Re: How to lift Tannewitz Bandsaw off pallet
I bought a HF gantry crane to lift my MM bandsaw off the pallet Dave Davies
On Sat, Oct 10, 2020 at 11:26 AM David Kumm < davekumm@...> wrote:
I've not lifted mine but I'm assuming the top wheel itself is too high and not just the guard rail.? The good news is a good condition PH probably has better resale value than a 36".? They are much rarer.? Dave
Hi all, I am back from picking up the Tannewitz I bought on auction.? I'm disappointed that it was a PH 30" and not a 36" but that's a risk I took with the sketchy listing.? At $775 with only one small broken part I think I did ok.? It's in a the bed of
a drop deck trailer out front of my shop. The pallet its strapped to is 6" high making it a couple inches too tall to roll into the shop.? I want to lift it off the pallet and place the permanent oak skids underneath.? I don't see any factory lift points.?
?I'm sure someone here has done this.? There will be many more questions, the brake system must be non-functional as an electronic brake.? I will want to get that all back to original
-- Dave & Marie Davies
318-219-7868
|
Re: How to lift Tannewitz Bandsaw off pallet
I've not lifted mine but I'm assuming the top wheel itself is too high and not just the guard rail.? The good news is a good condition PH probably has better resale value than a 36".? They are much rarer.? Dave
toggle quoted message
Show quoted text
Hi all, I am back from picking up the Tannewitz I bought on auction.? I'm disappointed that it was a PH 30" and not a 36" but that's a risk I took with the sketchy listing.? At $775 with only one small broken part I think I did ok.? It's in a the bed of
a drop deck trailer out front of my shop. The pallet its strapped to is 6" high making it a couple inches too tall to roll into the shop.? I want to lift it off the pallet and place the permanent oak skids underneath.? I don't see any factory lift points.?
?I'm sure someone here has done this.? There will be many more questions, the brake system must be non-functional as an electronic brake.? I will want to get that all back to original
|
How to lift Tannewitz Bandsaw off pallet
Hi all, I am back from picking up the Tannewitz I bought on auction.? I'm disappointed that it was a PH 30" and not a 36" but that's a risk I took with the sketchy listing.? At $775 with only one small broken part I think I did ok.? It's in a the bed of a drop deck trailer out front of my shop. The pallet its strapped to is 6" high making it a couple inches too tall to roll into the shop.? I want to lift it off the pallet and place the permanent oak skids underneath.? I don't see any factory lift points.? ?I'm sure someone here has done this.? There will be many more questions, the brake system must be non-functional as an electronic brake.? I will want to get that all back to original
|
On Wed, Oct 7, 2020 at 12:46 PM, David W wrote:
I have an older A3-31, and if I do not keep the planer bed waxed, I get “grabbing” and snipe in the infeed. ?I don’t know if this will help on the out feed. ?I use Johnson furniture wax to lubricate the jointer and planer beds.
-David
?Hey David, ?I? do keep the the table well waxed with a similar product. Thanks for the input?
|
Re: Hammer C3 31 Electrical issue
#hammer
So it turns out that the brake board was bad.? I ordered a new one from Klinger Born in Germany for about 118 Euros (including shipping).? I replaced the brake board, and everything started right up with no further issues.
|
Re: Cutting mitered bridal joint
Pretty sure I shot for a 4” wide bevel, but it’s been so many years ago I can’t remember for sure. I know I needed the whole 12” blade.
toggle quoted message
Show quoted text
FWIW, i found this used on Ebay in April. the cutting length is 60mm. it will do a bevel similar to Brian’s table but not sure if it can do exactly what Brian did. <image0.jpeg>
imran ? Maybe you should have used a chisel :) Dave Davies On Fri, Oct 9, 2020 at 7:45 AM Brian Lamb < blamb11@...> wrote: A tall cutter would have worked on smaller parts, but that table was over 6’ long and I might have been able to do the two long edges, would have hit the ceiling trying to do the narrow ones. I’m sure a talented person could have done it with a hand plane… but that’s not me...
