开云体育

I think I have discovered an issue with the MVMAX. It seems to change on it's own, based on signal source type. Notice below Putty exchange: MV? //volume poll after power on MV48 MVMAX 80 //as

You can use the console symbol along with the command fput. This is the command format: FPUTfile [url] [local_path] {username:password} {proxy} url - fully qualified URL to the file being uploaded to

Hi Does anyone know how to write a file to an FTP server from the program like writing to \\NVRAM ?

It would *appear* that this unit is an electronic transformer. have you tried hard-setting the 2DIMU8 to ELV for that load instead of using the adaptive mode?

So, I have a lighting system with these drivers and they dim like crap.? 2DIMU8 as well as a DELVEX.? This unit is 24VAC output.? Does anyone know of a replacement with 0-10V control?

no I have not but we sent some back to crestron and they said needed to replace screen these Tsw's were in questionable locations(almost outdoors) near the Ocean, But now seeing it in environmentaly

I notice in the control protocol there are 3-4 different channel level commands. Some of them make sense, for example LFE level only, could mean adjusting the source LFE level without touching the

Have you tried re-flashing the FW? just something to try... If you're not updating, just reloading the same version, make sure to add the 'All' suffix... EX: puf?tsx_1.501.0013.004.puf all Worth a

So encountering more and more tsw750 that are loosing top and bottom 3/4 inches touch sensitivity--so even in diagnostic page the Calibrate button can't be pushed--in info page tools "setup" ther is a

Thanks you Chris, that looks perfect. I appreciate the help! -andy

?If you don’t care about Envy_AR_300 (all x’s on input row) why have it in the truth table?“ Mh, might be a leftover from permanent changes on the code. There should actually be an “H” in

The following files and folders have been uploaded to the Files area of the [email protected] group. * /Sony STR-ZAxx v1.1_archive.zip (

I just added the ZA Module to the files section that I've used since Jan. 2017 - *Sony STR-ZAxx v1.1_archive.zip* I has Direct volume control and fixes a Comms issue that I found as well as the

If you don’t care about Envy_AR_300 ?(all x’s on input row) why have it in the truth table? From: <[email protected]> on behalf of Thorsten K?hler <thorsten.koehler@...> Reply-To:

There is a Sony STR-ZAxx module that is from old database and has the newtonsoft dependency.? It uses 0 – 100% analog input for volume.? You can also use a Crestron connected approach, also uses 0

Its been awhile since I did resi work and had to control an AV receiver. I am helping a friend out with a sony STR-ZA1100ES and I need to be able to set discrete volume levels on the main zone of the

Are the output signals being jammed elsewhere? e.g. within a module wrote:

What is it with integrators doing generic HDbT TX/RX units on DM switches instead of DM-TX or DM-RMCs? ?Just had 2 takeover jobs with that same silliness. ?Heck one of them even used Crestron HDbT

Try that share: <https://koehlermedientechnik-my.sharepoint.com/:f:/g/personal/thorsten_koeh ler_koehler-medientechnik_de/Ep8Ls0vgrc1Iplnje1Pp_r8B0V92o83gLUj-Lcs5lbwdqA? e=hO8Kmu>

If you were able to post a link to a screen shot of the TT and Debuger with states of the inputs/outputs to the TT we could probably figure out what is causing the pulsed behavior. I use TTs pretty