Thanks All, I think I am going to give it a shot, I will setup some form of better venting and may have the insides shot with a bit of spray foam. Thanks Glen,
Alpine Moulding and Millwork Inc.
Mail: ?? P.O. Box 257 ?????????? Avery, CA. 95224 Shop: 441 Pennsylvania Gulch Road ????????? Murphys, CA. 95247
????????? 650-678-3137 LIC # 707507
On Tue, Jul 28, 2020 at 5:50 AM Trevor Lusty < trevlusty@...> wrote: Glenn,
? ? ? ? ? ?I ran a timber business in Northern Ireland for twenty four years. For approximately a five year period during that time, we stored all of our machined hardwoods and softwoods in twenty foot containers double stacked. On the ground floor containers, we racked them out with 2"x1" box iron frames in 24"x24" sections. Bolted an Elu chop saw on the inside of the door for easy ?cross cutting of the timber.
No more twists or shakes than normal, no damp or water ingress ,although we have a very different climate from you!?
Great for security, easy to reconfigure storage in your premises as no planning permission required, and no local council taxes applicable, as containers were regarded non permanent structures and we moved them around every six months.
Trevor Lusty
Ireland
|
Re: Aigner Distometer up alternative?
I vote to blame it on Mac too. LOL
Bill Belanger?
On Tue, Jul 28, 2020 at 7:25 PM Brian Lamb < blamb11@...> wrote: Well, it¡¯s Mac¡¯s fault then¡.
If I did that, then I would think the first post of this new thread would me mine.? Mac's is the first post of this thread version.? Maybe Mac thought this was such an important topic that it deserved 2 threads! :)
|
Re: Aigner Distometer up alternative?
Well, it¡¯s Mac¡¯s fault then¡.
toggle quoted message
Show quoted text
If I did that, then I would think the first post of this new thread would me mine. ?Mac's is the first post of this thread version. ?Maybe Mac thought this was such an important topic that it deserved 2 threads! :)
|
Re: AD941 vs. Baileigh JP-1898-NC
The spacer block I added was specific to the Comatic Smart Stand ?- ?to make it possible to swing the power feeder across the fence. ? Using the the power feeder stand from Felder, a spacer block was not required, but it was a hell of a lot of work cranking up the feeder every time to clear the fence - made even more challenging in my situation because the elevation crank for Felder feeder stand is behind the machine. ? Using a Smart Stand repositions the elevation crank to the the feeder itself, but it does impose the need for a spacer block at the mount since the stand is not as tall as the Felder version. ? You can see my setup here and why I wanted the crank height for the feeder moved to the front of the machine ?- which is what motivated my switch to the Comatic Smart Stand: ??
I have heard conflicting stories about the availability of a PF feeder bracket mounting space on the AD741 - it appears to be vintage specific as to whether the machine chassis has the mounting space and attachment points for the bracket.
David Best
https://www.instagram.com/davidpbest/
toggle quoted message
Show quoted text
David B and others have had to make the spacer to work in conjunction with using the Smart Stand if memory serves me right. Works fine with the standard PF mounting post. Also might need the longer extension tube. On Tue, Jul 28, 2020 at 4:15 PM Averman, Ed (FAA) via <Ed.Averman= [email protected]> wrote:
My AD 941 came with a PF mounting bracket installed in pre-drilled holes (I ordered it that way).? I think, as David Best has pointed out, for it to work practically, you need
to make a spacer block to get the PF high enough to clear the fence.? I haven¡¯t mounted a PF on mine yet, but what David said is correct.? He made one for his (AD 951 or Dual 51 (not sure which one he has)), and he has posted pictures, etc.?
? Skip ? From: [email protected] <[email protected]>
On Behalf Of David Davies
Sent: Tuesday, July 28, 2020 4:01 PM
To: [email protected]
Subject: Re: [FOG] AD941 vs. Baileigh JP-1898-NC ?
It will work on the AD951.? But as far as I know not the AD941
?
On Tue, Jul 28, 2020 at 2:56 PM Andy Wojteczko <andy@...> wrote:
Dave you should check with John as to how he knows it will work. Andy ?
