Are you sure:
Price for a fat 300 equivalent on Ruwi web site seems to be 1,500 Euro + Tax + Shipping. Looks like the same price as what is quoted on the us felder shop website with the top at $400 ($2,000 total) if you get it from any of their warehouses in the US. Shipping From Germany to any east ports in the USA is not cheap.
Bill
|
Re: Dual unit analog scale for Hammer rip fence
Starrett Measurestix, they come in 1/2 and 3/4” wide versions with inch, inch/metric or metric markings.
toggle quoted message
Show quoted text
Hi all,
I am a new member to the group. I have a Hammer K3 that was delivered with a dual scale on the outrigger crosscut fence and a metric scale on the fixed table's rip fence. I would like to replace the metric scale with an imperial version (or a metric/imperial) but am having trouble finding one that will fit the extrusion's slot. The extrusion on the Hammer is 19mm (3/4"), I have searched the group's topics and I see that some have replaced their scales with a scale purchased from MSC. I may be that they were retrofitting a Felder product that possibly has a different width slot for the scale. I can find an SPI scale that is dual units and is 3/4" wide but it appears one side is imperial and the other is metric. If all else fails I can use this but I would prefer to have the dual units on the same side. Before I purchase the SPI, does anyone have a source for what I am looking for.
Thanks,
Kevin
|
ruwi make the felder table
felder charge double just to rebrand
i suggest you buy a ruwi
if you can
|
Dual unit analog scale for Hammer rip fence
Hi all,
I am a new member to the group. I have a Hammer K3 that was delivered with a dual scale on the outrigger crosscut fence and a metric scale on the fixed table's rip fence. I would like to replace the metric scale with an imperial version (or a metric/imperial) but am having trouble finding one that will fit the extrusion's slot. The extrusion on the Hammer is 19mm (3/4"), I have searched the group's topics and I see that some have replaced their scales with a scale purchased from MSC. I may be that they were retrofitting a Felder product that possibly has a different width slot for the scale. I can find an SPI scale that is dual units and is 3/4" wide but it appears one side is imperial and the other is metric. If all else fails I can use this but I would prefer to have the dual units on the same side. Before I purchase the SPI, does anyone have a source for what I am looking for.
Thanks,
Kevin
|
Hello Felder users....
I have an older, about 14 years old, AD 741.? It has the straight blades and the powerdrive and is currently working fine.
I am considering getting a Byrd-Shelix spiral cutter head for it.
I would like to speak with anyone who has done this conversion.
IF you have done this, would you PLEASE contact me?
I can be reached by phone or text at 707-591-6840
Thanks much
|
Re: Digi compensation for droll outrigger
Really? I haven’t heard about that the 1/100 degree. Maybe my iPhone’s Siri was on and Felder tapped in and heard me bit#4ing about the 1/10 degree capability not being good enough?! LOL
Lucky
toggle quoted message
Show quoted text
Hey Lucky,?
The latest spec for the X-roll outrigger now to 1/100 of a degree! I'm back to considering the K940 again because I might be able to get the X-Roll outrigger (long story! outlined in my DM to you).
Cheers
Michael ?
|
Re: Finger Pulls on Drawer fronts
I am not totally sure I understand the question.? Without letting that stop me, I can say I recently got decent results by shaping shortgrain strips into curved pulls with a tenon for attachment to the cabinet. Photos attached.??
I made blanks in pairs, routed the tenons with a straight bit on the router table, routed the concave curve with a large bull nose bit (two overlapping passes) and shaped the convex curve with spoke shave, plane, rasp and sand paper.? Deciding when to make which router pass and when to separate the halves is important.
|
Re: Finger Pulls on Drawer fronts
Ha I didn’t even catch the spelling thing.? I’ve never used any of the 700 species
?
?
toggle quoted message
Show quoted text
From: [email protected] < [email protected]>
On Behalf Of Jay Perrine
Sent: Monday, May 10, 2021 1:06 PM
To: [email protected]
Subject: Re: [FOG] Finger Pulls on Drawer fronts
?
?
Almost for sure Bob means Eucalyptus which has so many species (wikipedia says 700 species!) it could be blue gum or red or who knows what as it is mostly native to Australia (with Gidday that is a hint).? Twisting a big issue, but my understanding
is that is more species specific but hard and I'll take his word splintery.? There have been attempts at making flooring with it (maybe in CA where I live) under trade names like Blue something with no hint it's actually eucalyptus.? Fast growing and drops
stuff (essentially poisonous to other plants) around tree so nothing else grows and devastating in fires as the oils ignite into nice hot fire. ?