On Oct 8, 2020, at 8:43 PM, Mark Foster < mfsta2lt@...> wrote:
Brian,
This is the major reason I bought the KF with a 9’ slider. I could just see doing something like this! I really like my 4” tall spiral cutter with bearing for profiling larger parts.
Mark Foster On Oct 8, 2020, at 8:01 PM, Brian Lamb < blamb11@...> wrote:
The bevel was a real butt pucker set up…. This picture is kind of dark, but you can see the shaper with the blade on it. I raised the actual table up with two layers of 3/4” ply to get it tall enough to cut as thin as I wanted, but not have the other end of the blade hit the table.?On Oct 8, 2020, at 7:05 PM, Mark Foster < mfsta2lt@...> wrote:
Brian,
Thank you for posting. I really like the Maple and Bubinga contrast. The taper on the underside of the table top is elegant.
Marl Foster On Oct 8, 2020, at 6:35 PM, Brian Lamb < blamb11@...> wrote:
Thank you! Like your table too, definitely a different look with the tenon on the lower section.On Oct 8, 2020, at 3:30 PM, mark thomas < murkyd@...> wrote:
Brian,?
Nice table, I like the 3-sided tapered legs and different wood feet.? Loosely reminds me of this walnut taper leg and koa foot I once did, which also has an odd mortise and tenon on diagonal.? ?
Michael, the stool is very nice, the joint seems perfect for it.? Is the one in photo tapered however?? ?How will you attach the slats?
<IMG_0695.jpeg>
-- Dave & Marie Davies
318-219-7868
|
Re: Cutting mitered bridal joint
FWIW, i found this used on Ebay in April. the cutting length is 60mm. it will do a bevel similar to Brian’s table but not sure if it can do exactly what Brian did.
imran
toggle quoted message
Show quoted text
On Oct 9, 2020, at 8:54 AM, David Davies <myfinishingtouch@...> wrote: ? Maybe you should have used a chisel :) Dave Davies On Fri, Oct 9, 2020 at 7:45 AM Brian Lamb < blamb11@...> wrote: A tall cutter would have worked on smaller parts, but that table was over 6’ long and I might have been able to do the two long edges, would have hit the ceiling trying to do the narrow ones. I’m sure a talented person could have done it with a hand plane… but that’s not me...
On Oct 8, 2020, at 8:43 PM, Mark Foster < mfsta2lt@...> wrote:
Brian,
This is the major reason I bought the KF with a 9’ slider. I could just see doing something like this! I really like my 4” tall spiral cutter with bearing for profiling larger parts.
Mark Foster On Oct 8, 2020, at 8:01 PM, Brian Lamb < blamb11@...> wrote:
The bevel was a real butt pucker set up…. This picture is kind of dark, but you can see the shaper with the blade on it. I raised the actual table up with two layers of 3/4” ply to get it tall enough to cut as thin as I wanted, but not have the other end of the blade hit the table.?On Oct 8, 2020, at 7:05 PM, Mark Foster < mfsta2lt@...> wrote:
Brian,
Thank you for posting. I really like the Maple and Bubinga contrast. The taper on the underside of the table top is elegant.
Marl Foster On Oct 8, 2020, at 6:35 PM, Brian Lamb < blamb11@...> wrote:
Thank you! Like your table too, definitely a different look with the tenon on the lower section.On Oct 8, 2020, at 3:30 PM, mark thomas < murkyd@...> wrote:
Brian,?
Nice table, I like the 3-sided tapered legs and different wood feet.? Loosely reminds me of this walnut taper leg and koa foot I once did, which also has an odd mortise and tenon on diagonal.? ?
Michael, the stool is very nice, the joint seems perfect for it.? Is the one in photo tapered however?? ?How will you attach the slats?