? Could be, pretty sure Felder told me there was a way to do it because I asked when I bought mine.
?
Mark,
? I'm pretty sure you can't mount it on the AD941.? I have one and there are access panels in that location.
?
I believe i was told that you can mount the same bracket on the ad941, would need to drill the holes. chassis is the same except for the width
?
Another plus with the AD951 is the ability, with the optional mounting bracket to add a Power Feeder.?
-------- Original message --------
Date: 2020-07-28 2:35 p.m. (GMT-05:00)
Subject: Re: [FOG] AD941 vs. Baileigh JP-1898-NC
Sang, I was speaking from experience on AD941 - AD951 about $3500, is true though need to ask to get an accurate quote obviously...
?
Single phase 4hp i think ?(Whatever is the standard.?
The 3piece guard (which I don¡¯t think they say is standard on the web but they include it)
3p 7.5 hp i think (Whatever is the standard)
Variable speed (which is standard)
?
? On Jul 28, 2020, at 2:27 PM, Sang Luu <sangluu@...> wrote:
?I don't think it's correct to blanket assume you will get 951 standard options that would otherwise be options on the 941.
There are a lot of options on the 951 so I would simply just ask the rep to help guide your decision. They have the pricing structure, which none of us have.?
--
Dave & Marie Davies
318-219-7868
--
Andy Wojteczko
--
Dave & Marie Davies
318-219-7868
--
|
Re: AD941 vs. Baileigh JP-1898-NC
Brian is correct. ASAIK a riser is only required with smart stand to clear the fence. when i had a custom bracket fabricated for dual51, with ~6¡± riser, for smartstand installation a discussion ensued. there was one felder J/P model that did not have beefy enough structure behind to accommodate a PF. will need to find those old msgs to find out which one.
imran
toggle quoted message
Show quoted text
On Jul 28, 2020, at 2:13 PM, Brian Lamb <blamb11@...> wrote: ? I¡¯ve heard of some folks buying stuff related to metal working and it¡¯s all been re-badged Chinese units, quality is suspect to say the least. I haven¡¯t heard that they don¡¯t support you, but then I haven¡¯t paid that much attention. I try to do my best to not spend money in China...
On Jul 28, 2020, at 10:49 AM, Bill B¨¦langer < Bllblngr@...> wrote:
Thanks for that Brian. It does look quite impressive though. I wonder about the accuracy. My AD941 is spot on for thickness.
Bill Belanger? On Tue, Jul 28, 2020 at 1:43 PM Brian Lamb < blamb11@...> wrote: Chinese imports with the Baileigh name on them. Wouldn¡¯t be my choice at any price.
Hello,
I am about ready to pull the trigger on a AD941.? Then I see that this Baileigh beast is on sale for less than the quote I got for the AD941.? This unit does not require a switch over and has a power drive mech like an AD951.
Thoughts on Baileigh?
Paul
|
Re: Aigner Distometer up alternative?
If I did that, then I would think the first post of this new thread would me mine. ?Mac's is the first post of this thread version. ?Maybe Mac thought this was such an important topic that it deserved 2 threads! :)
|
Re: Aigner Distometer up alternative?
I see the problem, somehow you have created two separate threads with slightly different titles.
toggle quoted message
Show quoted text
Oh.... now when on the main page by topics I see that this topic is in 2 parts with the same title. ?
|
Re: AD941 vs. Baileigh JP-1898-NC
I almost bought something from them.? I preceeded the? purchase
with a query about? tolerances? run out that sort of thing.
They sent me a hat.
No specifications were available. Baileigh? doesn't even have
specifications they don't know what class bearings are in the?
machinery? what tolerances the machines can hold? they don't know
much of anything at all.
I had the same problem with Laguna.? They are just a reseller of
other people's junk.
On 7/28/20 11:52 AM, PK wrote:
toggle quoted message
Show quoted text
Hello,
I am about ready to pull the trigger on a AD941.? Then I see that
this Baileigh beast is on sale for less than the quote I got for
the AD941.? This unit does not require a switch over and has a
power drive mech like an AD951.
Thoughts on Baileigh?
Paul
|
Re: Aigner Distometer up alternative?