?
I am not familiar with Ecalypt.? When I have a cut like that in wood that burns easily I
do two things.
-
Buy a new bit from a quality brand
-
Make shallow cuts so the router does not have to slow down at all.
?
?
Gidday
Have a client from hell, fussy, AKA my daughter and partner
The want solid timber vanities 2x, made from recycled eucalypt ( hard and spllntery)
It will be oiled, I would like to keep burning to a minimum. The long section of the cut is in side grain, the returns in endgrain
Either hand router or Router insert in Felder KF
Seems to be only two bits- Ogee or a Finger Pull bit like the CMT one
Any comments on how to approach it?
Or should I find another daughter?
|
Re: Finger Pulls on Drawer fronts
? Almost for sure Bob means Eucalyptus which has so many species (wikipedia says 700 species!) it could be blue gum or red or who knows what as it is mostly native to Australia (with Gidday that is a hint).? Twisting a big issue, but my understanding is that is more species specific but hard and I'll take his word splintery.? There have been attempts at making flooring with it (maybe in CA where I live) under trade names like Blue something with no hint it's actually eucalyptus.? Fast growing and drops stuff (essentially poisonous to other plants) around tree so nothing else grows and devastating in fires as the oils ignite into nice hot fire. ? Jay in San Jose
toggle quoted message
Show quoted text
I am not familiar with Ecalypt.? When I have a cut like that in wood that burns easily I do two things.
-
Buy a new bit from a quality brand
-
Make shallow cuts so the router does not have to slow down at all.
?
?
Gidday
Have a client from hell, fussy, AKA my daughter and partner
The want solid timber vanities 2x, made from recycled eucalypt ( hard and spllntery)
It will be oiled, I would like to keep burning to a minimum. The long section of the cut is in side grain, the returns in endgrain
Either hand router or Router insert in Felder KF
Seems to be only two bits- Ogee or a Finger Pull bit like the CMT one
Any comments on how to approach it?
Or should I find another daughter?
|
On 5/6/21 12:25 PM, imranindiana via groups.io wrote: thought, I just checkout the how to video. On my iphone, I You whippersnappers and your unbelievably? good eyes. I can't use a smartphone for that.
|
Re: Finger Pulls on Drawer fronts
?????? A new bit and thin cuts are good. I like the tape idea. It's going to burn when you slow down to go around the corner to the endgrain. Keep it moving. Sandpaper will take out light burns. Conversion varnish will outlast oil when it comes to kitchens and baths. How do I know?? Now that's a long story....
|
Re: Finger Pulls on Drawer fronts
She’s your daughter, AND partner. ?Let her do it!
LOL,
Good luck,
Alex
toggle quoted message
Show quoted text
On May 9, 2021, at 10:45 PM, Bob Frizell <bob.frizell@...> wrote:
?Gidday
Have a client from hell, fussy, AKA my daughter and partner
The want solid timber vanities 2x, made from recycled eucalypt ( hard and spllntery)
It will be oiled, I would like to keep burning to a minimum. The long section of the cut is in side grain, the returns in endgrain
Either hand router or Router insert in Felder KF
Seems to be only two bits- Ogee or a Finger Pull bit like the CMT one
Any comments on how to approach it?
Or should I find another daughter?
|
Re: Finger Pulls on Drawer fronts
Carbide and listening to the whine of the motor to adjust speed will do it. Throw a couple pieces of tape on your jig/template then remove for the final pass so that it is a very thin cut.? Taylor Donsker www.tdonsker.com 818.424.9046
toggle quoted message
Show quoted text
On May 10, 2021, at 8:26 AM, Brian Lamb <blamb11@...> wrote:
? And jig it so you can move fast and not dwell.
I am not familiar with Ecalypt.? When I have a cut like that in wood that burns easily I do two things. - Buy a new bit from a quality brand
- Make shallow cuts so the router does not have to slow down at all.
