|
Re: Start Capacitor Value
开云体育JM, Thanks for the feedback. I suspect the same, i.e., label has the start cap value. Not sure why the field name “cond” - likely stands for conditioning. Not sure know what else could it be. Anyhow, I thought the person at laguna would be able to confirm on phone but no such luck, need to wait for the tech dept to respond. Mine is a two wire leaded, without terminals. I have found similar sized ones on the sites i have ordered from before however the dia is 45mm vs 50mm. So still looking. I had checked newark but not the other site you sent so will check them out. BTW, polypropylene caps are more robust (usually specified for run caps) but I try to use them for start cap as well. I was hoping to get a confirmation by end of day yesterday. I think it is low risk to order it based upon label value but I may wait till monday. Imran? On Jan 16, 2021, at 8:04 PM, jjmotzi <john.motzi@...> wrote:
?The label says 50?F (microFarads) 450V.? I needed to replace the start capacitor on my 20 year old Inca table saw earlier this year.? Slightly larger motor (2.2 kW) than what you have here, but similar.? Typically you can find replacements at Newark electronics Newark.com, or ? Mine was a 4-wire lead so I replaced with the same.? Easier to find are the 2-wire models.? Mine was a 40?F but I'll give you the links anyway to get you in the right sections of the webstores: 4-Wire Leads: 2-Wire Leads:?? I chose the model based on the correct specs but also the physical dimensions so it would mount the same way on my motor. Hope this helps JM |
|
Re: Spindle Sander
开云体育Dmitry, I was warned to stay away from the sanding drum kit on shaper due to RPM being too high. Do you have variable speed on shaper? Imran On Jan 16, 2021, at 8:45 PM, Dmitry Ivanovs via groups.io <divanov2@...> wrote:
?Overkill !! Why not just buy head for shaper from felder different diameters. That’s what I’m using if need it? Elegance Custom Cabinetry? Minneapolis, Minnesota? Dmitry Ivanovs . On Jan 16, 2021, at 16:08, PK <paul.kellymjc@...> wrote:
|
|
Re: Spindle Sander
开云体育Overkill !! Why not just buy head for shaper from felder different diameters. That’s what I’m using if need it?Elegance Custom Cabinetry? Minneapolis, Minnesota? Dmitry Ivanovs . On Jan 16, 2021, at 16:08, PK <paul.kellymjc@...> wrote:
|
|
Re: Hammer C-31 Planer Issue - Motor Triping
开云体育Too bad. The bracket looks like AL, if that was the only item, I probably try to straighten it but key being welded is a non starter. I have not worked with a lot of motors but I have seen the ramp on the end of key trench (perhaps due to milling) but the key sat flat and the groove on the pulley is flat. If i understand you correctly the key projection from shaft is ramped. I am curious if that is intended or an error. Imran On Jan 16, 2021, at 6:51 PM, annu.marwaha@... wrote:
?Hey Imran, the key is welded to the shaft. ?I can see the small filet weld towards the motor housing. ?The brackets are also part of the motor housing. ?I’ll have to get Felder to address it. -Annu |
|
Re: Hammer C-31 Planer Issue - Motor Triping
开云体育Hi Annu, I feel your frustration. I am sure this is already considered but can the brackets be transferred from old to new motor? I am not sure how the pulley is retained on the shaft but could the key be cut to the length that matches the flat portion of the slot or a new shorter key purchased. Key material is fairly common. I am assuming the new motor is designed to work with shorter key. Imran On Jan 16, 2021, at 6:25 PM, annu.marwaha@... wrote:
?Well...i'm seriously frustrated now....the new motor that was sent has a different motor shaft key than the original motor.? The new motor's key is like a ramp and the old motor's key is flat.? So now i can't fit the belt pully onto the new motor.? Additionaly, when i got the new motor off the foam padding it was sitting on in the shipping box, i realized that mounting bracklets are both bent.? so even if I could have put the pully on the motor, there was no way that I would have been able to install and allign it.? Now i will have to rerent the pallet jack and trailer to bring it home whenever Felder addresses this.? I've attached some pictures below.? In the picture of the new motor, the old motor is on the top and the new motor is on the bottom.? You can clearly see that the old motor's brackets are nice and flat and the new motor's brackets are not.? I'm assuming that they are not supposed to be like that and bent into shape during bolting.? All i want to do is relax in my workshop and make some damn furniture..... Annu PS...i did confirm the ground short on the original motor after I removed the wiring harness. <old motor key.jpg> <new motor key.jpg> <motor comparison.jpg> |
|
Re: Hammer C-31 Planer Issue - Motor Triping
Well...i'm seriously frustrated now....the new motor that was sent has a different motor shaft key than the original motor.? The new motor's key is like a ramp and the old motor's key is flat.? So now i can't fit the belt pully onto the new motor.? Additionaly, when i got the new motor off the foam padding it was sitting on in the shipping box, i realized that mounting bracklets are both bent.? so even if I could have put the pully on the motor, there was no way that I would have been able to install and allign it.? Now i will have to rerent the pallet jack and trailer to bring it home whenever Felder addresses this.? I've attached some pictures below.? In the picture of the new motor, the old motor is on the top and the new motor is on the bottom.? You can clearly see that the old motor's brackets are nice and flat and the new motor's brackets are not.? I'm assuming that they are not supposed to be like that and bent into shape during bolting.? All i want to do is relax in my workshop and make some damn furniture.....
Annu PS...i did confirm the ground short on the original motor after I removed the wiring harness. |
|
Re: Hammer C-31 Planer Issue - Motor Triping
Roger S
开云体育This is for a three-phase but looks as if it fits what you’ve got. ?I think you can ignore it since the C3-31 has it built-in already.
|
PK
imran