Oh...not the same title. ?My title was "Aigner Distometer Alternative" and these posts have the title "Aigner Distometer Up Alternative". ?Huh.
|
Re: AD941 vs. Baileigh JP-1898-NC
I would appreciate that.? I have a spare power feeder I was planning on using with the jointer but other projects came along that I haven't pursued this lately. Thanks, Dave
On Tue, Jul 28, 2020 at 3:35 PM Averman, Ed (FAA) via <Ed.Averman= [email protected]> wrote:
Dave ¨C
?
Well, I could, but due to tight quarters where the machine resides, I removed the bracket so I can push the machine back that extra few inches for additional
¡°leg room¡± in my garage. ??
?
If you think it might be useful to you, I can pull the machine out a bit and take a picture of the holes, or maybe with the bracket temporarily/barely installed
to give an idea.?
?
Skip
?
?
?
From: [email protected] <[email protected]>
On Behalf Of David Davies
Sent: Tuesday, July 28, 2020 4:16 PM
To: [email protected]
Subject: Re: [FOG] AD941 vs. Baileigh JP-1898-NC
?
Skip,
? Very interesting.? ?Can you post some pictures?
?
On Tue, Jul 28, 2020 at 3:15 PM Averman, Ed (FAA) via <Ed.Averman=[email protected]> wrote:
My AD 941 came with a PF mounting bracket installed in pre-drilled holes (I ordered it that way).? I think, as David
Best has pointed out, for it to work practically, you need to make a spacer block to get the PF high enough to clear the fence.? I haven¡¯t mounted a PF on mine yet, but what David said is correct.? He made one for his (AD 951 or Dual 51 (not sure which one
he has)), and he has posted pictures, etc.?
?
Skip
?
From:
[email protected] <[email protected]>
On Behalf Of David Davies
Sent: Tuesday, July 28, 2020 4:01 PM
To: [email protected]
Subject: Re: [FOG] AD941 vs. Baileigh JP-1898-NC
?
It will work on the AD951.? But as far as I know not the AD941
?
On Tue, Jul 28, 2020 at 2:56 PM Andy Wojteczko <andy@...> wrote:
Dave you should check with John as to how he knows it will work.
Andy
?
?
Could be, pretty sure Felder told me there was a way to do it because I asked when I bought mine.
?
Mark,
? I'm pretty sure you can't mount it on the AD941.? I have one and there are access panels in that location.
?
I believe i was told that you can mount the same bracket on the ad941, would need to drill the holes. chassis is the same except for the width
?
Another plus with the AD951 is the ability, with the optional mounting bracket to add a Power Feeder.?
-------- Original message --------
Date: 2020-07-28 2:35 p.m. (GMT-05:00)
Subject: Re: [FOG] AD941 vs. Baileigh JP-1898-NC
Sang, I was speaking from experience on AD941 - AD951 about $3500, is true though need to ask to get an accurate quote obviously...
?
Single phase 4hp i think ?(Whatever is the standard.?
The 3piece guard (which I don¡¯t think they say is standard on the web but they include it)
3p 7.5 hp i think (Whatever is the standard)
Variable speed (which is standard)
?
?
On Jul 28, 2020, at 2:27 PM, Sang Luu <sangluu@...> wrote:
?I don't think it's correct to blanket assume you will get 951 standard options that would otherwise be options on the 941.
There are a lot of options on the 951 so I would simply just ask the rep to help guide your decision. They have the pricing structure, which none of us have.?
--
Dave & Marie Davies
318-219-7868
--
Andy Wojteczko
--
Dave & Marie Davies
318-219-7868
--
Dave & Marie Davies
318-219-7868
-- Dave & Marie Davies
318-219-7868
|
Re: Aigner Distometer up alternative?
Oh.... now when on the main page by topics I see that this topic is in 2 parts with the same title. ?
|
Re: Aigner Distometer up alternative?
I wonder if this is a system-forum problem. ?I do not recall seeing this happen before. ?Brian, I also see my original post on this topic when searching by messages, confirming it was not deleted. ? I generally view threads by topic so I can see the original post and follow the replies. ?Strange not seeing my original post when viewing this thread by topic and a number of replies. ?Makes it hard to follow the conversation, and that is especially true for others that may want to offer input as they are missing info. ?
|
Re: AD941 vs. Baileigh JP-1898-NC
Dave ¨C
?
