Re: Android APP ETA
2024/2025 or ....?
By
p_dmitrii
·
#252168
·
|
Re: Question about Crestron Mobile panels....
I recommend you use Simpl Debugger to see what is happening when you press the buttons in the iPads that are not working as you are expecting. My guess is that there are some issues with the code. If
By
Matt Jones
·
#252167
·
|
Re: Question about Crestron Mobile panels....
Thanks but the ipads are receiving the new updated graphics programs. And yes I have to load each one directly but thats ok. The problem is that the two in question are not recognizing the updated
By
Nightcountry
·
#252166
·
|
Re: Question about Crestron Mobile panels....
FTR, Use Local file=ON means that you have to load the graphics file directly to each iPad. if one/more still have the old project (i.e. not the new project) you'll see what you're experiencing. If
By
ckangis
·
#252165
·
|
Re: Converting PAC2 to dumb Cresnet "landing point"
I actually recently did this... In short, the CresNet buss isn't shared all the way through,? so I used the existing 300wPs, for a connection to one port on each row. Below are my notes from the work
By
CO Cowboy
·
#252164
·
|
Re: Question about Crestron Mobile panels....
The Use Local File is set to on in all four panels. By changing any of them to off, the program will not run. So must be something else. Thanks for the suggestion though.
By
Nightcountry
·
#252163
·
|
Re: Question about Crestron Mobile panels....
Make sure the Use Local File is set to off , in the crestron mobile app of those two ipads
By
Deuterios
·
#252162
·
|
Re: rtpMIDI
Dustin, This looks incredibly promising, thank you for sharing! I have also initiated a feature request with Renewed Vision for the ability to send arbitrary strings to a TCP/IP device which was not
By
Phil Moore
·
#252161
·
|
Question about Crestron Mobile panels....
Have a? 2 series processor (MP2E) and multiple Ipads. The ipads all have the same VT program in them but when I added in a projector (IR Commands) to simpl, the two ipad mini panels do not "see" the
By
Nightcountry
·
#252160
·
|
Re: Converting PAC2 to dumb Cresnet "landing point"
I second replacing it with a couple of DIN-HUBs and DIN-PWS-60's. This is where I find the restrictions on the DIN-CEN-CN's terribly unfortunate.? It makes them almost completely useless for a
By
Robert Ray
·
#252159
·
|
Re: Converting PAC2 to dumb Cresnet "landing point"
The PAC2 had a built in Cresnet Hub (CNX-HUB equivalent) ¨C I would probably recommend getting the PAC2 out of the equation as a point of failure and replacing it with a DIN-HUB or CNX-HUB) but if
By
Lincoln King-Cliby
·
#252158
·
|
Re: Converting PAC2 to dumb Cresnet "landing point"
Hi Bruce, I have a couple of PAC2's I'm considering the best path on as well -- I am convinced that those 8 Cresnet busses (A thru H) are electrically isolated from one another, and the processor
By
Michael Caldwell-Waller
·
#252157
·
|
Re: Converting PAC2 to dumb Cresnet "landing point"
If I'm understanding what you are asking, you could just use a CNTBLOCK with the internal power jumper cut. That would isolate power between the two sides but still let cresnet data pass between the
By
BruteForceIsUnderRated
·
#252156
·
|
Converting PAC2 to dumb Cresnet "landing point"
I will be updating an ancient system with a PAC2 and CLX dimmers and CNX-BXX keypads to Crestron Home in a few weeks. There's a load of the field Cresnet wires landed right on the PAC2 on its many
By
spannertech@...
·
#252155
·
|
Re: NAX - Receiving AES67 from Dante Devices
#crestronhome
#nax
Im able to do this manually. I was wondering if anybody had a way to accomplish this in Crestron Home. Thanks
By
Yitzy Novak
·
#252154
·
|
Re: NAX - Receiving AES67 from Dante Devices
#crestronhome
#nax
Don't know about CHome, but to do it manually: Enable AES67 on the Dante device in Dante Controller Create AES67 mcast transmiter (must be 2 channels) thru DC and take note of the mcast IP Enter the
By
ZS
·
#252153
·
|
NAX - Receiving AES67 from Dante Devices
#crestronhome
#nax
Is there any solutions to be able to start a AES67 stream from Crestron Home. I have a secondary processor running SIMPL so I can trigger what's necessary to start the stream. The issue I'm running
By
Yitzy Novak
·
#252152
·
|
Re: D3Pro: Program Generated Incomplete
Hi All Happy New Year was this ever resolved? or do we still need to stay on old Data base? Thanks
By
@Stujrob
·
#252151
·
|
Re: rtpMIDI
I put together a very quick demo of receiving note on/off RTP-MIDI messages directly in Simpl from ProPresenter on a PC. Since you're on Windows, I assume you're using the rtpMIDI app from Tobias
By
Dustin Hurlock
·
#252150
·
|
Re: rtpMIDI
I get that. They were overly PC as well, and I begrudgingly accepted that we were moving to Mac in that venue. I suggest looking at https://benjamin.kuperberg.fr/chataigne/en as an intermediary with
By
Caleb Radecky
·
#252149
·
|