<IMG_0695.jpeg>
-- Dave & Marie Davies
318-219-7868
|
Re: Applying Biesemeyer Tape
Randy and Mark,
thanks for the feedback. i would do the clean and stick. just wanted to avoid the messy adhesive if possible.
imran?
toggle quoted message
Show quoted text
On Oct 9, 2020, at 9:12 AM, Randy Child via groups.io <strongman_one@...> wrote: ?
I stuck mine down after cleaning the fence with acetone.. never had an issue with it coming loose.. I did not use the spray adhesive either
On Friday, October 9, 2020, 06:07:36 AM PDT, Mark Kessler <mkessler10@...> wrote:
Imran, I do the same as Brian. Maybe if “substrate” is porous they are recommending that so the “substrate” doesn’t suck up some of the pre-applied stick on the tape and weaken the bond. ? On Oct 9, 2020, at 8:55 AM, Brian Lamb <blamb11@...> wrote:
?
The Starrett Measure-Stix I use are self adhesive and you can stick them to pretty much anything. I usually clean with an alcohol swab right before I stick them down to make sure no oils are present. My cross cut fences clamp the tape measures in place, they are not stuck down…. but I don’t have the short fence so maybe it’s different.
i got following for the short xcut fence.
even though it is adhesive backed, directions say to use a spray adhesive on the substrate before fixing it. i was not expecting to have to do that. does anyone know if this is necessary?
imran?
|
Re: Cutting mitered bridal joint
Thank you, that’s actually an ancient project, think it was about 2002. I couldn’t bring myself to sell or throw the table out when we sold that house and moved, so the top got repurposed to be the table for my 3D printer and the legs are still stuck on a shelf out in the shop for a possible future project.
Brian Lamb
blamb11@...
www.lambtoolworks.com
toggle quoted message
Show quoted text
On Oct 8, 2020, at 8:44 PM, David Luckensmeyer <dhluckens@...> wrote:
Wow! WTG Brian!!
Lucky
|
Re: Applying Biesemeyer Tape
thanks Brian. you are correct, the scale is held in channel not glued. i have not opened the package but i expect this to be not stiff enough to be used on it’s own. i intend to stick it to the AL band that came with the short xcut fence. i was torn between this and a steel option from mcmaster carr. there was not a good pic of scale markings on mcmaster and biesemeyer is recommended in survival guide.
BTW, not a fan of the AL bands. once accidentally bent it is almost impossible to make if lay flat.
imran
toggle quoted message
Show quoted text
On Oct 9, 2020, at 8:55 AM, Brian Lamb <blamb11@...> wrote: ? The Starrett Measure-Stix I use are self adhesive and you can stick them to pretty much anything. I usually clean with an alcohol swab right before I stick them down to make sure no oils are present. My cross cut fences clamp the tape measures in place, they are not stuck down…. but I don’t have the short fence so maybe it’s different.
i got following for the short xcut fence.
even though it is adhesive backed, directions say to use a spray adhesive on the substrate before fixing it. i was not expecting to have to do that. does anyone know if this is necessary?
imran?
|
Re: Applying Biesemeyer Tape
I stuck mine down after cleaning the fence with acetone.. never had an issue with it coming loose.. I did not use the spray adhesive either
On Friday, October 9, 2020, 06:07:36 AM PDT, Mark Kessler <mkessler10@...> wrote:
Imran, I do the same as Brian. Maybe if “substrate” is porous they are recommending that so the “substrate” doesn’t suck up some of the pre-applied stick on the tape and weaken the bond. ? On Oct 9, 2020, at 8:55 AM, Brian Lamb <blamb11@...> wrote:
?