Well, I could, but due to tight quarters where the machine resides, I removed the bracket so I can push the machine back that extra few inches for additional
¡°leg room¡± in my garage. ??
?
If you think it might be useful to you, I can pull the machine out a bit and take a picture of the holes, or maybe with the bracket temporarily/barely installed
to give an idea.?
?
Skip
?
?
?
toggle quoted message
Show quoted text
From: [email protected] <[email protected]>
On Behalf Of David Davies
Sent: Tuesday, July 28, 2020 4:16 PM
To: [email protected]
Subject: Re: [FOG] AD941 vs. Baileigh JP-1898-NC
?
Skip,
? Very interesting.? ?Can you post some pictures?
?
On Tue, Jul 28, 2020 at 3:15 PM Averman, Ed (FAA) via <Ed.Averman=[email protected]> wrote:
My AD 941 came with a PF mounting bracket installed in pre-drilled holes (I ordered it that way).? I think, as David
Best has pointed out, for it to work practically, you need to make a spacer block to get the PF high enough to clear the fence.? I haven¡¯t mounted a PF on mine yet, but what David said is correct.? He made one for his (AD 951 or Dual 51 (not sure which one
he has)), and he has posted pictures, etc.?
?
Skip
?
From:
[email protected] <[email protected]>
On Behalf Of David Davies
Sent: Tuesday, July 28, 2020 4:01 PM
To: [email protected]
Subject: Re: [FOG] AD941 vs. Baileigh JP-1898-NC
?
It will work on the AD951.? But as far as I know not the AD941
?
On Tue, Jul 28, 2020 at 2:56 PM Andy Wojteczko <andy@...> wrote:
Dave you should check with John as to how he knows it will work.
Andy
?
?
Could be, pretty sure Felder told me there was a way to do it because I asked when I bought mine.
?
Mark,
? I'm pretty sure you can't mount it on the AD941.? I have one and there are access panels in that location.
?
I believe i was told that you can mount the same bracket on the ad941, would need to drill the holes. chassis is the same except for the width
?
Another plus with the AD951 is the ability, with the optional mounting bracket to add a Power Feeder.?
-------- Original message --------
Date: 2020-07-28 2:35 p.m. (GMT-05:00)
Subject: Re: [FOG] AD941 vs. Baileigh JP-1898-NC
Sang, I was speaking from experience on AD941 - AD951 about $3500, is true though need to ask to get an accurate quote obviously...
?
Single phase 4hp i think ?(Whatever is the standard.?
The 3piece guard (which I don¡¯t think they say is standard on the web but they include it)
3p 7.5 hp i think (Whatever is the standard)
Variable speed (which is standard)
?
?
On Jul 28, 2020, at 2:27 PM, Sang Luu <sangluu@...> wrote:
?I don't think it's correct to blanket assume you will get 951 standard options that would otherwise be options on the 941.
There are a lot of options on the 951 so I would simply just ask the rep to help guide your decision. They have the pricing structure, which none of us have.?
--
Dave & Marie Davies
318-219-7868
--
Andy Wojteczko
--
Dave & Marie Davies
318-219-7868
--
Dave & Marie Davies
318-219-7868
|
Re: AD941 vs. Baileigh JP-1898-NC
David B and others have had to make the spacer to work in conjunction with using the Smart Stand if memory serves me right. Works fine with the standard PF mounting post. Also might need the longer extension tube.
On Tue, Jul 28, 2020 at 4:15 PM Averman, Ed (FAA) via <Ed.Averman= [email protected]> wrote:
My AD 941 came with a PF mounting bracket installed in pre-drilled holes (I ordered it that way).? I think, as David Best has pointed out, for it to work practically, you need
to make a spacer block to get the PF high enough to clear the fence.? I haven¡¯t mounted a PF on mine yet, but what David said is correct.? He made one for his (AD 951 or Dual 51 (not sure which one he has)), and he has posted pictures, etc.?
