sure does look the same. good that it works for you. mine is fixed now. plan to replace kip levers with cam levers that Brian suggested. that should make it easy to reinstall to the floater nut that i intend to leave in front of short xcut fence nut.
imran?
toggle quoted message
Show quoted text
On Nov 30, 2020, at 7:38 PM, Mark Kessler <mkessler10@...> wrote: ? Imran, looks like the same handle, here are some pics. Might be due to the round over I have in any case no issues taking on/off. <image0.jpeg> <image1.jpeg> On Nov 28, 2020, at 8:25 PM, imranindiana via groups.io <imranindiana@...> wrote:
? Mark,
interesting that your come off as it is essentially same size as mine. seems like, you may have seen the pic i sent you where i showed the slight slot i made in the slider handle. the nut you show has a generous round over, perhaps that helped. i also wonder if the handle is slightly diff. does your look like this:
i know couple of other folks may have this issue. if you do not want to shorten the nut this is an option.
imran
On Nov 28, 2020, at 8:14 PM, Mark Kessler <mkessler10@...> wrote:
? Imran,? duno, I have flat steel bar for my clamps and have no issues they are99mm x 31.76 x 12.5 (btw, they can come off the xroll with clamp attached with no modification the the handle on the xroll) <image0.jpeg> <image1.jpeg> On Nov 28, 2020, at 8:06 PM, imranindiana via groups.io <imranindiana@...> wrote:
? Mark,
i guess i can see benefit in softer material however, that is due to material not due to application. Felder provides T-Nuts for the secured nut for the short xcut fence. these are secured by cap screws so i take it they went with the t nut for space required to recess them. as for guidance, i have zero issues with sliding big squeeze clamps in the slot.
i wondered if they are meant to limit pinch force but i do not think they are made to a tolerance to work as such. not sure if it is even possible because of variation i have seen in slider slot lip thickness.
imran?
On Nov 28, 2020, at 7:55 PM, Mark Kessler <mkessler10@...> wrote:
? Imran, I can think of a few benefits of a t-nut over non T, one would be additional pull out strength due more threads in a softer material like an aluminum or even steel if the application calls for it the other would be if you require guidance I suppose? On Nov 28, 2020, at 7:50 PM, Mark Kessler <mkessler10@...> wrote:
? Nice nuts - Mac... On Nov 28, 2020, at 7:35 PM, imranindiana via groups.io <imranindiana@...> wrote:
? Mac,
one i have from felder for KF700 xcut fence (one that floats in slot, not the fixed one) is flat and not t-nut.? it measured 30x10mm i did not measure the length. no chamfers. BTW, what is the benefit of a T-Nut?
i have only shipped ~150 in 1.25¡±x0.5¡± with no complaints. i just carried fwd the stock established by the original big squeeze. many ways to skin a cat ?
Imran On Nov 28, 2020, at 7:23 PM, Airtight: Clamps by Air Compression <airtightclamps@...> wrote: ? Martin on right Felder on left
Designing and building for 50 years On Nov 28, 2020, at 6:10 PM, Airtight: Clamps by Air Compression via groups.io <airtightclamps@...> wrote:
? I have made over1000 nuts but never made one 1.25 in width all Felder are 30 mm shouldered at around 20 mm for t slot table width. 303 stainless steel? 10 mm x 1.5 thread ,, beveled on 22 edges than cleaned and polished 100 mm in length usually . Mac,, Designing and building for 50 years On Nov 28, 2020, at 5:07 PM, imranindiana via groups.io <imranindiana@...> wrote:
? i got a question on tolerance for the nut. i had not looked this up before but i found general info for CR1018 in the size i plan to use and tolerance is +0/-0.004. i will verify with supplier on monday and share if it is different.
i also measured the one nut that i built earlier this yr. it meets the tolerance given above. this is a ~4¡± long nut.
above is xroll. the bottom edges will be chamfered for pre-xroll.
imran?
On Nov 26, 2020, at 9:29 PM, imranindiana via groups.io <imranindiana@...> wrote:
? Cliff,after posting i realized that i should have added some details. figured, i will wait to see if there is any interest to start with. but since you brought it up, here it goes:made out of CR1018 0.5¡± x 1.25¡± flat bar stock. you need to let me know if your machine is xroll or pre-xroll. i cannot guarantee compatibility with non-felder machines.nut length is 2¡± but you can specify any length at $1/in for nuts over 2¡± in length. if shipping is affected i will let you know.one tapped hole of your choice in the middle of the nut from std offerings up to M8 or 5/16¡± and associated coarse thread.i will entertain your need outside what i have listed above as long as i have the tap, just let me know what you need.imranOn Nov 26, 2020, at 7:50 PM, Cliff Rohrabacher, Esq. <rohrabacher@...> wrote:?tell whether they can select their preference for the thread in thetapped hole. ?mm ?imperial, ?& what size, that sort of thingOn 11/26/20 12:17 PM, imranindiana via groups.io wrote:well i need to make a few for myself and thought i check if anyone is interested. this is basic cold rolled steel 1018. pre xroll slider need two edges chamfered. i am thinking 1 for $25, 2 for $40 and 3 for $50 shipped to lower 48.
please select reply to sender below if you are interested.
imran
|
imran