The Starrett Measure-Stix I use are self adhesive and you can stick them to pretty much anything. I usually clean with an alcohol swab right before I stick them down to make sure no oils are present. My cross cut fences clamp the tape measures in place, they are not stuck down…. but I don’t have the short fence so maybe it’s different.
i got following for the short xcut fence.
even though it is adhesive backed, directions say to use a spray adhesive on the substrate before fixing it. i was not expecting to have to do that. does anyone know if this is necessary?
imran?
|
Re: Cutting mitered bridal joint
toggle quoted message
Show quoted text
Maybe you should have used a chisel :) Dave Davies On Fri, Oct 9, 2020 at 7:45 AM Brian Lamb < blamb11@...> wrote: A tall cutter would have worked on smaller parts, but that table was over 6’ long and I might have been able to do the two long edges, would have hit the ceiling trying to do the narrow ones. I’m sure a talented person could have done it with a hand plane… but that’s not me...
On Oct 8, 2020, at 8:43 PM, Mark Foster < mfsta2lt@...> wrote:
Brian,
This is the major reason I bought the KF with a 9’ slider. I could just see doing something like this! I really like my 4” tall spiral cutter with bearing for profiling larger parts.
Mark Foster On Oct 8, 2020, at 8:01 PM, Brian Lamb < blamb11@...> wrote:
The bevel was a real butt pucker set up…. This picture is kind of dark, but you can see the shaper with the blade on it. I raised the actual table up with two layers of 3/4” ply to get it tall enough to cut as thin as I wanted, but not have the other end of the blade hit the table.?On Oct 8, 2020, at 7:05 PM, Mark Foster < mfsta2lt@...> wrote:
Brian,
Thank you for posting. I really like the Maple and Bubinga contrast. The taper on the underside of the table top is elegant.
Marl Foster On Oct 8, 2020, at 6:35 PM, Brian Lamb < blamb11@...> wrote:
Thank you! Like your table too, definitely a different look with the tenon on the lower section.On Oct 8, 2020, at 3:30 PM, mark thomas < murkyd@...> wrote:
Brian,?
Nice table, I like the 3-sided tapered legs and different wood feet.? Loosely reminds me of this walnut taper leg and koa foot I once did, which also has an odd mortise and tenon on diagonal.? ?
Michael, the stool is very nice, the joint seems perfect for it.? Is the one in photo tapered however?? ?How will you attach the slats?
<IMG_0695.jpeg>
-- Dave & Marie Davies
318-219-7868
|
Re: Cutting mitered bridal joint
I built the legs and stand offs, drilled the mounting holes, laid the top upside down on a table, positioned the legs/base where I wanted it, spot drilled into the table bottom to mark the locations. Took the legs off and enlarged the holes in the top for brass inserts with machined threads on the inside, installed them. Then I took the base assembly and enlarged the holes from the top side part way thru. then, once everything was finished and bolted together, there was room for the bolts to tilt slightly with expansion and contraction.
Probably all over kill here in AZ, we don’t have much trouble with that sort of thing.
Brian Lamb
blamb11@...
www.lambtoolworks.com
toggle quoted message
Show quoted text
On Oct 9, 2020, at 5:54 AM, Marlowe McGraw <marlomcgraw@...> wrote:
Well done Brian! How did you account for movement of the top in your attachment?
Marlowe
|
Re: Applying Biesemeyer Tape
Imran, I do the same as Brian. Maybe if “substrate” is porous they are recommending that so the “substrate” doesn’t suck up some of the pre-applied stick on the tape and weaken the bond. ?
toggle quoted message
Show quoted text
On Oct 9, 2020, at 8:55 AM, Brian Lamb <blamb11@...> wrote:
? The Starrett Measure-Stix I use are self adhesive and you can stick them to pretty much anything. I usually clean with an alcohol swab right before I stick them down to make sure no oils are present. My cross cut fences clamp the tape measures in place, they are not stuck down…. but I don’t have the short fence so maybe it’s different.
i got following for the short xcut fence.
even though it is adhesive backed, directions say to use a spray adhesive on the substrate before fixing it. i was not expecting to have to do that. does anyone know if this is necessary?
imran?