?
Skip
?
From: [email protected] <[email protected]>
On Behalf Of David Davies
Sent: Tuesday, July 28, 2020 4:01 PM
To: [email protected]
Subject: Re: [FOG] AD941 vs. Baileigh JP-1898-NC
?
It will work on the AD951.? But as far as I know not the AD941
?
On Tue, Jul 28, 2020 at 2:56 PM Andy Wojteczko <andy@...> wrote:
Dave you should check with John as to how he knows it will work.
Andy
?
?
Could be, pretty sure Felder told me there was a way to do it because I asked when I bought mine.
?
Mark,
? I'm pretty sure you can't mount it on the AD941.? I have one and there are access panels in that location.
?
I believe i was told that you can mount the same bracket on the ad941, would need to drill the holes. chassis is the same except for the width
?
Another plus with the AD951 is the ability, with the optional mounting bracket to add a Power Feeder.?
-------- Original message --------
Date: 2020-07-28 2:35 p.m. (GMT-05:00)
Subject: Re: [FOG] AD941 vs. Baileigh JP-1898-NC
Sang, I was speaking from experience on AD941 - AD951 about $3500, is true though need to ask to get an accurate quote obviously...
?
Single phase 4hp i think ?(Whatever is the standard.?
The 3piece guard (which I don¡¯t think they say is standard on the web but they include it)
3p 7.5 hp i think (Whatever is the standard)
Variable speed (which is standard)
?
?
On Jul 28, 2020, at 2:27 PM, Sang Luu <sangluu@...> wrote:
?I don't think it's correct to blanket assume you will get 951 standard options that would otherwise be options on the 941.
There are a lot of options on the 951 so I would simply just ask the rep to help guide your decision. They have the pricing structure, which none of us have.?
--
Dave & Marie Davies
318-219-7868
--
Andy Wojteczko
--
Dave & Marie Davies
318-219-7868
|
Re: AD941 vs. Baileigh JP-1898-NC
Skip, ? Very interesting.? ?Can you post some pictures? Thanks Dave
On Tue, Jul 28, 2020 at 3:15 PM Averman, Ed (FAA) via <Ed.Averman= [email protected]> wrote:
My AD 941 came with a PF mounting bracket installed in pre-drilled holes (I ordered it that way).? I think, as David Best has pointed out, for it to work practically, you need
to make a spacer block to get the PF high enough to clear the fence.? I haven¡¯t mounted a PF on mine yet, but what David said is correct.? He made one for his (AD 951 or Dual 51 (not sure which one he has)), and he has posted pictures, etc.?
?
Skip
?
From: [email protected] <[email protected]>
On Behalf Of David Davies
Sent: Tuesday, July 28, 2020 4:01 PM
To: [email protected]
Subject: Re: [FOG] AD941 vs. Baileigh JP-1898-NC
?
It will work on the AD951.? But as far as I know not the AD941
?
On Tue, Jul 28, 2020 at 2:56 PM Andy Wojteczko <andy@...> wrote:
Dave you should check with John as to how he knows it will work.
Andy
?
?
Could be, pretty sure Felder told me there was a way to do it because I asked when I bought mine.
?
Mark,
? I'm pretty sure you can't mount it on the AD941.? I have one and there are access panels in that location.
?
I believe i was told that you can mount the same bracket on the ad941, would need to drill the holes. chassis is the same except for the width
?
Another plus with the AD951 is the ability, with the optional mounting bracket to add a Power Feeder.?
-------- Original message --------
Date: 2020-07-28 2:35 p.m. (GMT-05:00)
Subject: Re: [FOG] AD941 vs. Baileigh JP-1898-NC
Sang, I was speaking from experience on AD941 - AD951 about $3500, is true though need to ask to get an accurate quote obviously...
?
Single phase 4hp i think ?(Whatever is the standard.?
The 3piece guard (which I don¡¯t think they say is standard on the web but they include it)
3p 7.5 hp i think (Whatever is the standard)
Variable speed (which is standard)
?
?
On Jul 28, 2020, at 2:27 PM, Sang Luu <sangluu@...> wrote:
?I don't think it's correct to blanket assume you will get 951 standard options that would otherwise be options on the 941.
