I do a lot of (the Felder maxes out at 45mm or 1.75¡±)
I don¡¯t do a lot of pvc or vinyls, mainly solid wood strips and wood tape so corner rounding is not a necessity.?
Currently I¡¯ve narrowed it down to 2 units: A Felder G360, and a CEHISA Compact S machine.?
The CEHISA machine has 8-60 mm capacity which is really nice to have. Meanwhile the Felder has 10-45 mm capacity which is pretty common on branders in this price range of $25k +\-.
Here¡¯s a link to a CEHISA from Capital Woods Machinery in Florida. I have had a great experience purchasing my Timesaver Speedsander 43¡± wide belt from them.?
Attached is a file for a G360 quote to compare specs for those interested.?
|
toggle quoted message
Show quoted text
Michael,
It¡¯s already in my store on CafePress: ?
If you want a thong version, let me know and I¡¯ll add it to the shop.
<Do You.jpg>
On Feb 13, 2022, at 9:16 AM, Michael Garrison Stuber < mtgstuber@...> wrote:
I feel like we need some new Felder Swag: "It's 11 o'clock . . . do you know where your dial indicator is?"
Same here.
<screenshot_5462.jpg>
On Feb 13, 2022, at 8:14 AM, Brian Lamb < blamb11@...>
wrote:
I
keep a dial indicator on a stand handy at all times,
sits on top of one of my roll aways. Setting the fence
to the blade is always going to give you some error,
unless your set up tool allows for the toe out of the
blade. You need to set fences, straight or angled to the
axis of movement of the slider.
Brian,
I definitely do not want
to bring a dial indicator out every time I
need to set to 45. Yes, my statement was not
the best but I had mentioned earlier that I
want something quick and to me referencing
blade and fence is the quickest method. I did
not mean to imply that it is the only method.
Imran
On Feb 13, 2022, at 10:20 AM, Brian Lamb < blamb11@...>
wrote:
?
Your statement makes no sense. You use the
square to set the angle of the fence, using a
dial indicator on a stand to indicate the one
edge. The blade has nothing to do with it.
Once the fence is at 45? accurately, you can
cut anything you want.
--
Michael Garrison Stuber
|
Michael,
It¡¯s already in my store on CafePress: ?
If you want a thong version, let me know and I¡¯ll add it to the shop.
David Best
https://www.instagram.com/davidpbest/
toggle quoted message
Show quoted text
On Feb 13, 2022, at 9:16 AM, Michael Garrison Stuber < mtgstuber@...> wrote:
I feel like we need some new Felder Swag: "It's 11 o'clock . . . do you know where your dial indicator is?"
Same here.
<screenshot_5462.jpg>
On Feb 13, 2022, at 8:14 AM, Brian Lamb < blamb11@...>
wrote:
I
keep a dial indicator on a stand handy at all times,
sits on top of one of my roll aways. Setting the fence
to the blade is always going to give you some error,
unless your set up tool allows for the toe out of the
blade. You need to set fences, straight or angled to the
axis of movement of the slider.
Brian,
I definitely do not want
to bring a dial indicator out every time I
need to set to 45. Yes, my statement was not
the best but I had mentioned earlier that I
want something quick and to me referencing
blade and fence is the quickest method. I did
not mean to imply that it is the only method.
Imran
On Feb 13, 2022, at 10:20 AM, Brian Lamb < blamb11@...>
wrote:
?
Your statement makes no sense. You use the
square to set the angle of the fence, using a
dial indicator on a stand to indicate the one
edge. The blade has nothing to do with it.
Once the fence is at 45? accurately, you can
cut anything you want.
--
Michael Garrison Stuber
|
Re: K 700 S, Did Felder cheap out on the rip fence?
I have one on my bandsaw and it¡¯s great! Of course it reads minus in this situation but its very easy to zero to make an adjustment.
Bill Belanger 
How good are the aftermarket DRO? It looks like a Wixey is $120 for a fence.
The Wixey I put on my thicknesses is pretty accurate.
--
John Hinman
Boise ID
Not a Felder Owner yet - expecting K700S in February and A941 in April 2022
|
Dan Gavrilyuk
Jason Holtz
David P. Best
Bill Belanger
imran
Mark Foster