|
Re: Applying Biesemeyer Tape
The Starrett Measure-Stix I use are self adhesive and you can stick them to pretty much anything. I usually clean with an alcohol swab right before I stick them down to make sure no oils are present. My cross cut fences clamp the tape measures in place, they are not stuck down…. but I don’t have the short fence so maybe it’s different.
toggle quoted message
Show quoted text
i got following for the short xcut fence.
even though it is adhesive backed, directions say to use a spray adhesive on the substrate before fixing it. i was not expecting to have to do that. does anyone know if this is necessary?
imran?
|
Re: Cutting mitered bridal joint
Well done Brian! How did you account for movement of the top in your attachment?
Marlowe?
On Fri, Oct 9, 2020, 7:45 AM Brian Lamb < blamb11@...> wrote: A tall cutter would have worked on smaller parts, but that table was over 6’ long and I might have been able to do the two long edges, would have hit the ceiling trying to do the narrow ones. I’m sure a talented person could have done it with a hand plane… but that’s not me...
On Oct 8, 2020, at 8:43 PM, Mark Foster < mfsta2lt@...> wrote:
Brian,
This is the major reason I bought the KF with a 9’ slider. I could just see doing something like this! I really like my 4” tall spiral cutter with bearing for profiling larger parts.
Mark Foster On Oct 8, 2020, at 8:01 PM, Brian Lamb < blamb11@...> wrote:
The bevel was a real butt pucker set up…. This picture is kind of dark, but you can see the shaper with the blade on it. I raised the actual table up with two layers of 3/4” ply to get it tall enough to cut as thin as I wanted, but not have the other end of the blade hit the table.?On Oct 8, 2020, at 7:05 PM, Mark Foster < mfsta2lt@...> wrote:
Brian,
Thank you for posting. I really like the Maple and Bubinga contrast. The taper on the underside of the table top is elegant.
Marl Foster On Oct 8, 2020, at 6:35 PM, Brian Lamb < blamb11@...> wrote:
Thank you! Like your table too, definitely a different look with the tenon on the lower section.On Oct 8, 2020, at 3:30 PM, mark thomas < murkyd@...> wrote:
Brian,?
Nice table, I like the 3-sided tapered legs and different wood feet.? Loosely reminds me of this walnut taper leg and koa foot I once did, which also has an odd mortise and tenon on diagonal.? ?
Michael, the stool is very nice, the joint seems perfect for it.? Is the one in photo tapered however?? ?How will you attach the slats?
<IMG_0695.jpeg>
|
Re: Cutting mitered bridal joint
Maybe you should have used a chisel :) Dave Davies
On Fri, Oct 9, 2020 at 7:45 AM Brian Lamb < blamb11@...> wrote: A tall cutter would have worked on smaller parts, but that table was over 6’ long and I might have been able to do the two long edges, would have hit the ceiling trying to do the narrow ones. I’m sure a talented person could have done it with a hand plane… but that’s not me...
On Oct 8, 2020, at 8:43 PM, Mark Foster < mfsta2lt@...> wrote:
Brian,
This is the major reason I bought the KF with a 9’ slider. I could just see doing something like this! I really like my 4” tall spiral cutter with bearing for profiling larger parts.
Mark Foster On Oct 8, 2020, at 8:01 PM, Brian Lamb < blamb11@...> wrote:
The bevel was a real butt pucker set up…. This picture is kind of dark, but you can see the shaper with the blade on it. I raised the actual table up with two layers of 3/4” ply to get it tall enough to cut as thin as I wanted, but not have the other end of the blade hit the table.?On Oct 8, 2020, at 7:05 PM, Mark Foster < mfsta2lt@...> wrote:
Brian,
Thank you for posting. I really like the Maple and Bubinga contrast. The taper on the underside of the table top is elegant.
Marl Foster On Oct 8, 2020, at 6:35 PM, Brian Lamb < blamb11@...> wrote:
Thank you! Like your table too, definitely a different look with the tenon on the lower section.On Oct 8, 2020, at 3:30 PM, mark thomas < murkyd@...> wrote:
Brian,?