There are a lot of options on the 951 so I would simply just ask the rep to help guide your decision. They have the pricing structure, which none of us have.?
--
Dave & Marie Davies
318-219-7868
--
Andy Wojteczko
--
Dave & Marie Davies
318-219-7868
-- Dave & Marie Davies
318-219-7868
|
Re: AD941 vs. Baileigh JP-1898-NC
My AD 941 came with a PF mounting bracket installed in pre-drilled holes (I ordered it that way).? I think, as David Best has pointed out, for it to work practically, you need
to make a spacer block to get the PF high enough to clear the fence.? I haven¡¯t mounted a PF on mine yet, but what David said is correct.? He made one for his (AD 951 or Dual 51 (not sure which one he has)), and he has posted pictures, etc.?
?
Skip
?
toggle quoted message
Show quoted text
From: [email protected] <[email protected]>
On Behalf Of David Davies
Sent: Tuesday, July 28, 2020 4:01 PM
To: [email protected]
Subject: Re: [FOG] AD941 vs. Baileigh JP-1898-NC
?
It will work on the AD951.? But as far as I know not the AD941
?
On Tue, Jul 28, 2020 at 2:56 PM Andy Wojteczko <andy@...> wrote:
Dave you should check with John as to how he knows it will work.
Andy
?
?
Could be, pretty sure Felder told me there was a way to do it because I asked when I bought mine.
?
Mark,
? I'm pretty sure you can't mount it on the AD941.? I have one and there are access panels in that location.
?
I believe i was told that you can mount the same bracket on the ad941, would need to drill the holes. chassis is the same except for the width
?
Another plus with the AD951 is the ability, with the optional mounting bracket to add a Power Feeder.?
-------- Original message --------
Date: 2020-07-28 2:35 p.m. (GMT-05:00)
Subject: Re: [FOG] AD941 vs. Baileigh JP-1898-NC
Sang, I was speaking from experience on AD941 - AD951 about $3500, is true though need to ask to get an accurate quote obviously...
?
Single phase 4hp i think ?(Whatever is the standard.?
The 3piece guard (which I don¡¯t think they say is standard on the web but they include it)
3p 7.5 hp i think (Whatever is the standard)
Variable speed (which is standard)
?
?
On Jul 28, 2020, at 2:27 PM, Sang Luu <sangluu@...> wrote:
?I don't think it's correct to blanket assume you will get 951 standard options that would otherwise be options on the 941.
There are a lot of options on the 951 so I would simply just ask the rep to help guide your decision. They have the pricing structure, which none of us have.?
--
Dave & Marie Davies
318-219-7868
--
Andy Wojteczko
--
Dave & Marie Davies
318-219-7868
|
Re: AD941 vs. Baileigh JP-1898-NC
You should check with Felder, they will surely know more than us...
toggle quoted message
Show quoted text
On Jul 28, 2020, at 3:56 PM, Andy Wojteczko <andy@...> wrote:
? Dave you should check with John as to how he knows it will work. Andy ? ? Could be, pretty sure Felder told me there was a way to do it because I asked when I bought mine.
On Jul 28, 2020, at 3:06 PM, David Davies <myfinishingtouch@...> wrote: ? Mark, ? I'm pretty sure you can't mount it on the AD941.? I have one and there are access panels in that location. ? I believe i was told that you can mount the same bracket on the ad941, would need to drill the holes. chassis is the same except for the width ? Another plus with the AD951 is the ability, with the optional mounting bracket to add a Power Feeder.? -------- Original message -------- Date: 2020-07-28 2:35 p.m. (GMT-05:00) Subject: Re: [FOG] AD941 vs. Baileigh JP-1898-NC Sang, I was speaking from experience on AD941 - AD951 about $3500, is true though need to ask to get an accurate quote obviously... ? Single phase 4hp i think ?(Whatever is the standard.? The 3piece guard (which I don¡¯t think they say is standard on the web but they include it) 3p 7.5 hp i think (Whatever is the standard) Variable speed (which is standard) ?
