开云体育

Hey Don, I'm afraid I cannot be of any help on this one since I also lack experience with Home. However, it is great to hear you are still out there delving in. Best of luck!! Dennis Sweet

Hi there’s no way to do it natively. but you could try to convert the CP3-R into a CP3 for Simp Windows and use de Pyng Modules that way you can send and get signals from Pyng / Crestron Home to

Disregard. Been awhile since using AVF. I needed to go to Manage Devices and actually add the driver for the projector. After that I was able to assign the HD-CTL-101 COM to it.

Hi all, Is can control crestron NVX system with kramer control system. Sent from Outlook for Android<https://aka.ms/AAb9ysg> ________________________________ Sent: Friday, June 7, 2024 2:15:45 AM To:

The Global Cache GC-IRE might work, connected to the NVX decoder's RS-232 port. I'm not sure if its serial output could then be routed directly to a Global Cache transmitter in the program, or if

All, I cannot get CEC to work with any of the samsung displays here on site. They are mix of Signage and OFE consumer units. None of them work, always get '@E' as reply no matter what I send or what

Yes, there is IR ports on the DM-NVX transmitter, but my problem is to grab the IR signals from the cable box remote at the NVX receiver and send them in real time to the NVX transmitter.

Can anyone tell me how (or even if) the power commands are managed to a display, when a HD-CTL-101 is added to the IP Table of a MPC3-102 in AVF? I have all the gear on my test bench except for the

Do you not have a processor or NVX transmitter at the remote end? You should have IR ports there.

Hi, Could you share the Reavon X100 driver also with me? Thanks in advance, Eduards

Hi, The analog outputs 1-2-3-4 will always correspond to zones 1-2-3-4 in any situation. There is no special programming needed. Though, if you want it to be a pure line-level output instead of

Hello all, Does anyone have use the 1-2 3-4 analog outputs on this amplifier? Is it works like the unbalanced output of the C2N-AMP 6x100? I don't see any instructions to activate them. Thanks. Angel

You totally could do it exactly as you propose for debug purposes, especially if it's just for inspecting variables in real time and you don't care about packet loss. For me, I'm actually driving

Hello. Is there an easy way to have an IR receiver on the display side and an IR transmitter on the source side? Example, a customer wants to control a remote cable box from the display side. I was

It was on a system tested March of last year, the zone status was working. The driver at the time was HS2064_3.0000.0005IP from what I see in the program we tested. I have a co-worker who rolled out a

Fair point, MQTT is fairly complex and it would be hard to write by hand without a library. The more I think about operationalizing this at scale, I'm not sure if MQTT is a good fit for my situation.

I think you’re looking for analog logic symbol called “log with limits”. I haven’t poked at the maths for it, but frequencies are a logarithmic scale. You may have to poke at the numbers a bit

Hi All, I'm seeking a way to control a filter's frequency in a parametric EQ block in Biamp. I have successfully achieved control of it in a linear sense, but the problem is that the frequency range

Hello, all.? I'm a first-time poster here, but a long-time SIMPL programmer and a relatively inexperienced Crestron Homer. Is there a way to pair CP3-R relays and/or I-O ports in an OS2 Pyng program,

Has anyone found a good driver that provides full control of the roku on crestron home? Calling up directly to the apps and sending the remote's preset 1 and 2.