开云体育

Exactly Lincoln – thanks for clarifying. Cheers, Thorsten Von: [email protected] <[email protected]> Im Auftrag von Lincoln King-Cliby via groups.io Gesendet: Montag, 21. Juni 2021 15:53 An:

I just tried Wyatt's fix but it did not work for me.? When I went to change the setting, it was already checked.? So I unchecked it, tried it, didn't work.? Then went back and re-checked the box,

I believe what Thorsten is saying is that in the existing program they’re currently being used as Ethernet IO devices (along the lines of a QM-RMC in ESlave mode without the processing power) – I

If you aren't even using the HDMI, just leave the DM port disconnected and connect them to the LAN via the LAN port instead.? No need to EISCs to them.? They will just be another Ethernet device

So since updating to the 1.8 FW I'm now getting these errors & restarts once a day as opposed to once every four days before. I'm going to roll back to a much earlier FW when I get home at the end of

I hit the green play triangle, "Run Project As" at the top all the time with mobile projects and it works fine.? If you get a simulator that is blank you have to change the Advanced Attributes in

Hi, thanks for the suggestion, but that would be bit over the top. There are a couple of RMC-100 and they are not even used for HDMI, but only for IR/RS232. So I think i?ll go with EISCs. Cheers,

Thanks. I thought as much. It’s good to get the confirmation though. It’s easy enough to upload it so the processor as well and just use the app on the phone to test as well. I will give the save

I had a pretty lengthy conversation with Crestron TB a few months back about this, and they confirmed it doesn't work.? Their solution was to do a "save as" and select xpanel. I know this isn't

This is probably? a simple question. I have a few remotes that are working well ( tsr 302 , tsr 310) as well as crestron touch screens.? My GUI in all of those is established and setup. I have

I misspoke.? I meant to say "Cresnet Slave"

I have an existing Crestron CP3 based system with Lutron Caseta as the lighting. It works well and does what I need. Looking at the Crestron Home system but it does not support the Caseta lighting (it

Not possible to make the CP2 an ESlave because the CP2 doesn’t have Ethernet ? You needed the CP2E for that -- Lincoln King-Cliby, CTS, DMC-E-4K/T/D Commercial Market Director Sr. Systems

It would be possible to move a DM-RMC-100C to the new system while keeping all the old DM-RMC-100 on the old system.? However it will not be cheap.? What you can do is buy a DM-TX-4KZ-100-C-1G for

Hi Lincoln, sorry for being unprecise on the part number – it?s indeed about a DM-RMC-100. So I guess the only route to run the new system in parallel to the old system is to use EISC. However, I

RMC100 isn't a complete/valid part number... Do you mean a QM-RMC, a DM-RMC-100, a DM-RMC-100-C, RMC3, RMC4, or something else? If it is a QM-RMC or RMC3 you can only have one master if it is in

Hi, i?m currently doing a rebuild of an existing system to a new one. The system uses a couple of old RMC100 to remote control devices via IR. These are included in the existing program as separate

Did he sign up to be a beta tester when he downloaded the app?? It will say "Crestron Home (Beta)" at the top on the Play Store app page.? I am curious.I am, I feel your pain, and the last app

Thanks Troy wrote:

Yes, yes, very true!