Nice table, I like the 3-sided tapered legs and different wood feet.? Loosely reminds me of this walnut taper leg and koa foot I once did, which also has an odd mortise and tenon on diagonal.? ?
Michael, the stool is very nice, the joint seems perfect for it.? Is the one in photo tapered however?? ?How will you attach the slats?
<IMG_0695.jpeg>
-- Dave & Marie Davies
318-219-7868
|
Re: Cutting mitered bridal joint
A tall cutter would have worked on smaller parts, but that table was over 6’ long and I might have been able to do the two long edges, would have hit the ceiling trying to do the narrow ones. I’m sure a talented person could have done it with a hand plane… but that’s not me...
toggle quoted message
Show quoted text
On Oct 8, 2020, at 8:43 PM, Mark Foster < mfsta2lt@...> wrote:
Brian,
This is the major reason I bought the KF with a 9’ slider. I could just see doing something like this! I really like my 4” tall spiral cutter with bearing for profiling larger parts.
Mark Foster On Oct 8, 2020, at 8:01 PM, Brian Lamb < blamb11@...> wrote:
The bevel was a real butt pucker set up…. This picture is kind of dark, but you can see the shaper with the blade on it. I raised the actual table up with two layers of 3/4” ply to get it tall enough to cut as thin as I wanted, but not have the other end of the blade hit the table.?On Oct 8, 2020, at 7:05 PM, Mark Foster < mfsta2lt@...> wrote:
Brian,
Thank you for posting. I really like the Maple and Bubinga contrast. The taper on the underside of the table top is elegant.
Marl Foster On Oct 8, 2020, at 6:35 PM, Brian Lamb < blamb11@...> wrote:
Thank you! Like your table too, definitely a different look with the tenon on the lower section.On Oct 8, 2020, at 3:30 PM, mark thomas < murkyd@...> wrote:
Brian,?
Nice table, I like the 3-sided tapered legs and different wood feet.? Loosely reminds me of this walnut taper leg and koa foot I once did, which also has an odd mortise and tenon on diagonal.? ?
Michael, the stool is very nice, the joint seems perfect for it.? Is the one in photo tapered however?? ?How will you attach the slats?
<IMG_0695.jpeg>
|
i got following for the short xcut fence.
even though it is adhesive backed, directions say to use a spray adhesive on the substrate before fixing it. i was not expecting to have to do that. does anyone know if this is necessary?
imran?
|
Re: Cutting mitered bridal joint
toggle quoted message
Show quoted text
On 9 Oct 2020, at 1:01 pm, Brian Lamb < blamb11@...> wrote:
The bevel was a real butt pucker set up…. This picture is kind of dark, but you can see the shaper with the blade on it. I raised the actual table up with two layers of 3/4” ply to get it tall enough to cut as thin as I wanted, but not have the other end of the blade hit the table.?
On Oct 8, 2020, at 7:05 PM, Mark Foster < mfsta2lt@...> wrote:
Brian,
Thank you for posting. I really like the Maple and Bubinga contrast. The taper on the underside of the table top is elegant.
Marl Foster On Oct 8, 2020, at 6:35 PM, Brian Lamb < blamb11@...> wrote:
Thank you! Like your table too, definitely a different look with the tenon on the lower section.On Oct 8, 2020, at 3:30 PM, mark thomas < murkyd@...> wrote:
Brian,?
Nice table, I like the 3-sided tapered legs and different wood feet.? Loosely reminds me of this walnut taper leg and koa foot I once did, which also has an odd mortise and tenon on diagonal.? ?
Michael, the stool is very nice, the joint seems perfect for it.? Is the one in photo tapered however?? ?How will you attach the slats?
<IMG_0695.jpeg>
|
Joe Jensen
imran
David Luckensmeyer