On Jul 28, 2020, at 2:27 PM, Sang Luu <sangluu@...> wrote: ?I don't think it's correct to blanket assume you will get 951 standard options that would otherwise be options on the 941. There are a lot of options on the 951 so I would simply just ask the rep to help guide your decision. They have the pricing structure, which none of us have.?
-- Dave & Marie Davies
318-219-7868
-- Andy Wojteczko
|
Re: AD941 vs. Baileigh JP-1898-NC
It will work on the AD951.? But as far as I know not the AD941 Dave
On Tue, Jul 28, 2020 at 2:56 PM Andy Wojteczko < andy@...> wrote: Dave you should check with John as to how he knows it will work. Andy ? ? Could be, pretty sure Felder told me there was a way to do it because I asked when I bought mine. ? Mark, ? I'm pretty sure you can't mount it on the AD941.? I have one and there are access panels in that location. ? I believe i was told that you can mount the same bracket on the ad941, would need to drill the holes. chassis is the same except for the width ? Another plus with the AD951 is the ability, with the optional mounting bracket to add a Power Feeder.? -------- Original message -------- Date: 2020-07-28 2:35 p.m. (GMT-05:00) Subject: Re: [FOG] AD941 vs. Baileigh JP-1898-NC Sang, I was speaking from experience on AD941 - AD951 about $3500, is true though need to ask to get an accurate quote obviously... ? Single phase 4hp i think ?(Whatever is the standard.? The 3piece guard (which I don¡¯t think they say is standard on the web but they include it) 3p 7.5 hp i think (Whatever is the standard) Variable speed (which is standard) ?
On Jul 28, 2020, at 2:27 PM, Sang Luu <sangluu@...> wrote: ?I don't think it's correct to blanket assume you will get 951 standard options that would otherwise be options on the 941. There are a lot of options on the 951 so I would simply just ask the rep to help guide your decision. They have the pricing structure, which none of us have.?
-- Dave & Marie Davies
318-219-7868
--
Andy Wojteczko
-- Dave & Marie Davies
318-219-7868
|
Re: AD941 vs. Baileigh JP-1898-NC
Dave you should check with John as to how he knows it will work. Andy ?
toggle quoted message
Show quoted text
From: [email protected] [mailto:[email protected]] On Behalf Of Mark Kessler
Sent: Tuesday, July 28, 2020 3:12 PM
To: [email protected]
Subject: Re: [FOG] AD941 vs. Baileigh JP-1898-NC? Could be, pretty sure Felder told me there was a way to do it because I asked when I bought mine.
On Jul 28, 2020, at 3:06 PM, David Davies <myfinishingtouch@...> wrote: ? Mark, ? I'm pretty sure you can't mount it on the AD941.? I have one and there are access panels in that location. ? I believe i was told that you can mount the same bracket on the ad941, would need to drill the holes. chassis is the same except for the width ? Another plus with the AD951 is the ability, with the optional mounting bracket to add a Power Feeder.? -------- Original message -------- Date: 2020-07-28 2:35 p.m. (GMT-05:00) Subject: Re: [FOG] AD941 vs. Baileigh JP-1898-NC Sang, I was speaking from experience on AD941 - AD951 about $3500, is true though need to ask to get an accurate quote obviously... ? Single phase 4hp i think ?(Whatever is the standard.? The 3piece guard (which I don¡¯t think they say is standard on the web but they include it) 3p 7.5 hp i think (Whatever is the standard) Variable speed (which is standard) ?
On Jul 28, 2020, at 2:27 PM, Sang Luu <sangluu@...> wrote: ?I don't think it's correct to blanket assume you will get 951 standard options that would otherwise be options on the 941. There are a lot of options on the 951 so I would simply just ask the rep to help guide your decision. They have the pricing structure, which none of us have.?
-- Dave & Marie Davies
318-219-7868
-- Andy Wojteczko
|
Re: Aigner Distometer up alternative?
If you look at the topic, a lot of messages are not there, if you look at messages, they are all there. Not sure why, but no messages have been removed.
toggle quoted message
Show quoted text
Seems like my original post was removed along with the one to follow by Dave Davies and perhaps others. ?Strange. ?
|
Bill Belanger
David P. Best
imran