? ? Gidday
Have a client from hell, fussy, AKA my daughter and partner
The want solid timber vanities 2x, made from recycled eucalypt ( hard and spllntery)
It will be oiled, I would like to keep burning to a minimum. The long section of the cut is in side grain, the returns in endgrain
Either hand router or Router insert in Felder KF
Seems to be only two bits- Ogee or a Finger Pull bit like the CMT one
Any comments on how to approach it?
Or should I find another daughter??
|
Re: Finger Pulls on Drawer fronts
Depending on their preferences, you can ask them if they like something with a more cove-y profile:
but from what I've heard about eucalypt (all from Derek Cohen) I'd agree with Joe -- get a shiny, new bit from a quality mfr and sneak up on it
|
Re: Finger Pulls on Drawer fronts
And jig it so you can move fast and not dwell.
toggle quoted message
Show quoted text
I am not familiar with Ecalypt.? When I have a cut like that in wood that burns easily I do two things. - Buy a new bit from a quality brand
- Make shallow cuts so the router does not have to slow down at all.
? ? Gidday
Have a client from hell, fussy, AKA my daughter and partner
The want solid timber vanities 2x, made from recycled eucalypt ( hard and spllntery)
It will be oiled, I would like to keep burning to a minimum. The long section of the cut is in side grain, the returns in endgrain
Either hand router or Router insert in Felder KF
Seems to be only two bits- Ogee or a Finger Pull bit like the CMT one
Any comments on how to approach it?
Or should I find another daughter??
|
Re: Finger Pulls on Drawer fronts
I am not familiar with Ecalypt.? When I have a cut like that in wood that burns easily I do two things.
-
Buy a new bit from a quality brand
-
Make shallow cuts so the router does not have to slow down at all.
?
toggle quoted message
Show quoted text
From: [email protected] < [email protected]>
On Behalf Of Bob Frizell
Sent: Sunday, May 9, 2021 10:46 PM
To: [email protected]
Subject: [FOG] Finger Pulls on Drawer fronts
?
Gidday
Have a client from hell, fussy, AKA my daughter and partner
The want solid timber vanities 2x, made from recycled eucalypt ( hard and spllntery)
It will be oiled, I would like to keep burning to a minimum. The long section of the cut is in side grain, the returns in endgrain
Either hand router or Router insert in Felder KF
Seems to be only two bits- Ogee or a Finger Pull bit like the CMT one
Any comments on how to approach it?
Or should I find another daughter?
|
Finger Pulls on Drawer fronts
Gidday
Have a client from hell, fussy, AKA my daughter and partner
The want solid timber vanities 2x, made from recycled eucalypt ( hard and spllntery)
It will be oiled, I would like to keep burning to a minimum. The long section of the cut is in side grain, the returns in endgrain
Either hand router or Router insert in Felder KF
Seems to be only two bits- Ogee or a Finger Pull bit like the CMT one
Any comments on how to approach it?
Or should I find another daughter?
|
Re: Digi compensation for droll outrigger
Hey Lucky,?
The latest spec for the X-roll outrigger now to 1/100 of a degree! I'm back to considering the K940 again because I might be able to get the X-Roll outrigger (long story! outlined in my DM to you).
Cheers
Michael ?
|
Re: Radial Drill Press purchase
Make sense, limit switches to save damaged machine from accidental over run. Designing and building for 50 years
toggle quoted message
Show quoted text
On May 8, 2021, at 2:22 PM, joelgelman via groups.io <joelgelman@...> wrote:
?On the power lift, I do not think I will care about fine adjustment. ?As I see it, I will raise or lower the head when needed to accommodate a different thickness of wood with a different bit or the same wood with a different bit. ?I am just looking for ballpark to make sure I can get the bit in and then lower the bit when drilling as needed before running out of quill travel. ?Once I change the bit, I have to adjust the depth stop and that is where the fine adjustment happens. ?
Maybe I am missing something, and not too late for refinements in the modifications. ?
|
Re: Radial Drill Press purchase
On the power lift, I do not think I will care about fine adjustment. ?As I see it, I will raise or lower the head when needed to accommodate a different thickness of wood with a different bit or the same wood with a different bit. ?I am just looking for ballpark to make sure I can get the bit in and then lower the bit when drilling as needed before running out of quill travel. ?Once I change the bit, I have to adjust the depth stop and that is where the fine adjustment happens. ?
Maybe I am missing something, and not too late for refinements in the modifications. ?
|
Kevin Wells
David Luckensmeyer
Jim Fleming
Joe Jensen